scholarly journals Comparison of major biological and technical complications between hybrid resin and zirconia FTI‐FDPs

2020 ◽  
Vol 31 (S20) ◽  
pp. 220-220
Author(s):  
Yukari Oda ◽  
Gentaro Mori ◽  
Toshikazu Iijima ◽  
Yasutomo Yajima
2021 ◽  
Vol 9 (1) ◽  
pp. 8
Author(s):  
Murtadha AlAli ◽  
Nikolaos Silikas ◽  
Julian Satterthwaite

Objective: To evaluate and compare the surface roughness and gloss of a DMA-free composite and Bis-GMA-free composite with a DMA-based composite before and after toothbrushing simulation. Materials and Methods: Fifteen dimensionally standardised composite specimens of three nano-hybrid resin composites (Tetric EvoCeram, Admira Fusion, and Venus Diamond) were used. Five specimens from each composite were polished and then subjected to a toothbrushing simulator. Surface roughness (Ra) and gloss were measured before toothbrushing and after 5000, 10,000, 15,000, and 20,000 toothbrushing cycles. The data was analysed using 5 × 3 ANOVA to assess surface roughness and gloss values and pairwise comparisons in the form of Tukey post hoc tests were performed to interpret main effects. Results: For all tested materials, surface roughness increased, and gloss decreased after toothbrushing abrasion. Surface roughness (Ra) values ranged from 0.14 to 0.22 μm at baseline and increased to between 0.41 and 0.49 μm after 20,000 toothbrushing cycles. Gloss values ranged between 31.9 and 50.6 GU at baseline and between 5.1 and 19.5 GU after 20,000 toothbrushing cycles. The lowest initial Ra value was detected in Venus Diamond and the highest initial gloss value was detected in Tetric EvoCeram. Conclusions: Simulated toothbrushing abrasion led to an increase in surface roughness and a decrease in gloss for all tested materials. Venus Diamond had the smoothest surface and Tetric EvoCeram had the glossiest surface after polishing and following 20,000 cycles of toothbrushing abrasion. Admira Fusion demonstrated the roughest surface and had the lowest gloss values before and after toothbrushing abrasion.


2014 ◽  
Vol 27 (6) ◽  
pp. 544-552 ◽  
Author(s):  
Lumni Kolgeci ◽  
Erno Mericske ◽  
Andreas Worni ◽  
Petra Walker ◽  
Joannis Katsoulis ◽  
...  

2019 ◽  
Vol 4 (3) ◽  
pp. 647-651 ◽  
Author(s):  
Darius Gailevičius ◽  
Viktorija Padolskytė ◽  
Lina Mikoliūnaitė ◽  
Simas Šakirzanovas ◽  
Saulius Juodkazis ◽  
...  

An approach enabling nanoscale-additive manufacturing of inorganics based on phase transition via calcination of laser structured hybrid resin is proposed.


2006 ◽  
Vol 72 (11) ◽  
pp. 1070-1081
Author(s):  
Michael A. Goldfarb ◽  
Thomas Baker

In this article, a reproducible process for presenting, analyzing, and reducing early and late surgical morbidity and mortality (M&M) is detailed. All M&M cases presented from 1998 through 2005 at Monmouth Medical Center were categorized. Residents and nurses were empowered to report the complications. The five major categories were overwhelming disease on admission, delays in treatment, diagnostic or judgment complications, treatment complications, and technical complications. From the 53,541 operations performed over 8 years, 714 patients were presented, which included 147 deaths and 1,132 category entries. The most common problems were technical complications in 474 (66.4%) patients. The data have generated actionable solutions, many with low barriers to adoption, resulting in safer, less expensive surgical management. Surgical outcome benchmarks have been established and are used for credentialing surgeons. The “Hostile Abdomen Index” has been developed to assess the safest choice for abdominal operative access, pre- and intraoperatively. We explained the real-time process that generated solutions for the entire department as well as changes relevant to residency training and individual operative techniques.


2020 ◽  
Vol 57 (1) ◽  
pp. 133-140
Author(s):  
Dumitru Bolcu ◽  
Marius Marinel Stanescu ◽  
Ion Ciuca ◽  
Cosmin Mihai Miritoiu ◽  
Alin Dinita ◽  
...  

This paper studies the influence of the volume proportion between components on the mechanical behaviour of a hybrid resin obtained by combining the natural resin Dammar and epoxy resin. We analyse three sets of hybrid resin samples, in which we used a Dammar volume proportion of 60%, 70%, and 80% respectively and epoxy resin (employed together with its associated reinforcement in order to generate a quick process of polymerization). Following the tensile test we found the characteristic curves, the tensile strength and the elongation at break for each of the three types of resins. We also looked into the vibration damping properties of bars made of this resin. We experimentally determined the frequency and the damping coefficient of the first particular vibration mode for one bar taken out of each set of resins, with one end fixed and the other free. On the basis of the results, we calculated the loss coefficient for each type of resin.


2014 ◽  
Vol 77 (1) ◽  
pp. 24-29 ◽  
Author(s):  
Shinji Kanehashi ◽  
Hiroki Oyagi ◽  
Rong Lu ◽  
Tetsuo Miyakoshi
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document