Improvement of thermal EHL by selecting bush-pin geometry based on an investigation for industrial chains

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Peiran Yang ◽  
Yi Liu ◽  
Zhaohua Shang ◽  
...  
Keyword(s):  
Peer Review ◽  
Elastohydrodynamic Lubrication ◽  
Radius Of Curvature ◽  
Current Standard ◽  
Equivalent Radius ◽  
Content Type ◽  
Finite Line Contact ◽  
Rounded Corner ◽  
Finite Line ◽  
Pin Geometry

Purpose This study aims to investigate the influence of geometry of bush-pin pair from a perspective of optimal lubrication through a thermal elastohydrodynamic lubrication model for finite line contact. Design/methodology/approach A constitutive equation: Ree-Eyring fluid is used in the calculations. The real chain sizes, i.e. equivalent radius of curvature, bush length, length of the rounded corner area and rounded corner radius, are jointed investigated. Moreover, the effects of the length of the rounded corner area and the radius of rounded corner are investigated. Findings It is found that the current standard of the chain might not consider the importance of lubrication, and the lubrication state can be improved effectively by choosing an optimal radius of rounded corner and the length of the corner area. Originality/value By optimally selecting sizes, the occurrence of high pressure, high temperature rise and near zero film thickness at the ends of bush, especially under heavier load, can be effectively avoided. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2020-0031/

A thermal EHL investigation on plate-pin hinge pairs in silent chains using a narrow finite line contact

2020 ◽  
Vol 72 (10) ◽  
pp. 1139-1145
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Jinlei Cui ◽  
Peiran Yang
Keyword(s):  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Radius Of Curvature ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Finite Line Contact ◽  
Pressure Peak ◽  
Finite Line

Purpose The purpose of this paper is to numerically study the variations of oil film pressure, thickness and temperature rise in the contact zone of plate-pin pair in silent chains. Design/methodology/approach A steady-state thermal elastohydrodynamic lubrication (EHL) model is built using a Ree–Eyring fluid. The contact between the plate and the pin is simplified as a narrow finite line contact, and the lubrication state is examined by varying the geometry and the plate speed. Findings With increase in the equivalent radius of curvature, the pressure peak and the central film thickness increase. Because the plate is very thin, the temperature rise can be neglected. Even when the influence of the rounded corner region is less, a proper design can beneficially increase the minimum film thickness at both edges of the plate. Under a low entraining speed, strong stress concentration results in close-zero film thickness at both edges of the plate. Originality/value This study reveals the EHL feature of the narrow finite line contact in plate-pin pairs for silent chains and will support the future works considering transient effect, surface features and wear.

A thermal EHL investigation for size effect of finite line contact on bush-pin hinge pairs in industrial chains

2020 ◽  
Vol 72 (5) ◽  
pp. 695-701
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Peiran Yang ◽  
Zhaohua Shang ◽  
Yi Liu ◽  
...  
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Contact Zone ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Oil Film ◽  
Finite Line Contact ◽  
Finite Line ◽  
Thermal Ehl

Purpose This paper aims to study the influence of the dimension change of bush-pin on the pressure, oil film thickness, temperature rise and traction coefficient in contact zone by using a thermal elastohydrodynamic lubrication (EHL) model for finite line contact. Concretely, the effects of the equivalent curvature radius of the bush and the pin, and the length of the bush are investigated. Design/methodology/approach In this paper, the contact between the bush and pin is simplified as finite line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. A constitutive equation Ree–Eyring fluid is used in the calculations. Findings It is found that by selecting an optimal equivalent radius of curvature and prolonging the bush length can improve the lubrication state effectively. Originality/value Under specific working conditions, there exists an optimal equivalent radius to maximize the minimum oil film thickness in the contact zone. The increase of generatrix length will weaken the stress concentration effect in the rounded corner area at both ends of the bush, which can improve the wear resistance of chain. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2019-0448.

Research on sealing performance of oil seals with micro-dimple texture on lips

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuying Zhang ◽  
Yuanhao Zhang
Keyword(s):  
Peer Review ◽  
Surface Texture ◽  
Elastohydrodynamic Lubrication ◽  
Friction Torque ◽  
Pumping Rate ◽  
Content Type ◽  
Rotation Direction ◽  
Sealing Performance ◽  
Pumping Efficiency ◽  
Shaft Seals

