scholarly journals Large eddy simulation of flows in industrial compressors: a path from 2015 to 2035

2014 ◽  
Vol 372 (2022) ◽  
pp. 20130323 ◽  
Author(s):  
N. Gourdain ◽  
F. Sicot ◽  
F. Duchaine ◽  
L. Gicquel
Keyword(s):  
Large Eddy Simulation ◽  
Turbulent Flows ◽  
Complex Geometry ◽  
Current Status ◽  
Navier Stokes ◽  
Future Research ◽  
Phase Lag ◽  
Eddy Simulation ◽  
Large Eddy ◽  
High Reynolds

A better understanding of turbulent unsteady flows is a necessary step towards a breakthrough in the design of modern compressors. Owing to high Reynolds numbers and very complex geometry, the flow that develops in such industrial machines is extremely hard to predict. At this time, the most popular method to simulate these flows is still based on a Reynolds-averaged Navier–Stokes approach. However, there is some evidence that this formalism is not accurate for these components, especially when a description of time-dependent turbulent flows is desired. With the increase in computing power, large eddy simulation (LES) emerges as a promising technique to improve both knowledge of complex physics and reliability of flow solver predictions. The objective of the paper is thus to give an overview of the current status of LES for industrial compressor flows as well as to propose future research axes regarding the use of LES for compressor design. While the use of wall-resolved LES for industrial multistage compressors at realistic Reynolds number should not be ready before 2035, some possibilities exist to reduce the cost of LES, such as wall modelling and the adaptation of the phase-lag condition. This paper also points out the necessity to combine LES to techniques able to tackle complex geometries. Indeed LES alone, i.e. without prior knowledge of such flows for grid construction or the prohibitive yet ideal use of fully homogeneous meshes to predict compressor flows, is quite limited today.

Simulating flow separation from continuous surfaces: routes to overcoming the Reynolds number barrier

2009 ◽  
Vol 367 (1899) ◽  
pp. 2885-2903 ◽  
Author(s):  
Michael Leschziner ◽  
Ning Li ◽  
Fabrizio Tessicini
Keyword(s):  
Reynolds Number ◽  
Turbulent Flows ◽  
Major Elements ◽  
Wall Layer ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rans Models ◽  
High Reynolds ◽  
Near Wall

This paper provides a discussion of several aspects of the construction of approaches that combine statistical (Reynolds-averaged Navier–Stokes, RANS) models with large eddy simulation (LES), with the objective of making LES an economically viable method for predicting complex, high Reynolds number turbulent flows. The first part provides a review of alternative approaches, highlighting their rationale and major elements. Next, two particular methods are introduced in greater detail: one based on coupling near-wall RANS models to the outer LES domain on a single contiguous mesh, and the other involving the application of the RANS and LES procedures on separate zones, the former confined to a thin near-wall layer. Examples for their performance are included for channel flow and, in the case of the zonal strategy, for three separated flows. Finally, a discussion of prospects is given, as viewed from the writer's perspective.

scholarly journals Wall-modeled large-eddy simulation of the flow past a rod-airfoil tandem by the Lattice Boltzmann method

2018 ◽  
Vol 28 (5) ◽  
pp. 1096-1116 ◽  
Author(s):  
Emmanuel Leveque ◽  
Hatem Touil ◽  
Satish Malik ◽  
Denis Ricot ◽  
Alois Sengissen
Keyword(s):  
Large Eddy Simulation ◽  
Turbulent Flows ◽  
Lattice Boltzmann ◽  
Early Stage ◽  
Content Type ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Turbulent Airflow ◽  
High Reynolds ◽  
Boltzmann Method

Purpose The Lattice Boltzmann (LB) method offers an alternative to conventional computational fluid dynamics (CFD) methods. However, its practical use for complex turbulent flows of engineering interest is still at an early stage. This paper aims to outline an LB wall-modeled large-eddy simulation (WMLES) solver. Design/methodology/approach The solver is dedicated to complex high-Reynolds flows in the context of WMLES. It relies on an improved LB scheme and can handle complex geometries on multi-resolution block structured grids. Findings Dynamic and acoustic characteristics of a turbulent airflow past a rod-airfoil tandem are examined to test the capabilities of this solver. Detailed direct comparisons are made with both experimental and numerical reference data. Originality/value This study allows assessing the potential of an LB approach for industrial CFD applications.

