Jet Interaction in Liquid-Liquid Coaxial Injectors

1996 ◽  
Vol 118 (2) ◽  
pp. 329-334 ◽  
Author(s):  
D. Sivakumar ◽  
B. N. Raghunandan
Keyword(s):  
Pressure Drop ◽  
Strong Influence ◽  
Cone Angle ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Jet Interaction ◽  
Liquid Sheets ◽  
The Core ◽  
Swirl Injector ◽  
Separation Behavior

Interaction between two conical sheets of liquid formed by a coaxial swirl injector has been studied using water in the annular orifice and potassium permanganate solution in the inner orifice. Experiments using photographic techniques have been conducted to study the influence of the inner jet on outer conical sheet spray characteristics such as spray cone angle and break-up length. The core spray has a strong influence on the outer sheet when the pressure drop in the latter is low. This is attributed to the pressure variations caused by ejector effects. This paper also discusses the merging and separation behavior of the liquid sheets which exhibits hysteresis effect while injector pressure drop is varied.

Effect of geometric and operating parameters on the spray characteristics of an open-end swirl injector

2019 ◽  
Vol 233 (12) ◽  
pp. 4457-4467 ◽  
Author(s):  
Chen Chen ◽  
Yang Yang ◽  
Xiaorong Wang ◽  
Wenxian Tang
Keyword(s):  
Pressure Drop ◽  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Operating Parameters ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Swirl Chamber ◽  
Swirl Injector

To study the influence of geometric and operating parameters on the spray characteristics of an open-end swirl injector, seven injectors with different tangential inlet diameters ( D p) and injector length to injector orifice diameter ( L/D) ratios were tested and simulated. Using high-speed backlight, the evolution laws of liquid film thickness, discharge coefficient, spray cone angle, breakup length, and velocity distribution in the swirl chamber under different geometric and operating parameters were captured after unified image processing. Low-injection pressure drop is directly proportional to the discharge coefficient and the spray cone angle. When the injection pressure drop approaches or reaches a critical value of 0.4 MPa, the discharge coefficient and spray cone angle remain nearly constant with maximum fluctuations of 1% and 5%, respectively. With an increase in the geometric characteristic constant A, the liquid film thickness, discharge coefficient, breakup length, and velocity in the swirl chamber decrease, whereas the spray cone angle increases. As the viscous effect increases for increasing L/D, the discharge coefficient and breakup length increase, whereas the spray cone angle decreases. Based on experiment results, empirical formulas for the discharge coefficient, spray angle, and breakup length were put forward as reference for engineering applications, including the effect of the geometric and operating parameters.

The Application of Cyclone Theories to Centrifugal Spray Nozzles

1947 ◽  
Vol 157 (1) ◽  
pp. 111-119 ◽  
Author(s):  
S. M. Doble ◽  
E. M. Halton
Keyword(s):  
Pressure Drop ◽  
Film Thickness ◽  
Cone Angle ◽  
Theoretical Explanation ◽  
Spray Characteristics ◽  
Empirical Relationships ◽  
Spray Cone Angle ◽  
Design Data ◽  
Spray Cone ◽  
Nozzle Shape

The problem of designing centrifugal spray nozzles has been attacked by applying well-established cyclone formulae; these provide a theoretical explanation for empirical relationships (which have been obtained previously‡) between nozzle output, spray cone angle, and pressure drop. The nozzle is designed by first selecting suitable values of the following quantities:— [Formula: see text] Both the above quantities should be greater than 1 in order that the subsequent prediction of design data may be as accurate as possible. Apart from this limitation, the values assigned to those quantities are largely arbitrary in that they are not dependent upon the final spray characteristics required, but, as they affect the dimensions of the nozzle, the original selection may have to be adjusted after preliminary calculations if the estimated nozzle shape is in any way unsuitable. They may also have to be adjusted if they result in the calculated value of the quantity t/RE, i.e. (orifice film thickness)/(exit radius), being much greater than 00·5, as this will involve loss of accuracy in applying the theoretical equations. Having finally selected suitable values of Φ and Ri/ Re, the dimensions of the nozzle can be calculated by substituting the required values of the spray characteristics in the various formulae.

Method of Identifying Injector Coking From the Spray Field of Mechanical and CRDi Injectors Using Intensity of Scattered Light

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Ronith Stanly ◽  
Gopakumar Parameswaran ◽  
Bibin Sagaram
Keyword(s):  
Scattered Light ◽  
Near Field ◽  
Cone Angle ◽  
Angle Measurement ◽  
Field Region ◽  
Fuel System ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Cleaning Procedure ◽  
Spray Field

The influence of injector coking deposits on the spray field of single-hole mechanical port fuel injectors and multihole common rail direct injection (CRDi) injectors was studied using light scattering technique coupled with image processing and analysis. Instead of employing the traditional accelerated coking process to study injector spray field deterioration, in-service injectors were selected and cleaned using a commercial fuel system cleaning procedure. Variation in atomization characteristics of coked and cleaned injectors were observed based on the spatial distribution of fine, medium, and coarse droplets in the near-field region of the injector spray zone and analyzed as a function of the intensity of scattered light. The improvement in the atomization perceived by this method was compared with traditional techniques like spray cone angle measurement, speed characterization of spray jets, and weight reduction of injector nozzles and needles. It was observed that after the fuel system cleaning procedure, a reduction in the number of coarse droplets in the near-field region and an increase in the number of medium and finely sized droplets was observed, suggesting better atomization of fuel in the near field spray zone.