Purpose The purpose of this paper is to study the pumping efficiency of oil seals with different surface textures at different speeds, and the influence of the rotation direction of triangular texture on the sealing performance was further analyzed. Design/methodology/approach Based on the theory of elastohydrodynamic lubrication and the pumping mechanism of rotary shaft seals, establishing a numerical model of mixed lubrication in oil seal sealing area. The model is coupled with the lip surface texture parameters and the two-dimensional average Reynolds equation considering the surface roughness. Findings The results show that the application of lip surface texture technology has obvious influence on the oil film thickness, friction torque and pumping rate of oil seal. The triangular texture has the most significant effect on the increase of pump suction rate. When the rotation direction of triangular texture is 315 degrees, the pumping rate of oil seal is the largest compared with the other seven directions. Originality/value The model has a comprehensive theoretical guidance for the design of new oil seal products, which provides a certain basis for the application of surface texture technology in the field of sealing in the future. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-06-2020-0198/

Surface virtual texturing of the journal bearings of a three-cylinder ethanol engine

2020 ◽  
Vol 72 (9) ◽  
pp. 1059-1073
Author(s):  
Gabriel Welfany Rodrigues ◽  
Marco Lucio Bittencourt
Keyword(s):  
Peer Review ◽  
Power Loss ◽  
Mathematical Formulation ◽  
Surface Texturing ◽  
Elastohydrodynamic Lubrication ◽  
Element Model ◽  
Content Type ◽  
Linear Elastic ◽  
Numerical Experimentation ◽  
Coupling Procedure

Purpose This paper aims to numerically investigate the surface texturing effects on the main bearings of a three-cylinder ethanol engine in terms of the power loss and friction coefficient for dynamic load conditions. Design/methodology/approach The mathematical formulation considers the Partir-Cheng modified Reynolds equation. The mass-conserving Elrod-Adams p-θ model with the JFO approach is used to deal with cavitation. A fluid-structure coupling procedure is considered for the elastohydrodynamic lubrication. Accordingly, a 3-D linear-elastic substructured finite element model obtained from Abaqus is applied Findings Simulations were carried out considering different dimple texture designs in terms of location, depth and radius. The results suggested that there are regions where texturing is more effective. In addition, distinct journal rotation speeds are studied and the surface texture was able to reduce friction and the power loss by 7%. Practical implications The surface texturing can be a useful technique to reduce the power loss on the crankshaft bearing increasing the overall engine efficiency. Originality/value The surface texturing performance in a three-cylinder engine using ethanol as fuel was investigated through numerical experimentation. The results are supported by previous findings. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-09-2019-0380/

scholarly journals A full numerical solution to the coupled cam–roller and roller–pin contact in heavily loaded cam–roller follower mechanisms

2017 ◽  
Vol 232 (10) ◽  
pp. 1273-1284 ◽  
Author(s):  
Shivam S Alakhramsing ◽  
Matthijn B de Rooij ◽  
Dirk J Schipper ◽  
Mark van Drogen
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Friction Model ◽  
Line Contact ◽  
Transient Effects ◽  
Power Losses ◽  
Lubricated Contacts ◽  
Finite Line Contact ◽  
Finite Line ◽  
Lubrication Characteristics ◽  
Lubrication Conditions

In cam–roller follower units two lubricated contacts may be distinguished, namely the cam–roller contact and roller–pin contact. The former is a nonconformal contact while the latter is conformal contact. In an earlier work a detailed transient finite line contact elastohydrodynamic lubrication model for the cam–roller contact was developed. In this work a detailed transient elastohydrodynamic lubrication model for the roller–pin contact is developed and coupled to the earlier developed cam–roller contact elastohydrodynamic lubrication model via a roller friction model. For the transient analysis a heavily loaded cam–roller follower unit is analyzed. It is shown that likewise the cam–roller contact, the roller–pin contact also inhibits typical finite line contact elastohydrodynamic lubrication characteristics at high loads. The importance of including elastic deformation for analyzing lubrication conditions in the roller–pin contact is highlighted here, as it significantly enhances the film thickness and friction coefficient. Other main findings are that for heavily loaded cam–roller follower units, as studied in this work, transient effects and roller slippage are negligible, and the roller–pin contact is associated with the highest power losses. Finally, due to the nontypical elastohydrodynamic lubrication characteristics of both cam–roller and roller–pin contact numerical analysis becomes inevitable for the evaluation of the film thicknesses, power losses, and maximum pressures.

Experimental Investigation for Finite Line Contact Edge Effect of Elastohydrodynamic Lubrication

2012 ◽  
Vol 538-541 ◽  
pp. 1945-1951 ◽  
Author(s):  
Yu Xue ◽  
Tong Shu Hua ◽  
Hao Yang Sun
Keyword(s):  
Experimental Investigation ◽  
Film Thickness ◽  
Contact Area ◽  
Elastohydrodynamic Lubrication ◽  
Line Contact ◽  
Heavy Load ◽  
Entrainment Velocity ◽  
Finite Line Contact ◽  
Finite Line ◽  
Lubricant Viscosity

To reveal the principle of the close effect about the EHL finite roller, contraposing the log-convex roller, the finite line contact EHL film shape and thickness were observed through self-made heavy-load optical EHL experimental device. Experiments were carried out under several different pressure and viscosity, and three groups of interference pictures were obtained under three different entrainment velocities. As the load increased, both the length and width of the roller contact area added, and the width of the contact zone in the end was larger than that in the centre, the close effect was more obvious; when the entrainment velocity and lubricant viscosity increased, the film thickness in the central roller became thicker while the increase in the roller end was little, the high film thickness difference enhanced the close effect. The entrainment velocity, load and lubricant viscosity all have great effect on the EHL characteristics of the finite roller.

