Effect of surface texture on the mechanical performance of bonded joints: a review

2021 ◽  
pp. 1-93
Author(s):  
Nidhal Naat ◽  
Yasmina Boutar ◽  
Sami Naïmi ◽  
Salah Mezlini ◽  
Lucas Filipe Martins Da Silva
Keyword(s):  
Surface Texture ◽  
Mechanical Performance ◽  
Bonded Joints ◽  
Effect Of Surface

Effect of surface texture and working gap on the braking performance of the magnetorheological fluid brake

2016 ◽  
Vol 25 (10) ◽  
pp. 105026 ◽  
Author(s):  
Na Wang ◽  
Dong Heng Li ◽  
Wan Li Song ◽  
Shi Chao Xiu ◽  
Xiang Zhi Meng
Keyword(s):  
Surface Texture ◽  
Magnetorheological Fluid ◽  
Braking Performance ◽  
Effect Of Surface

scholarly journals Bio-inspired design of ice-retardant devices based on benthic marine invertebrates: the effect of surface texture

2014 ◽  
Author(s):  
Homayun Mehrabani ◽  
Neil Ray ◽  
Kyle Tse ◽  
Dennis Evangelista
Keyword(s):  
Surface Texture ◽  
Marine Invertebrates ◽  
Freezing Point ◽  
Three Dimensional ◽  
Surface Pattern ◽  
Ice Formation ◽  
Cold Air ◽  
Three Dimensional Printing ◽  
Species Specific ◽  
Effect Of Surface

Growth of ice on surfaces poses a challenge for both organisms and for devices that come into contact with liquids below the freezing point. Resistance of some organisms to ice formation and growth, either in subtidal environments (e.g. Antarctic anchor ice), or in environments with moisture and cold air (e.g.vplants, intertidal) begs examination of how this is accomplished. Several factors may be important in promoting or mitigating ice formation. As a start, here we examine the effect of surface texture alone. We tested four candidate surfaces, inspired by hard-shelled marine invertebrates and constructed using a three-dimensional printing process. We screened biological and artifical samples for ice formation and accretion in submerged conditions using previous methods, and developed a new test to examine ice formation from surface droplets as might be encountered in environments with moist, cold air. It appears surface texture plays only a small role in delaying the onset of ice formation: a stripe feature (corresponding to patterning found on valves of blue mussels,Crassostrea gigas, or on the spines of the Antarctic sea urchinSterechinus neumayeri) slowed ice formation an average of 25% compared to a grid feature (corresponding to patterning found on sub-polar butterclams,Saxidomas nuttali). The geometric dimensions of the features have only a small (~6%) effect on ice formation. Surface texture affects ice formation, but does not explain by itself the large variation in ice formation and species-specific ice resistance observed in other work. This suggests future examination of other factors, such as material elastic properties and coatings, and their interaction with surface pattern.

High Definition Metrology-Based Quality Improvement of Surface Texture in Face Milling of Workpieces with Discontinuous Surfaces

2021 ◽  
pp. 1-38
Author(s):  
Guilong Li ◽  
Shichang Du ◽  
Bo Wang ◽  
Jun Lv ◽  
Yafei Deng
Keyword(s):  
Quality Improvement ◽  
Surface Texture ◽  
Mechanical Performance ◽  
Processing Parameters ◽  
Milling Process ◽  
Face Milling ◽  
Measurement Instruments ◽  
High Definition ◽  
Tool Marks

Abstract In face milling process, the quality of surface texture is vital for mechanical performance of workpieces. The quality of surface texture, especially for waviness, is directly affected by tool marks, a commonly observed phenomenon in face milling. However, appropriate approaches for evaluation and modeling of tool marks are absent to date. Limited to the resolution as well as the efficiency of conventional measurement instruments, the height data of tool marks is hard to be entirely obtained, leading to valuable information omission. Besides, most existing models of tool marks are established for general workpieces with regular geometry and continuous surfaces. Since the cutter-workpiece engagement mode has a significant impact on the generation of tool marks, current models could be inaccurate or invalid when dealing with workpieces with discontinuous surfaces. To overcome this shortage, a novel approach is proposed in this paper, aimed at quality improvement of surface texture in face milling of workpieces with discontinuous surfaces. Firstly, the evaluation indexes for tool marks are defined based on the recently developed high definition metrology (HDM). Secondly, the physical modeling of tool marks is presented, taking the face milling mechanism into account. Thirdly, the physical-informed optimization model is developed to search for the optimal processing parameters for surface quality improvement. At last, the effectiveness of the proposed approach is verified by a face milling experiment on the engine blocks.

scholarly journals An Experimental Study on the Effect of Surface Texture on Contact Stiffness Using Soft Material

2018 ◽  
Vol 217 ◽  
pp. 02005
Author(s):  
Z. Fuadi
Keyword(s):  
Surface Texture ◽  
Normal Load ◽  
Contact Stiffness ◽  
Soft Material ◽  
Contact Dynamics ◽  
Real Contact Area ◽  
Textured Surfaces ◽  
Indentation Force ◽  
Result Show ◽  
Effect Of Surface

Contact interface is one of the most important factors in a mechanical contact because it is the place where friction, sound, and heat originate. It is therefore inevitable that modeling various phenomenon related to contact dynamics requires a proper representation of the contact interfaces. One of the methods in representing the behavior of two surfaces in contact is by using the parameter of contact stiffness. In this study, the effect of surface texture on contact stiffness is analyzed. the texture was used in order to reduce the randomness of surface roughness. the soft material was chosen to achieve a pure elastic contact thus preventing plastic deformation to the asperities. the analysis was conducted by using an indentation method employing a steel ball with a relatively small indentation force. the result show contact stiffness values of the textured surfaces were smaller than that of smooth surface. This is particularly observed at low normal load at which total deformation of the surface is relatively small compared to the asperities height. This decrease in the contact stiffness value of the textured surfaces can be related to the reduction in the real contact area.

Sign in / Sign up

Export Citation Format

Share Document