Current Status on High Performance Computing for Vehicle Aerodynamics Using Large Eddy Simulation

2007 ◽  
Author(s):  
Makoto Tsubokura ◽  
Takuji Nakashima ◽  
Nobuyuki Oshima ◽  
Kozo Kitoh ◽  
Huilai Zhang ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
High Performance ◽  
Current Status ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
The Earth ◽  
Wind Tunnel Measurement ◽  
Large Eddy ◽  
Vehicle Aerodynamics ◽  
Performance Computing

The world’s largest class unsteady turbulence simulations of flow around vehicles were conducted using Large Eddy Simulation (LES) on the Earth Simulator in Japan. The main objective of our study is to investigate the validity of LES, as an alternative to a conventional wind tunnel measurement or the Reynolds Averaged Navier-Stokes method, for the assessment of vehicle aerodynamics.

Large eddy simulation applications in gas turbines

2009 ◽  
Vol 367 (1899) ◽  
pp. 2827-2838 ◽  
Author(s):  
Kevin Menzies
Keyword(s):  
Large Eddy Simulation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Complex Geometry ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy ◽  
Design Cycle ◽  
Flow Phenomena

The gas turbine presents significant challenges to any computational fluid dynamics techniques. The combination of a wide range of flow phenomena with complex geometry is difficult to model in the context of Reynolds-averaged Navier–Stokes (RANS) solvers. We review the potential for large eddy simulation (LES) in modelling the flow in the different components of the gas turbine during a practical engineering design cycle. We show that while LES has demonstrated considerable promise for reliable prediction of many flows in the engine that are difficult for RANS it is not a panacea and considerable application challenges remain. However, for many flows, especially those dominated by shear layer mixing such as in combustion chambers and exhausts, LES has demonstrated a clear superiority over RANS for moderately complex geometries although at significantly higher cost which will remain an issue in making the calculations relevant within the design cycle.

The emerging role of large eddy simulation in industrial practice: challenges and opportunities

2009 ◽  
Vol 367 (1899) ◽  
pp. 2819-2826 ◽  
Author(s):  
A.G. Hutton
Keyword(s):  
Large Eddy Simulation ◽  
Turbulent Flows ◽  
Best Practice ◽  
Navier Stokes ◽  
Engineering Practice ◽  
Knowledge Based ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Challenges And Opportunities ◽  
History Of

That class of methods for treating turbulence gathered under the banner of large eddy simulation is poised to enter mainstream engineering practice. There is a growing body of evidence that such methods offer a significant stretch in industrial capability over solely Reynolds-averaged Navier–Stokes (RANS)-based modelling. A key enabling development will be the adaptation of innovative processor architectures, resulting from the huge investment in the gaming industry, to engineering analysis. This promises to reduce the computational burden to practicable levels. However, there are many lessons to be learned from the history of the past three decades. These lessons should be analysed in order to inform, if not modulate, the unfolding of this next cycle in the development of industrial modelling capability. This provides the theme for this paper, which is written very much from the standpoint of the informed practitioner rather than the innovator; someone with a strong motivation to improve significantly the competence with which industrial turbulent flows are treated. It is asserted that the reliable deployment of the methodology in the industrial context will prove to be a knowledge-based discipline, as was the case with RANS-based modelling, if not more so. The community at large should collectively make great efforts to put in place that knowledge base from which best practice advice can be derived at the very start of this cycle of advancement and continue to enrich it as the cycle progresses.

Sign in / Sign up

Export Citation Format

Share Document