Optimal reinforcement framework for distribution system based on life cycle cost and considering uncertainties

2020 ◽  
Vol 39 (8) ◽  
pp. 804-821
Author(s):  
V. V. Thang
Author(s):  
Alina Galimshina ◽  
Maliki Moustapha ◽  
Alexander Hollberg ◽  
Guy Wagner ◽  
Pierryves Padey ◽  
...  

Renovation of the building stock in Europe is urgent to decrease the environmental impact from the building sector and meet the United Nations climate action goals. However, it is often hard to define a robust scenario for a renovation due to numerous uncertainties, which occur during the production, operation and end-of-life stage. One can cite the loss of performance of insulation and heating systems, the replacement time of installation or the future energy prices as well as the future climate. The replacement of oil boilers with heat pumps has shown a good performance regarding costs and greenhouse gas emissions. However, due to the flow and return temperature differences, often the current heat distribution system needs to be replaced as well, which is normally done with conventional radiators or floor heating. In this paper, we analyse a new possibility of a heat distribution system with earth plastered wall. We develop a methodology on the integrated assessment of life cycle assessment (LCA) and life cycle cost analysis (LCCA) for the renovation scenarios and adapt the analysis of the heat pump renovation solution with conventional radiators system and the earth plastered wall for two typical residential buildings located in Switzerland. Through rigorous statistical treatment, we then propagate the possible sources of uncertainty and perform the uncertainty quantification using polynomial chaos expansion to compare the distributions of two outcomes. The results show that the solution with the earth plaster has lower overall environmental impacts and costs. It has also been noticed that the solution with the earth plaster is more robust in investment cost and embodied emissions compared to the solution with the conventional radiators.


2017 ◽  
Vol 11 (1) ◽  
pp. 165-176 ◽  
Author(s):  
V. V. Thang ◽  
N. D. Minh

Background:The power and voltage losses have been greatly concerned in the distribution system planning and operation because low normal voltage, high impedance and load density of the system lead to increases in losses and decreases in bus voltages.Method:Therefore, an optimization model for the distribution system reinforcement improving efficiency of distribution systems by integrating capacitors is proposed. The optimal allocation and sizing of capacitors are determined concurrently with optimal upgrading sizing and timeframe of feeders and substations. The objective function of model is to minimize life cycle cost over reinforcement scheme including investment and operation costs of equipment in distribution systems (including feeders, substations and capacitors) and costs for purchasing energy from the electric market.Conclusion:The typical load curves for each day and season with uncertainties modeled by a Probability Distribution Function (PDF) and Time of Use (TOU) price applied to enhance accuracy of calculation results and suitability for real operation conditions. General Algebraic Modeling System (GAMS) is applied to undertake calculations in a test system.


1994 ◽  
Vol 11 (1) ◽  
pp. 47-56
Author(s):  
Virginia C. Day ◽  
Zachary F. Lansdowne ◽  
Richard A Moynihan ◽  
John A. Vitkevich

2011 ◽  
Vol 4 (5) ◽  
pp. 158-161 ◽  
Author(s):  
A. Morfonios A. Morfonios ◽  
◽  
D. Kaitelidou D. Kaitelidou ◽  
G. Filntisis G. Filntisis ◽  
G. Baltopoulos G. Baltopoulos ◽  
...  

2014 ◽  
Vol 4 (3) ◽  
pp. 1-9
Author(s):  
Badrinarayan Rath ◽  
◽  
Shirish Deo ◽  
Gangadhar Ramtekkar ◽  
◽  
...  

Alloy Digest ◽  
1997 ◽  
Vol 46 (5) ◽  

Abstract Duracorr is low-cost, utilitarian 11% Cr stainless steel with more corrosion resistance and life-cycle cost advantages than weathering steels. The steel may be used where a combination of abrasion and corrosion resistance is required. This datasheet provides information on composition, physical properties, microstructure, hardness, tensile properties, and bend strength as well as fracture toughness. It also includes information on corrosion resistance as well as joining. Filing Code: SS-680. Producer or source: Lukens Steel Company.


Sign in / Sign up

Export Citation Format

Share Document