Influence of Different Viscosity Lubricant to Finite Line Contacts on Elastohydrodynamic Lubrication (EHL) under Oscillating

2012 ◽  
Vol 538-541 ◽  
pp. 1939-1944
Author(s):  
Yan Fei Wang ◽  
Tong Shu Hua ◽  
Hao Yang Sun
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Oil Film ◽  
Entrainment Velocity ◽  
Finite Line Contact ◽  
Line Contacts ◽  
Finite Line ◽  
Contact Roller ◽  
Two Parameters ◽  
Experimental Rig

To make further researches into the elastohydrodynamic lubrication properties of a finite line contact roller, oscillating experiments were carried out on made overload experimental rig for oil film measurement using optical interference technique. Film thickness and shape were measured in two kinds of viscosity polyisobutylene. This study indicates that both lubricant viscosity and roller entrainment velocity play an important role on EHL of finite line contacts. On motion, the more increase in viscosity or speed, the thicker the oil film thickness, simultaneity edge effect is distinctly intensified and film thickness increases less on roller end, difference of the film thickness is increased between roller end and the central. Above two parameters are significant for logarithmic profile roller in crowning design.

Elastohydrodynamic Lubrication Analysis of Finite Line Contact Problem With Consideration of Two Free End Surfaces

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Haibo Zhang ◽  
Wenzhong Wang ◽  
Shengguang Zhang ◽  
Ziqiang Zhao
Keyword(s):  
Contact Problem ◽  
Finite Length ◽  
Elastohydrodynamic Lubrication ◽  
Line Contact ◽  
Free Boundaries ◽  
Finite Line Contact ◽  
Line Contacts ◽  
Speed Up ◽  
Finite Line ◽  
Overlapping Method

Elastohydrodynamic lubrication (EHL) analysis in finite line contacts is usually modeled by a finite-length roller contacting with a half-space, which ignores effect of the two free boundaries existing in many applications such as gears or roller bearings. This paper presents a semi-analytical method, involving the overlapping method and matrix formation, for EHL analysis in the finite line contact problem to consider the effect of two free end surfaces. Three half-spaces with mirrored loads to be solved are overlapped to cancel out the stresses at expected surfaces, and three matrices can be obtained and reused for the same finite-length space. The isothermal Reynolds equation is solved to obtain the pressure distribution and the fast Fourier transform (FFT) is used to speed up the elastic deformation and stress related calculation. Different line contact situations, including straight rollers, tapered rollers, and Lundberg profile rollers, are discussed to explore the effect of free end surfaces.

Subsurface stress-field analysis of generating ground helical gear based on finite line-contact mixed elastohydrodynamic lubrication

2020 ◽  
Vol 235 (1) ◽  
pp. 3-17
Author(s):  
Zonglin Gu ◽  
Caichao Zhu ◽  
Huaiju Liu ◽  
Jinyuan Tang
Keyword(s):  
Surface Roughness ◽  
Stress Field ◽  
Smooth Surface ◽  
Elastohydrodynamic Lubrication ◽  
Helical Gear ◽  
Tooth Surface ◽  
Finite Line Contact ◽  
Finite Line ◽  
Subsurface Stress ◽  
Maximum Stresses

Tooth surface roughness and lubrication status have significant influence on the contact performance and fatigue life of helical gear pair. Yet, despite the development in elastohydrodynamic lubrication-based contact analysis and solution of subsurface stress field, researches in subsurface stress field of helical gears considering both lubrication and surface roughness are not quite comprehensive. In this study, three-dimensional surface roughness of generating ground gear is measured, a finite line-contact mixed elastohydrodynamic lubrication model is established to perform the contact analysis, and, on this basis, the influence of tooth surface roughness on the subsurface stress field is studied. Results show that compared with the smooth surface, the overall level of subsurface stress is raised; maximum stress values and plastic zones occur in the close vicinity of tooth surface, which adds to the risk of surface failure; within sections in the valley regions of roughness, locations of maximum stresses are generally similar to the smooth surface situation, i.e. in relatively deep zones, while within sections in the peak regions, the majority of locations with maximum stresses shift much closer to the surface; contact pressure and stress status see only mild undulation between different sections distributed along the contact line, but intense changes between sections distributed along the entraining direction.

Sign in / Sign up

Export Citation Format

Share Document