Average Physical Parameters in an Air-Water Two-Phase Flow in a Small, Square-Sectioned Channel

1994 ◽  
Vol 116 (2) ◽  
pp. 247-254 ◽  
Author(s):  
J. K. Keska ◽  
R. D. Fernando
Keyword(s):  
Experimental Data ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Full Range ◽  
Flow Patterns ◽  
Physical Parameters ◽  
Phase Flow ◽  
Spatial Concentration ◽  
Two Phase ◽  
Concentration Measurements

This experimental study focuses on an adiabatic two-phase air-water flow generated in a small, horizontal, 6.35 mm square channel. Pressure and temperature were near standard conditions. Experimental data and correlations available in the literature, generally, do not consider the full range of concentration, small cross-sectional areas and direct physical parameters, such as concentration (void fraction) and/or phase velocities. Based on the direct measurement of in-situ spatial concentration (in a full range of concentrations, including gas and liquid phases only), and flow-pattern determination, the experimental data from the study are compared with data from the literature and with prediction by the generally accepted Lockhart-Martinelli’s and Chen’s models. Spatial concentration measurements were made with a computer-based system developed and built by the authors. Pressure drop over a length of the channel was also measured with pressure transducers. These measurements were made for a variety of flow conditions which encompassed bubble, slug, plug, and annular flow regimes. Flow patterns were established, and both mean and fluctuating components of the concentration measurements were used to objectively identify the flow patterns. These results, together with visual enhanced observation (stroboscope) supplemented with a high-speed CCD camera recording enhanced with dye injection, were used to obtain flow-pattern maps and compared with the literature. Spatial concentration is shown to be a key physical parameter in describing the state of the mixture in two-phase flow.

Model of Two-Phase Heterogeneous Mixture Flow in a Microchannel With Incorporated Flow Patterns

2005 ◽  
Author(s):  
Jerry K. Keska
Keyword(s):  
Mathematical Model ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Full Range ◽  
Flow Patterns ◽  
Calculation Model ◽  
Phase Flow ◽  
Heterogeneous Mixture ◽  
Two Phase ◽  
Mixture Flow

In the two-phase or multiphase flow of such heterogeneous mixture like gas-liquid there is a very complicated and random phenomenon of flow patterns, which needs to be quantitatively and accurately, incorporated. Unfortunately, a model with quantitatively incorporated flow patterns in full range of concentration or method of how to measure flow patterns is not available. Recognizing these challenges this paper will present an approach to incorporate flow pattern phenomenon into the two-phase flow calculation model by (1) developing a mathematical model for pressure losses in two-phase flow based on in-situ parameters, (2) developing and defining a flow pattern coefficient, which incorporates the flow pattern phenomena, and (3) present the developed mathematical model with the incorporation of flow patterns, which demonstrated significant increase of accuracy of calculations based on conducted experimental research on air-water two-phase mixture flow in a horizontal square microchannel.

Incorporated Flow Patterns Into a Model of Two-Phase Heterogeneous Mixture Flow in Microchannels

2006 ◽  
Author(s):  
Jerry K. Keska
Keyword(s):  
Mathematical Model ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Full Range ◽  
Flow Patterns ◽  
Phase Flow ◽  
Heterogeneous Mixture ◽  
Two Phase ◽  
Mixture Flow ◽  
Pressure Losses

In the two-phase or multiphase flow of such heterogeneous mixture like gas-liquid many more independent parameters are involved, thereby making this process more complicated and less transparent for understanding, mathematical modeling and simulating or calculating of such parameter like the length pressure gradient. In two-phase flow, there is a very complicated and random phenomenon of flow patterns, which needs to be quantitatively and accurately incorporated. Unfortunately, nowadays, a method of how to measure flow patterns is not available. And, also there is a need for mathematical models with quantitatively incorporated flow patterns in full range of flow. It is understandable that in all such cases any reasonable attempt to define and incorporate quantitatively this phenomenon in mathematical model will be beneficial. Recognizing these challenges this paper will present an approach to incorporate flow pattern phenomenon into the two-phase flow model by (1) developing a mathematical model for pressure losses in two-phase flow based on in-situ parameters, (2) developing and defining a flow pattern coefficient, which incorporates the flow pattern phenomena, and (3) present the developed mathematical model with the incorporation of flow patterns, which demonstrated significant increase of accuracy of calculations based on conducted experimental research on air-water twophase mixture flow in a horizontal square microchannel.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2003 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase ◽  
Micro Channels

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.