Experimental and Numerical Studies of Diesel Spray Evaporation and Combustion in a Gas Turbine Matrix Burner

2009 ◽  
Author(s):  
Dieter Bohn ◽  
James F. Willie ◽  
Nils Ohlendorf
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Combustion Instability ◽  
Cone Angle ◽  
Spray Angle ◽  
Test Rig ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Flow Simulations ◽  
Air Inlet

Lean gas turbine combustion instability and control is currently a subject of interest for many researchers. The motivation for running gas turbines lean is to reduce NOx emissions. For this reason gas turbine combustors are being design using the Lean Premixed Prevaporized (LPP) concept. In this concept, the liquid fuel must first be atomized, vaporized and thoroughly premixed with the oxidizer before it enters the combustion chamber. One problem that is associated with running gas turbines lean and premixed is that they are prone to combustion instability. The matrix burner test rig at the Institute of Steam and Gas Turbines at the RWTH Aachen University is no exception. This matrix burner is suitable for simulating the conditions prevailing in stationary gas turbines. Till now this burner could handle only gaseous fuel injection. It is important for gas turbines in operation to be able to handle both gaseous and liquid fuels though. This paper reports the modification of this test rig in order for it to be able to handle both gaseous and liquid primary fuels. Many design issues like the number and position of injectors, the spray angle, nozzle type, droplet size distribution, etc. were considered. Starting with the determination of the spray cone angle from measurements, CFD was used in the initial design to determine the optimum position and number of injectors from cold flow simulations. This was followed by hot flow simulations to determine the dynamic behavior of the flame first without any forcing at the air inlet and with forcing at the air inlet. The effect of the forcing on the atomization is determined and discussed.

Effects of Fuel Nozzle Condition on Gas Turbine Combustion Chamber Exit Temperature Distributions

2010 ◽  
Author(s):  
Kristen Bishop ◽  
William Allan
Keyword(s):  
Combustion Chamber ◽  
Ambient Pressure ◽  
Cone Angle ◽  
Operating Conditions ◽  
Spray Cone Angle ◽  
Mixing Processes ◽  
Spray Cone ◽  
Temperature Distributions ◽  
Fuel Nozzle ◽  
Exit Temperature

The effects of fuel nozzle condition on the temperature distributions experienced by the nozzle guide vanes have been investigated using an optical patternator. Average spray cone angle, symmetry, and fuel streaks were quantified. An ambient pressure and temperature combustion chamber test rig was used to capture exit temperature distributions and to determine the pattern factor. The rig tests matched representative engine operating conditions by matching Mach number, equivalence ratio, and fuel droplet size. It was observed that very small deviations (± 10° in spray cone angle) from a nominal distribution in the fuel nozzle spray pattern correlated to increases in pattern factor, apparently due to a degradation of mixing processes, which created larger regions of very high temperature core flow and smaller regions of cooler temperatures within the combustion chamber exit plane. The spray cone angle had the most measureable influence while the effects of spray roundness and streak intensity had slightly less influence. Comparisons were made with published studies conducted on the combustion chamber geometry, and recommendations were made for fuel nozzle inspections.

scholarly journals Experimental Study of Spray Characteristics of Kerosene-Ethanol Blends from a Pressure-Swirl Nozzle

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Tao Zhang ◽  
Bo Dong ◽  
Xun Zhou ◽  
Linan Guan ◽  
Weizhong Li ◽  
...  
Keyword(s):  
Discharge Coefficient ◽  
Cone Angle ◽  
Injection Pressure ◽  
Spray Characteristics ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Breakup Length ◽  
Ethanol Blends ◽  
Pressure Swirl ◽  
Spray Velocity

Partial replacement of kerosene by ethanol in a gas turbine is regarded as a good way to improve the spray quality and reduce the fossil energy consumption. The present work is aimed at studying the spray characteristics of kerosene-ethanol blends discharging from a pressure-swirl nozzle. The spray cone angle, discharge coefficient, breakup length, and velocity distribution are obtained by particle image velocimetry, while droplet size is acquired by particle/droplet imaging analysis. Kerosene, E10 (10% ethanol, 90% kerosene), E20 (20% ethanol, 80% kerosene), and E30 (30% ethanol, 70% kerosene) have been considered under the injection pressure of 0.1–1 MPa. The results show that as injection pressure is increased, the discharge coefficient and breakup length decrease, while the spray cone angle, drop size, and spray velocity increase. Meanwhile, the drop size decreases and the spray velocity increases with ethanol concentration when the injection pressure is lower than 0.8 MPa. However, the spray characteristics are not affected obviously by the ethanol concentration when the injection pressure exceeds 0.8 MPa. A relation to breakup length for kerosene-ethanol blends is obtained. The findings demonstrate that the adding of ethanol into kerosene can promote atomization performance.

Sign in / Sign up

Export Citation Format

Share Document