scholarly journals Study on the Corrosion Resistance of 39SiCrVTiA High strength and high toughness spring steel

2021 ◽  
Vol 353 ◽  
pp. 01010
Author(s):  
Lun Nie ◽  
Min Zhu ◽  
Shirun Tu ◽  
Kefeng Yuan ◽  
Kexin Lu
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Polarization Curve ◽  
Electrochemical Impedance ◽  
High Strength ◽  
Spring Steel ◽  
Test Results ◽  
Heat Treated ◽  
Spring Steels

39SiCrVTiA spring steel is heat-treated and compared with the existing high-strength spring steels 60Si2CrVA and SAE9254 for electrochemical impedance spectroscopy (EIS), polarization curve and slow strain rate testing (SSRT). The test results of electrochemical impedance spectroscopy (EIS), polarization curve show that the corrosion resistance of 60Si2CrVA was the best, followed by that of SAE9254 and 39SiCrVTIA.However, the test results of the SSRT test show that the three spring steels in 5% NaCl solution possess high SCC susceptibility. The SCC susceptibility of 39SiCrVTiA steel is slightly lower and the stress corrosion ability is better than the other two steels which may be related to its containing Ti, V elements and lower carbon content.

Electrochemical Behavior of Mg in H3PO4 and Phosphating Solution

2014 ◽  
Vol 1081 ◽  
pp. 318-321 ◽  
Author(s):  
Dao Bing Huang ◽  
Yuan Qiang Tu ◽  
Ting Hu ◽  
Guang Ling Song ◽  
Xing Peng Guo
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Polarization Curve ◽  
Potentiodynamic Polarization ◽  
Electrochemical Behavior ◽  
Electrochemical Impedance ◽  
Potentiodynamic Polarization Curve

The electrochemical behavior of pure Mg in H3PO4 acid (0.42 M) and phosphating solution (0.42 M H3PO4+0.34 M ZnO) was investigated through electrochemical impedance spectroscopy (EIS), potentiodynamic polarization curve and XRD measurements. The results show that Mg has higher corrosion resistance in the phosphating solution than that in the H3PO4 acid which may be due to the relative protective phosphating film on the surface.

Electrochemical Impedance Spectroscopy (EIS) Study of Nano-Composite Polyurea Coating under the Wet-Dry Cyclic Conditions

2014 ◽  
Vol 789 ◽  
pp. 495-500
Author(s):  
Bing Ying Wang ◽  
Qing Hao Shi ◽  
Wen Long Zhang
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Composite Coating ◽  
Electrochemical Impedance ◽  
Protective Action ◽  
Experimental Result ◽  
Resistance Property ◽  
Corrosion Resistance Property ◽  
Mass Fractions

The polyurea was modified by adding different amounts of nanometer ZnO. The corrosion behavior of polyurea/primer composite coating system in wet-dry cyclic environment of 3.5% NaCl solution was studied by using the Electrochemical Impedance Spectroscopy (EIS) measurement and adhesion test technology. The experimental result showed that, different mass fractions of nanometer ZnO had different influences on the corrosion resistance property of coating. When the mass fraction of nanometer ZnO was 5%, the composite coating had the largest protective action. The corrosion resistance property of nanometer ZnO can be improved by increasing the density of polyurea coating, however, the corrosion resistance property of polyurea coating will be weakened in case of exceeding the critical adding amount.

