A dynamic measurement method for parasitic capacitances of high voltage SiC MOSFETs

2015 ◽  
Author(s):  
Xiaoqing Song ◽  
Alex Q. Huang ◽  
Mengjia Lee ◽  
Gangyao Wang
Keyword(s):  
High Voltage ◽  
Measurement Method ◽  
Dynamic Measurement

A Drain–Source Connection Technique: Thermal Resistance Measurement Method for GaN HEMTs Using TSEP at High Voltage

2020 ◽  
Vol 67 (12) ◽  
pp. 5454-5459
Author(s):  
Xuan Li ◽  
Shiwei Feng ◽  
Chang Liu ◽  
Yamin Zhang ◽  
Kun Bai ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
High Voltage ◽  
Measurement Method ◽  
Resistance Measurement ◽  
Gan Hemts

Research on Damage Status of the Reinforced Concrete Ground Floor Columns

2012 ◽  
Vol 226-228 ◽  
pp. 1436-1440
Author(s):  
Li Jun Gao ◽  
Yong Sheng Zhang ◽  
Qin Li
Keyword(s):  
Reinforced Concrete ◽  
Measurement Method ◽  
Damping Ratio ◽  
Simple Calculation ◽  
Dynamic Measurement ◽  
Concrete Column ◽  
Destructive Testing ◽  
Reinforced Concrete Column ◽  
First Order ◽  
Vibration Model

In this paper, dynamic measurement method is applied to test the damage of the bottom reinforced concrete column. The comparison between the calculated first order frequency of the bottom reinforced concrete column and the measured first order frequency shows that the result is consistent. This indicates that this approach is feasible. However, in recent years, dynamic measurement method is widely used in non-destructive testing of bridges and floors. The principle of the dynamic measurement method for the detection of reinforced concrete column utilizes the measured natural frequency, vibration model and damping ratio of reinforced concrete column and such inherent dynamic characteristics of indicators to reflect the damage of reinforced concrete column. And there is no secondary injury for the column. The simplified method of structure dynamics is applied to calculate the frequency of the bottom reinforced concrete column. And the simple calculation method is verified by experiment and practice.

The robustness verification of the D-VHS trick play using dynamic measurement method for evaluating mechanism

2000 ◽  
Vol 46 (3) ◽  
pp. 481-486
Author(s):  
M. Matsumaru ◽  
T. Ohishi ◽  
T. Eino ◽  
Y. Togo ◽  
M. Tsuruta
Keyword(s):  
Measurement Method ◽  
Dynamic Measurement

Study on 3-D Measurement Method in Shake Table Tests Using Image Processing Technique: 1st Report - Verification of Synthetic Performance of the Measurement System

2004 ◽  
Author(s):  
Satoshi Fujita ◽  
Osamu Furuya ◽  
Yasushi Niitsu
Keyword(s):  
Measurement System ◽  
Measurement Method ◽  
Measurement Accuracy ◽  
Dynamic Measurement ◽  
Processing Technique ◽  
Shake Table Test ◽  
Image Processing Technique ◽  
Shake Table ◽  
Shake Table Tests ◽  
3 Dimensional

This study has been doing research and development of 3-dimensional measurement method using the image processing technique for the measurement of dynamic displacement in shake table test. This measurement system is a very convenient system because it can measure the three-dimensional dynamic displacement in shake table test in which the several makers are only attached to the surface of an experimental structure. The system therefore is the most suitable measurement system for an evaluation of complex 3-dimensional behavior of experimental model. Fundamental hardware and software for the measurement system have been constructed until now. The fundamental dynamic measurement accuracy and effectiveness of the measurement system have been also confirmed from several shake table tests. This paper describes the dynamic measurement accuracy in shake table test in with the experimental model has several rotational behaviors, and also summarizes the synthetic performance of the proposed measurement system.

Sign in / Sign up

Export Citation Format

Share Document