Detecting the Flow Pattern Transition in the Gas-Liquid Two-Phase Flow Using Multivariate Multi-Scale Entropy Analysis

2019 ◽  
Vol 74 (10) ◽  
pp. 837-848 ◽  
Author(s):  
Yudong Liu ◽  
Dayang Wang ◽  
Yingyu Ren ◽  
Ningde Jin
Keyword(s):  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Mean Value ◽  
Entropy Rate ◽  
Permutation Entropy ◽  
Phase Flow ◽  
Two Phase ◽  
Multi Scale ◽  
Flow Pattern Transition

AbstractDue to the complex flow structure and non-uniform phase distribution in the vertical upward gas-liquid two-phase flow, an eight-electrode rotating electric field conductance sensor is used to obtain multi-channel conductance signals. The flow patterns of the vertical upward gas-liquid two-phase flow are classified according to the images obtained from a high-speed camera. Then, we employ the multivariate weighted multi-scale permutation entropy (MWMPE) to detect the instability of flow pattern transition in the gas-liquid two-phase flow. Afterwards, we compare the results of the MWMPE with those of the single-channel weighted multi-scale permutation entropy (SCWMPE) and multivariate multi-scale sample entropy (MMSE). The comparison results indicate that, compared with the SCWMPE and MMSE, the MWMPE has superior performance in terms of the high-resolution presentation of flow instability in the gas-liquid two-phase flow. Finally, we extract the mean value of the MWMPE in whole scales and the entropy rate of the MWMPE in the small scales. The results indicate that the normalized mean value and normalized entropy rate of MWMPE are very sensitive to the transitions of flow patterns, thus allowing the detection of the instability of flow pattern transition.

Flow Boiling Visualization of R-134a in a Vertical Channel of Small Diameter

2007 ◽  
Author(s):  
Claudi Marti´n-Callizo ◽  
Bjo¨rn Palm ◽  
Wahib Owhaib ◽  
Rashid Ali
Keyword(s):  
Flow Pattern ◽  
Annular Flow ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Bubbly Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
R 134A ◽  
Heated Length

The present work reports on flow boiling visualization of refrigerant R-134a in a vertical circular channel with internal diameter of 1.33 mm and 235 mm in heated length. Quartz tube with a homogeneous ITO-coating is used allowing heating and simultaneous visualization. Flow patterns have been observed along the heated length with the aid of a digital camera with close-up lenses. From the flow boiling visualization, seven distinct two-phase flow patterns have been observed: Isolated bubbly flow, confined bubbly flow, slug flow, churn flow, slug-annular flow, annular flow, and mist flow. Two-phase flow pattern observations are presented in the form of flow pattern maps. Finally, the experimental flow pattern map is compared to models developed for conventional sizes as well as to a microscale map for air-water mixtures available in the literature, showing a large discrepancy.

Experimental Investigation on Flow Patterns and Frictional Pressure Drop of Downward Air-Water Two-Phase Flow in Vertical Pipes

2013 ◽  
Author(s):  
Yuqing Xue ◽  
Huixiong Li ◽  
Tianyou Sheng ◽  
Changjiang Liao
Keyword(s):  
Pressure Drop ◽  
Flow Pattern ◽  
Oil Recovery ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Vertical Pipe ◽  
Two Phase Flows ◽  
Two Phase ◽  
Frictional Pressure Drop

