Modeling the size of small spills of pure volatile liquids for use in evaporation rate and air concentration modeling

2020 ◽  
Vol 17 (7-8) ◽  
pp. 325-333
Author(s):  
Chris Keil ◽  
Grant Miller
Keyword(s):  
Evaporation Rate ◽  
Air Concentration ◽  
Volatile Liquids

scholarly journals Sessile volatile drop evaporation under microgravity

2020 ◽  
Vol 6 (1) ◽  
Author(s):  
Sanjeev Kumar ◽  
Marc Medale ◽  
Paolo Di Marco ◽  
David Brutin
Keyword(s):  
Evaporation Rate ◽  
Sessile Drop ◽  
Experimental Results ◽  
Sounding Rocket ◽  
Critical Height ◽  
Drop Evaporation ◽  
Capillary Instabilities ◽  
Volatile Liquids ◽  
Drop Interface ◽  
Sessile Drops

AbstractThe evaporation of sessile drops of various volatile and non-volatile liquids, and their internal flow patterns with or without instabilities have been the subject of many investigations. The current experiment is a preparatory one for a space experiment planned to be installed in the European Drawer Rack 2 (EDR-2) of the International Space Station (ISS), to investigate drop evaporation in weightlessness. In this work, we concentrate on preliminary experimental results for the evaporation of hydrofluoroether (HFE-7100) sessile drops in a sounding rocket that has been performed in the frame of the MASER-14 Sounding Rocket Campaign, providing the science team with the opportunity to test the module and perform the experiment in microgravity for six consecutive minutes. The focus is on the evaporation rate, experimentally observed thermo-capillary instabilities, and the de-pinning process. The experimental results provide evidence for the relationship between thermo-capillary instabilities and the measured critical height of the sessile drop interface. There is also evidence of the effects of microgravity and Earth conditions on the sessile drop evaporation rate, and the shape of the sessile drop interface and its influence on the de-pinning process.

Hole Formation in Gold Films

1972 ◽  
Vol 30 ◽  
pp. 510-511
Author(s):  
R. W. Vook ◽  
R. Cook ◽  
R. Ziemer
Keyword(s):  
Deposition Rate ◽  
Quartz Crystal ◽  
Evaporation Rate ◽  
Gold Films ◽  
Hole Density ◽  
Hole Formation ◽  
Microscope Slide ◽  
Crystal Film ◽  
Glass Microscope Slide ◽  
Glass Microscope

During recent experiments on Au films, a qualitative correlation between hole formation and deposition rate was observed. These early studies were concerned with films 80 to 1000A thick deposited on glass at -185°C and annealed at 170°C. In the present studies this earlier work was made quantitative. Deposition rates varying between 5 and 700 A/min were used. The effects of deposition rate on hole density for two films 300 and 700A thick were investigated.Au was evaporated from an outgassed W filament located 10 cm from a glass microscope slide substrate and a quartz crystal film thickness monitor. A shutter separating the filament from the substrate and monitor made it possible to obtain a constant evaporation rate before initiating deposition. The pressure was reduced to less than 1 x 10-6 torr prior to cooling the substrate with liquid nitrogen. The substrate was cooled in 15 minutes during which the pressure continued to drop to the mid 10-7 torr range, where deposition was begun.

WATER DROPLET EVAPORATION IN A CHAMBER ISOLATED FROM THE EXTERNAL ENVIRONMENT

2020 ◽  
Vol 6 (3) ◽  
pp. 8-22
Author(s):  
KSENIA A. Batishcheva ◽  
ATLANT E. Nurpeiis
Keyword(s):  
Water Vapor ◽  
Evaporation Rate ◽  
External Environment ◽  
Heat Removal ◽  
Droplet Evaporation ◽  
Droplet Volume ◽  
Evaporation Time ◽  
Aluminum Alloy Amg6 ◽  
Evaporation Of Droplets ◽  
Contact Diameter

With an increase in the productivity of power equipment and the miniaturization of its components, the use of traditional thermal management systems becomes insufficient. There is a need to develop drip heat removal systems, based on phase transition effects. Cooling with small volumes of liquids is a promising technology for microfluidic devices or evaporation chambers, which are self-regulating systems isolated from the external environment. However, the heat removal during evaporation of droplets into a limited volume is a difficult task due to the temperature difference in the cooling device and the concentration of water vapor that is unsteady in time depending on the mass of the evaporated liquid. This paper presents the results of an experimental study of the distilled water microdrops’ (5-25 μl) evaporation on an aluminum alloy AMg6 with the temperatures of 298-353 K in an isolated chamber (70 × 70 × 30 mm3) in the presence of heat supply to its lower part. Based on the analysis of shadow images, the changes in the geometric dimensions of evaporating drops were established. They included the increase in the contact diameter, engagement of the contact line due to nano roughening and chemical composition inhomogeneous on the surface (90-95% of the total evaporation time) of the alloy and a decrease in the contact diameter. The surface temperature and droplet volume did not affect the sequence of changes in the geometric dimensions of the droplets. It was found that the droplet volume has a significant effect on the evaporation time at relatively low substrate temperatures. The results of the analysis of droplet evaporation rates and hygrometer readings have shown that reservoirs with salt solutions can be used in isolated chambers to control the concentration of water vapor. The water droplets evaporation time was determined. The analysis of the time dependences of the evaporation rate has revealed that upon the evaporation of droplets in an isolated chamber under the conditions of the present experiment, the air was not saturated with water vapor. The latter did not affect the evaporation rate.

scholarly journals Highly efficient evaporative cooling by all-day water evaporation using hierarchically porous biomass

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jihun Choi ◽  
Hansol Lee ◽  
Bokyeong Sohn ◽  
Minjae Song ◽  
Sangmin Jeon
Keyword(s):  
Porous Structure ◽  
Fiber Length ◽  
Evaporation Rate ◽  
Water Evaporation ◽  
Thickness Direction ◽  
Hierarchically Porous ◽  
Hierarchically Porous Structure ◽  
Length Direction ◽  
Luffa Sponge ◽  
Fiber Thickness

AbstractWe developed a 3D solar steam generator with the highest evaporation rate reported so far using a carbonized luffa sponge (CLS). The luffa sponge consisted of entangled fibers with a hierarchically porous structure; macropores between fibers, micro-sized pores in the fiber-thickness direction, and microchannels in the fiber-length direction. This structure remained after carbonization and played an important role in water transport. When the CLS was placed in the water, the microchannels in the fiber-length direction transported water to the top surface of the CLS by capillary action, and the micro-sized pores in the fiber-thickness direction delivered water to the entire fiber surface. The water evaporation rate under 1-sun illumination was 3.7 kg/m2/h, which increased to 14.5 kg/m2/h under 2 m/s wind that corresponded to the highest evaporation rate ever reported under the same condition. The high evaporation performance of the CLS was attributed to its hierarchically porous structure. In addition, it was found that the air temperature dropped by 3.6 °C when the wind passed through the CLS because of the absorption of the latent heat of vaporization. The heat absorbed by the CLS during water evaporation was calculated to be 9.7 kW/m2 under 1-sun illumination and 2 m/s wind, which was 10 times higher than the solar energy irradiated on the same area (1 kW/m2).

Sign in / Sign up

Export Citation Format

Share Document