The effect of electroplating current density on microstructure, corrosion, and wear behavior of Ni–P–W–TiO2 coating

2021 ◽  
Vol 112 (6) ◽  
pp. 474-485
Author(s):  
Sajjad Sadeghi ◽  
Hadi Ebrahimifar
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Current Density ◽  
Potentiodynamic Polarization ◽  
Electrochemical Impedance ◽  
Wear Behavior ◽  
Micro Hardness ◽  
Aisi 304L

Abstract The use of ceramic particles in the matrix of alloy coatings during the electroplating process has received considerable attention. These particles can create properties such as high corrosion resistance, insolubility, high-temperature stability, strong hardness, and self-lubrication capability. Herein, an Ni–P–W–TiO2 coating was deposited on an AISI 304L steel substrate using the electroplating method. Electroplating was performed at current densities of 10, 15, 20, and 25 mA · cm–2, and the effect of current density on microstructure, corrosion behavior, and wear behavior was investigated. The coatings were characterized by means of scanning electron microscopy. To investigate corrosion resistance, potentiodynamic polarization and electrochemical impedance spectroscopy tests were performed in a 3.5% NaCl aqueous solution. A pin-on-disk test was conducted to test the wear resistance of uncoated and coated samples. Sample micro-hardness was also measured by Vickers hardness testing. Examination of the microstructure revealed that the best coating was produced at a current density of 20 mA · cm–2. The results of potentiodynamic polarization and electrochemical impedance spectroscopy tests were consistent with microscopic images. The coating created at the current density of 20 mA · cm–2 had the highest corrosion resistance compared to other coated and non-coated samples. Furthermore, the results of the wear test showed that increasing the current density of the electroplating path up to 20 mA · cm–2 enhances micro-hardness and wear resistance.

Corrosion Resistance of a New Cu-Alloy (Low Ni) vis-à-vis Cu-10Ni Alloy in Sulfide Polluted Synthetic Seawater

2012 ◽  
Vol 585 ◽  
pp. 488-492
Author(s):  
Adeeba F. Khan ◽  
Awanikumar P. Patil ◽  
T. Subba Rao
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Impedance Spectroscopy ◽  
Electrochemical Impedance ◽  
Accelerated Corrosion ◽  
Synthetic Seawater ◽  
Cu Alloy

Cu-10Ni alloy suffers accelerated corrosion in sulfide polluted seawater. As an alternative, a new single phased, Cu-28%Zn-5%Ni-5%Mn-2%Fe alloy (hereby referred as CNZ-alloy) is developed and tested for the corrosion resistance in clean and sulfide polluted synthetic seawater. The CNZ-alloy showed better corrosion resistance than the standard Cu-10Ni alloy in both the test solutions i.e. clean and sulfide polluted synthetic seawater with . The results are discussed on the basis of polarization and electrochemical impedance spectroscopy. The better corrosion resistance of CNZ-alloy is attributed to the formation of protective ZnS and MnS2 films.

scholarly journals Nano-TiO2 Phosphate Conversion Coatings – A Chemical Approach

2018 ◽  
Vol 4 (1) ◽  
pp. 47-54 ◽  
Author(s):  
Nilesh S. Bagal ◽  
Vaibhav S. Kathavate ◽  
Pravin P. Deshpande
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance Spectroscopy ◽  
Carbon Steel ◽  
Impedance Spectroscopy ◽  
Zinc Phosphate ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Phosphate Coatings ◽  
Coating Weight

AbstractThe present study aims at deposition of zinc phosphate coatings on low carbon steel with incorporated nano- TiO2 particles by chemical phosphating method. The coated low carbon steel samples were assessed in corrosion studies using electrochemical impedance spectroscopy and potentiodynamic polarization techniques (Tafel) in 3.5% NaCl solution. Morphology and chemical composition of the coatings were analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy in order to observe growth of coating. Significant variations in the coating weight, porosity and corrosion resistance were observed with the addition of nano- TiO2 in the phosphating bath. Corrosion rate of nano-TiO2 chemical phosphate coated samples was found to be 3.5 milli inches per year which was 3 times less than the normal phosphate-coated sample (8 mpy). Electrochemical impedance spectroscopy studies reveal reduction of porosity of nano-TiO2 phosphate coated samples. It was found that nano-TiO2 particles in the phosphating solution yielded uniform phosphate coatings of higher coating weight, fewer defects and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal phosphating bath).

Sign in / Sign up

Export Citation Format

Share Document