A single layer dual linearly polarized microstrip patch antenna array for automotive applications in the 77 GHz band student submission

2016 ◽  
Author(s):  
Gerhard F. Hamberger ◽  
Stefan Trummer ◽  
Uwe Siart ◽  
Thomas F. Eibert
Keyword(s):  
Antenna Array ◽  
Patch Antenna ◽  
Single Layer ◽  
Microstrip Patch Antenna ◽  
Automotive Applications ◽  
Microstrip Patch ◽  
Linearly Polarized ◽  
77 Ghz

scholarly journals Microwave Wireless Power Transfer System Based on a Frequency Reconfigurable Microstrip Patch Antenna Array

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 415
Author(s):  
Haiyue Wang ◽  
Lianwen Deng ◽  
Heng Luo ◽  
Junsa Du ◽  
Daohan Zhou ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Antenna Array ◽  
Patch Antenna ◽  
Wireless Power Transfer ◽  
Microstrip Patch Antenna ◽  
Market Demand ◽  
Power Transfer ◽  
Wireless Power ◽  
Microstrip Patch ◽  
Wide Range

The microwave wireless power transfer (MWPT) technology has found a variety of applications in consumer electronics, medical implants and sensor networks. Here, instead of a magnetic resonant coupling wireless power transfer (MRCWPT) system, a novel MWPT system based on a frequency reconfigurable (covering the S-band and C-band) microstrip patch antenna array is proposed for the first time. By switching the bias voltage-dependent capacitance value of the varactor diode between the larger main microstrip patch and the smaller side microstrip patch, the working frequency band of the MWPT system can be switched between the S-band and the C-band. Specifically, the operated frequencies of the antenna array vary continuously within a wide range from 3.41 to 3.96 GHz and 5.7 to 6.3 GHz. For the adjustable range of frequencies, the return loss of the antenna array is less than −15 dB at the resonant frequency. The gain of the frequency reconfigurable antenna array is above 6 dBi at different working frequencies. Simulation results verified by experimental results have shown that power transfer efficiency (PTE) of the MWPT system stays above 20% at different frequencies. Also, when the antenna array works at the resonant frequency of 3.64 GHz, the PTE of the MWPT system is 25%, 20.5%, and 10.3% at the distances of 20 mm, 40 mm, and 80 mm, respectively. The MWPT system can be used to power the receiver at different frequencies, which has great application prospects and market demand opportunities.

scholarly journals Single-Layer Line-Fed Broadband Microstrip Patch Antenna on Thin Substrates

Electronics ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 37
Author(s):  
Roberto Vincenti Gatti ◽  
Riccardo Rossi ◽  
Marco Dionigi
Keyword(s):  
Patch Antenna ◽  
State Of The Art ◽  
Low Cost ◽  
Single Layer ◽  
Microstrip Antennas ◽  
Microstrip Patch Antenna ◽  
Layer Line ◽  
Limited Bandwidth ◽  
Microstrip Patch ◽  
Effective Design

In this work, the issue of limited bandwidth typical of microstrip antennas realized on a single thin substrate is addressed. A simple yet effective design approach is proposed based on the combination of traditional single-resonance patch geometries. Two novel shaped microstrip patch antenna elements with an inset feed are presented. Despite being printed on a single-layer substrate with reduced thickness, both radiators are characterized by a broadband behavior. The antennas are prototyped with a low-cost and fast manufacturing process, and measured results validate the simulations. State-of-the-art performance is obtained when compared to the existing literature, with measured fractional bandwidths of 3.71% and 6.12% around 10 GHz on a 0.508-mm-thick Teflon-based substrate. The small feeding line width could be an appealing feature whenever such radiating elements are to be used in array configurations.

scholarly journals 2.45 GHz wearable rectenna array design for microwave energy harvesting

2019 ◽  
Vol 14 (2) ◽  
pp. 677 ◽  
Author(s):  
Syahirah Shawalil ◽  
Khairul Najmy Abdul Rani ◽  
Hasliza A. Rahim
Keyword(s):  
Antenna Array ◽  
Patch Antenna ◽  
Wireless Body Area Network ◽  
Microstrip Patch Antenna ◽  
Circuit Board ◽  
Design System ◽  
Area Network ◽  
Dc Voltage ◽  
Rectifier Circuit ◽  
Microstrip Patch

This paper presents a design of a wearable textile microstrip patch rectifying antenna (rectenna) array operating for wireless body area network (WBAN) at the center frequency, <em>f<sub>c</sub></em> of 2.45 GHz.  Precisely, jeans or denim with the relative permittivity, <sub> </sub>= 1.70 and thickness of 1.00 mm is chosen as a substrate attached to SheildIt Super as a conductive material with the thickness, <em>h</em> of 0.17 mm and conductivity of 6.67  10<sup>5</sup> S/m, respectively. In the first stage, a microstrip patch antenna array layout with the inset fed technique is designed and simulated by using the Keysight Advanced Design System (ADS) software.  In the second stage, a wearable textile microstrip patch antenna array is fabricated, integrated, and hidden inside the jeans fabric.  In the third stage, the rectifier circuit layout on the flame retardant-4    (FR-4) printed circuit board (PCB) with the dielectric constant,  = 4.7, thickness, <em>h</em> = 1.6 mm, and loss tangent, <em>δ</em> = 0.018 that can generate radio frequency-direct current (RF-DC) conversion is designed and simulated using the ADS software  Each simulation result and fabrication measurement shows that the designed antenna array characteristics are suitable for an industrial, scientific, and medical radio (ISM) band by having the reflection coefficient, <em>S</em><sub>11</sub> less than -10 decibel (dB) at the respective resonant frequency, <em>f<sub>r</sub>.</em>  Moreover, through simulation, the output DC voltage for the bridge rectifier circuit is from 132 mV to 5.01 V with the corresponding power conversion efficiency (PCE) between 3.48% and 50.20% whereas for the voltage doubler rectifier, the output DC voltage is from 417 mV to 2.91 V with the corresponding PCE between 34.78% and 53.56%, respectively.

Sign in / Sign up

Export Citation Format

Share Document