scholarly journals Development of antibacterial composite resin containing chitosan/fluoride microparticles as pit and fissure sealant to prevent caries

2021 ◽  
Vol 14 (1) ◽  
Author(s):  
Chun-Cheng Lai ◽  
Chun-Pin Lin ◽  
Yin-Lin Wang
Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1535 ◽  
Author(s):  
Li ◽  
Tsai ◽  
Fang ◽  
Wang ◽  
Lin ◽  
...  

Molar pits and fissures tend to be affected by caries due to cleaning difficulties. As such, the filling of pits and cracks with sealants is common to deter the onset of caries. However, current clinical practices rely on sealants that lack the ability to release and recharge fluoride ions. Thus, we herein report the development of a fluoride—montmorillonite nanocomposite resin that has the potential to provide sustained release of fluoride due to the strong adsorption of fluoride by montmorillonite. X-ray diffractometry, thermogravimetric analysis, and Fourier-transform infrared spectroscopy were employed to confirm the successful insertion of the polymer into the interlayer structure. The mechanical properties (viscosity, hardening depth, hardness, diametral tensile strength, flexural strength, and wear resistance) of the developed composite resin were then examined, and simulation of the oral environment demonstrated a good fluoride ion release and recharge ability for the effective prevention of dental caries. Finally, we demonstrated the non-cytotoxic nature of this material using the water-soluble tetrazolium salt (WST-1) test. We expect that the described fluoride-containing composite resin may become a new clinical option in the near future.


2018 ◽  
Vol 43 (3) ◽  
pp. 88-93
Author(s):  
Nour M. Owida ◽  
Nadia A. Wahba ◽  
Dalia M. Talaat ◽  
Bassem F. Elmallakh

Children ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 444
Author(s):  
Rahif E. Mattar ◽  
Ayman M. Sulimany ◽  
Saad S. Binsaleh ◽  
Ibrahim M. Al-Majed

This randomized clinical trial aimed to evaluate the patient’s preference and chair time needed during pit and fissure sealant placement under three isolation techniques (Isolite system, rubber dam isolation, and cotton roll isolation). Participants, aged 6–15 years and requiring four sealants on the first or second permanent molars, attending the pediatric dental clinics at King Saud University in Saudi Arabia were enrolled according to the inclusion criteria. Each participant received sealants on three random first or second permanent molars using three isolation techniques. The time required for sealant placement was recorded for each technique. Following sealant placement, an interview-based questionnaire was administered to the participants to evaluate their preference regarding the isolation techniques. Forty-eight children (23 male and 25 female) with a mean age of 8.58 ± 1.93 years participated in this study. The mean chair times were 248.14, 255.89, and 243.29 s for the Isolite system, rubber dam isolation, and cotton roll isolation, respectively. Approximately 79% of participants considered cotton roll isolation to be the most comfortable, whereas approximately 71% were significantly less likely to use rubber dam isolation again. In conclusion, there were no significant differences in sealant placement time among the three isolation techniques. However, cotton roll isolation was the technique that was most preferred by the participants.


2004 ◽  
Vol 12 (3) ◽  
pp. 200-204 ◽  
Author(s):  
Gisele Maria Correr ◽  
Angela S. Caldo-Teixeira ◽  
Roberta Caroline Bruschi Alonso ◽  
Regina Maria Puppin-Rontani ◽  
Mário Alexandre Coelho Sinhoreti ◽  
...  

The aim of this study was to evaluate the effect of saliva contamination (SCT) and re-etching time (RET) on the shear bond strength (SBS) of the Fluroshield sealant. Forty-five extracted third molars were sectioned and flattened until reach an enamel surface area. Then, all samples were etched for 30 sec with 35% phosphoric acid and then they were distributed into 9 groups (n=10) according to SCT and RET (seconds), respectively: G1- control (no SCT and no RET); G2- 30s and 0s; G3- 60s and 0s; G4-30s and 2s; G5- 30s and 5s; G6- 30s and 15s; G7-60s and 2s; G8- 60s and 5s; G9- 60s and 15s. The sealant was applied according to the manufacturer's instructions. The samples were stored in distilled water at 37ºC for 72h and subjected to the SBS test. The results indicated that there was no statistically significant difference between the groups (p>0.05). However, it could be noticed that: 1- the longer the SCT, the lower the SBS values; 2 - the longer the RET, the higher the SBS values. It could be concluded that there was a tendency to the shortest SCT (30s) associated to the longest RET (5 and 15s) to reach similar SBS values for the control group.


Sign in / Sign up

Export Citation Format

Share Document