scholarly journals Determining the Depth of Local Scouring in a Downstream Energy Dissipation in the Physical Model Test

2021 ◽  
Vol 930 (1) ◽  
pp. 012022
Author(s):  
R D Lufira’ ◽  
S Marsudi ◽  
S Agustien ◽  
A Khosin
Keyword(s):  
Energy Dissipation ◽  
Physical Model ◽  
Model Test ◽  
Design Model ◽  
Physical Model Test ◽  
Original Design ◽  
Physical Model Tests ◽  
Final Design ◽  
Concrete Blocks ◽  
River Bottom

Abstract Karangnongko Weir is planned to be located in the Bengawan Solo River (Lower Solo River Basin) about 15 km downstream of the confluence of Bengawan Solo River with the Madiun River in Ngelo Village, Margomulyo Sub-District, Bojonegoro Regency, and Ngrawoh Village in Kradenan Sub-District, Blora Regency. This study aims to determine the Depth and pattern of scouring in downstream energy dissipation through physical model tests based on initial planning. Downstream protection of energy dissipation in the original design model combines 50 m of riprap rocks and 50 m of riprap concrete for a total length of 100 m of protection. The maximum scouring pattern occurred at elevation + 17.64 m, where the scouring was 4.36 m deep, from the planned essential height of Height 00 m. Thus, the downstream protection of energy dissipation was extended to 112 m in riprap concrete blocks for the final design model. Scouring at the end of riprap was 3.04 m, the original elevation of the river bottom of + 22.00 m, down to + 18.96 m. It is concluded that the protection is effective in reducing scouring by up to 30.27%.

Stress densification and its evaluation

2004 ◽  
Vol 41 (1) ◽  
pp. 181-186 ◽  
Author(s):  
Sung-Sik Park ◽  
Peter M Byrne
Keyword(s):  
Physical Model ◽  
Applied Stress ◽  
Test Data ◽  
Model Test ◽  
Physical Model Test ◽  
Liquefaction Resistance ◽  
Physical Test ◽  
One Dimensional ◽  
Physical Model Tests ◽  
Stress Changes

Stress densification occurs in natural soils as well as manmade embankments and physical model tests. Such densification can increase stability and liquefaction resistance. One-dimensional compression test data from eight sands were examined. From these data a stress densification equation is developed to estimate the density increase due to applied stress changes. It is found that stress densification can lead to erroneous conclusions if not taken into consideration when evaluating physical model test results.Key words: stress, densification, embankments, physical test.

scholarly journals STABILITY OF XBLOCPLUS ARMOUR LAYERS AFTER INITIAL DAMAGE

2020 ◽  
pp. 16
Author(s):  
Pieter Bakker ◽  
Tiemen de Hoop ◽  
Markus Muttray
Keyword(s):  
Physical Model ◽  
Model Test ◽  
Safety Margin ◽  
Single Layer ◽  
Physical Model Test ◽  
Stability Number ◽  
Random Orientation ◽  
Initial Damage ◽  
Physical Model Tests ◽  
Hydraulic Stability

XblocPlus is an interlocking single layer armour unit that is placed with uniform orientation. The unit is applied with a large safety margin. Physical model test were performed without damage up to stability numbers of Hs/dDn=5.5 whereas a design stability number of Hs/dDn=2.5 has been adopted. The behaviour of an XblocPlus armour layer after initial damage is has been investigated by physical model tests with broken and manually removed model units. XblocPlus armour layers (with uniform orientation) respond differently to initial damage than interlocking armour units with random orientation. The latter are moving and re-arranging in order to bridge a gap in the armour layer (de Rover et al., 2008). XblocPlus units in contrast hardly move and nonetheless maintain the hydraulic stability of the damaged section. Details of the experiments and findings as well as implications for design and maintenance of breakwater armour layers will be discussed in the final paper.Recorded Presentation from the vICCE (YouTube Link): https://youtu.be/izwm60IBx-4

Model Test Study on Influences of Layered Rock Mass Dip Angle on Stability of Deep-Buried Tunnel

2011 ◽  
Vol 90-93 ◽  
pp. 2363-2371
Author(s):  
Bin Wei Xia ◽  
Ke Hu ◽  
Yi Yu Lu ◽  
Dan Li ◽  
Zu Yong Zhou
Keyword(s):  
Rock Mass ◽  
Physical Model ◽  
Model Test ◽  
Physical Models ◽  
Physical Model Test ◽  
Stress Distributions ◽  
Failure Characteristics ◽  
Layered Rock ◽  
Layered Rock Mass ◽  
Dip Angle

Physical models of layered rock mass with different dip angles are built by physical model test in accordance with the bias failure characteristics of surrounding rocks of layered rock mass in Gonghe Tunnel. Bias failure characteristics of surrounding rocks in thin-layered rock mass and influences of layered rock mass dip angle on stability of tunnel are studied. The research results show that failure characteristics of physical models generally coincide with those of surrounding rocks monitored from the tunnel site. The failure regions of surrounding rock perpendicular to the stratification planes are obviously larger than those parallel to. The stress distributions and failure characteristics in the surrounding rocks are similar to each physical model of different dip angles. The stress distributions and failure regions are all elliptic in shape, in which the major axis is in the direction perpendicular to the stratification planes while the minor axis is parallel to them. As a result, obvious bias failure of surrounding rocks has gradually formed. The physical model tests provide reliable basis for theoretical analysis on the failure mechanism of deep-buried layered rock mass.

scholarly journals An Improved Empirical Model for Flood Discharge Atomization and Its Application to Optimize the Flip Bucket of the Nazixia Project

2019 ◽  
Vol 16 (3) ◽  
pp. 316 ◽  
Author(s):  
Jijian Lian ◽  
Junling He ◽  
Fang Liu ◽  
Danjie Ran ◽  
Xiaoqun Wang ◽  
...  
Keyword(s):  
Physical Model ◽  
Model Test ◽  
Empirical Model ◽  
Rainfall Intensity ◽  
Droplet Diameter ◽  
Heavy Rain ◽  
Physical Model Test ◽  
Rain Area ◽  
Left Wall ◽  
Flood Discharge

Flood discharge atomization is a serious challenge that threatens the daily lives of the residents around the dam area as well as the safety of the water conservancy project. This research aims to improve the prediction accuracy of the stochastic splash model. A physical model test with four types of flip bucket is conducted to obtain the hydraulic parameters of the impinging outer edge of the water jet, the relationship of the splashing droplet diameter with its corresponding velocity, and the spatial distribution of the downstream nappe wind. The factors mentioned above are introduced to formulate the empirical model. The rule obtained from the numerical analyses is compared with the results of the physical model test and the prototype observations, which yields a solid agreement. The numerical results indicate that the powerhouse is no longer in the heavy rain area when adopting the flip bucket whose curved surface is attached to the left wall. The rainfall intensity of the powerhouse is significantly weaker than that of other types under the designed condition, so we choose it as the recommended bucket type. Meanwhile, we compare the rainfall intensity distribution of the original bucket and the recommended bucket under different discharge which rates ranging from 150.71 to 1094.9 m3/s. It is found that the powerhouse and the owner camp are no longer in the heavy rain area under all of the working conditions. Finally, it is shown that the atomization influence during the flood discharge can be reduced by using the recommended bucket.

Sign in / Sign up

Export Citation Format

Share Document