Modifying the steel surface by laser heating

2016 ◽  
Vol 31 (3) ◽  
pp. 233-237 ◽  
Author(s):  
O. V. Chudina
Keyword(s):  
2021 ◽  
Vol 2064 (1) ◽  
pp. 012102
Author(s):  
U L Mishigdorzhiyn ◽  
N S Ulakhanov ◽  
A V Nomoev ◽  
A B Lupsanov

Abstract The paper deals with a new application solution of Ytterbium Picosecond Pulsed Fiber Laser for surface modification of 3Kh2V8F hot-work tool steel (the analog of AISI H21 steel). Surface modification was conducted by B4C-Al powders from preplaced pastes followed by laser heating. The ratio of B4C-Al powders was taken as 5/1 by weight and the paste thickness was approximately 1 mm. Laser treatment was conducted according to the following parameters: 1070 nm of wavelength, 100 W of power, 1 mJ of pulse energy, 100 ns pulse duration, pulse frequency range from 50 kHz to 90 kHz. Several tracks with different widths were obtained as a result of treatment depending on velocity of the laser move. EDS analysis showed that B4C particles were not completely dissolved in the weld beads. However, an enhanced concentration of boron (8-12 wt.%) was revealed in the vicinity of B4C particles. The aluminum concentration was low (up to 0.79 wt.%) on the surface of the weld beads.


Author(s):  
E Y. Wang ◽  
J. T. Cherian ◽  
A. Madsen ◽  
R. M. Fisher

Many steel parts are electro-plated with chromium to protect them against corrosion and to improve their wear-resistance. Good adhesion of the chrome plate to the steel surface, which is essential for long term durability of the part, is extremely dependent on surface preparation prior to plating. Recently, McDonnell Douglas developed a new pre-treatment method for chrome plating in which the steel is anodically etched in a sulfuric acid and hydrofluoric acid solution. On carbon steel surfaces, this anodic pre-treatment produces a dark, loosely adhering material that is commonly called the “smut” layer. On stainless steels and nickel alloys, the surface is only darkened by the anodic pre-treatment and little residue is produced. Anodic pre-treatment prior to hard chrome plating results in much better adherence to both carbon and alloy steels.We have characterized the anodic pre-treated steel surface and the resulting “smut” layer using various techniques including electron spectroscopy for chemical analysis (ESCA) on bulk samples and transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS) on stripped films.


2020 ◽  
Vol 82 (5) ◽  
pp. 11-20
Author(s):  
D.R. Abdulina ◽  
◽  
L.M. Purish ◽  
G.O. Iutynska ◽  
◽  
...  

The studies of the carbohydrate composition of the sulfate-reducing bacteria (SRB) biofilms formed on the steel surface, which are a factor of microbial corrosion, are significant. Since exopolymers synthesized by bacteria could activate corrosive processes. The aim of the study was to investigate the specificity of commercial lectins, labeled with colloidal gold to carbohydrates in the biofilm exopolymeric matrix produced by the corrosive-relevant SRB strains from man-caused ecotopes. Methods. Microbiological methods (obtaining of the SRB biofilms during cultivation in liquid Postgate B media under microaerophilic conditions), biochemical methods (lectin-binding analysis of 10 commercial lectins, labeled with colloidal gold), transmission electron microscopy using JEM-1400 JEOL. Results. It was shown using transmission electron microscopy that the binding of lectins with carbohydrates in the biofilm of the studied SRB strains occurred directly in the exopolymerіс matrix, as well as on the surfaces of bacterial cells, as seen by the presence of colloidal gold particles. For detection of the neutral carbohydrates (D-glucose and D-mannose) in the biofilm of almost all studied bacterial strains PSA lectin was the most specific. This lectin binding in biofilms of Desulfotomaculum sp. К1/3 and Desulfovibrio sp. 10 strains was higher in 90.8% and 94.4%, respectively, then for ConA lectin. The presence of fucose in the SRB biofilms was detected using LABA lectin, that showed specificity to the biofilm EPS of all the studied strains. LBA lectin was the most specific to N-аcetyl-D-galactosamine for determination of amino sugars in the biofilm. The amount of this lectin binding in D. vulgaris DSM644 biofilm was 30.3, 10.1 and 9.3 times higher than SBA, SNA and PNA lectins, respectively. STA, LVA and WGA lectins were used to detect the N-acetyl-Dglucosamine and sialic acid in the biofilm. WGA lectin showed specificity to N-acetyl-D-glucosamine in the biofilm of all the studied SRB; maximum number of bounded colloidal gold particles (175 particles/μm2) was found in the Desulfotomaculum sp. TC3 biofilm. STA lectin was interacted most actively with N-acetyl-D-glucosamine in Desulfotomaculum sp. TC3 and Desulfomicrobium sp. TC4 biofilms. The number of bounded colloidal gold particles was in 9.2 and 7.4 times higher, respectively, than using LVA lectin. The lowest binding of colloidal gold particles was observed for LVA lectin. Conclusions. It was identified the individual specificity of the 10 commercial lectins to the carbohydrates of biofilm matrix on the steel surface, produced by SRB. It was estimated that lectins with identical carbohydrates specificity had variation in binding to the biofilm carbohydrates of different SRB strains. Establishing of the lectin range selected for each culture lead to the reduction of the scope of studies and labor time in the researching of the peculiarities of exopolymeric matrix composition of biofilms formed by corrosiverelevant SRB.


Author(s):  
A. H. Sari ◽  
Valiantsin M. Astashynski ◽  
E. A. Kostyukevich ◽  
A. M. Kuzmitski ◽  
V. V. Uglov ◽  
...  

Author(s):  
Nikolai N. Cherenda ◽  
Vladimir V. Uglov ◽  
Yu. V. Martinovich ◽  
I. A. Betanov ◽  
Valiantsin M. Astashynski ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document