A large amount of air need be transported into the reservoir in the deep stratum to supply oxygen to some microbes in Microbial Enhanced Oil Recovery (MEOR). Air-water two-phase flows downward along vertical pipeline during the air transportation. Base on the experiment data described in this paper, the characteristics of air-water two phase flow patterns were investigated. The flow pattern map of air-water two phase flows in the pipe with inner diameter of 65 mm was drawn, criterions of flow pattern transition were discussed, and the dynamic signals of the pressure and the differential pressure of the two phase flow were recorded to characterize the three basic flow regimes indirectly. The frictional pressure drop of downward flow in vertical pipe must not be disregarded contrast with upward two phase flow in the vertical pipe because the buoyancy must be overcame when the gas flows downward along pipe, and there would be a maximum value of frictional when the flow pattern translated from slug flow to churn flow.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2004 ◽  
Vol 126 (3) ◽  
pp. 288-300 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406×2.032mm2 cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Features unique to two-phase micro-channel flow were identified and employed to validate key assumptions of an annular flow boiling model that was previously developed to predict pressure drop and heat transfer in two-phase micro-channel heat sinks. This earlier model was modified based on new findings from the adiabatic two-phase flow study. The modified model shows good agreement with experimental data for water-cooled heat sinks.

An Experimental Study on Air-Water Two-Phase Flow Patterns in Pebble Beds

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Bai Bofeng ◽  
Liu Maolong ◽  
Su Wang ◽  
Zhang Xiaojie
Keyword(s):  
Experimental Study ◽  
Flow Pattern ◽  
Test Section ◽  
Slug Flow ◽  
Annular Flow ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Pattern Transition

An experimental study was conducted on the air-water two-phase flow patterns in the bed of rectangular cross sections containing spheres of regular distribution. Three kinds of glass spheres with different diameters (3 mm, 6 mm, and 8 mm) were used for the establishment of the test section. By means of visual observations of the two-phase flow through the test section, it was discovered that five different flow patterns occurred within the experimental parameter ranges, namely, bubbly flow, bubbly-slug flow, slug flow, slug-annular flow, and annular flow. A correlation for the bubble and slug diameter in the packed beds was proposed, which was an extended expression of the Tung/Dhir model, Jamialahmadi’s model, and Schmidt’s model. Three correlations were proposed to calculate the void friction of the flow pattern transition in bubble flow, slug flow, and annular flow based on the bubble model in the pore region. The experimental result showed that the modified Tung and Dhir model of the flow pattern transition was in better agreement with the experimental data compared with Tung and Dhir’s model.

Flow Characteristics and Frictional Pressure Drops of Gas-Liquid Two-Phase Flow in Mini-Micro Pipes and at Vena Contract and Expansion

2007 ◽  
Author(s):  
Hiroyasu Ohtake ◽  
Hideyasu Ohtaki ◽  
Yasuo Koizumi
Keyword(s):  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Liquid Velocity ◽  
Flow Patterns ◽  
Experimental Results ◽  
Phase Flow ◽  
Two Phase ◽  
Pressure Drops ◽  
Frictional Pressure Drop

The frictional pressure drops and two-phase flow patterns of gas-liquid two-phase flow in mini-micro pipes and at vena contract and expansion were investigated experimentally. Test liquid was water; test gas was argon. The diameter of the test mini-pipe was 0.5, 0.25 and 0.12 mm, respectively. The pressure drop data and the flow pattern were collected over 2.1 < Ug < 92.5 m/s for the superficial gas velocity and 0.03 < Ul < 10 m/s for the superficial liquid velocity. The experimental results show that the flow patterns were slug, churn, ring and annular flows; pure bubbly flow pattern was not observed in a range of the present experimental conditions. The two-phase friction multiplier data for D > 0.5 mm showed to be in good agreement with the conventional correlations. On the other hand, the two-phase friction multiplier data for D < 0.25 mm differed from the calculated values by the conventional correlations. Then, thickness of liquid film around a gas plug and size of gas core were estimated and the effect of frictional pressure drop on channel size was discussed through Knudsen Number of gas and instability on liquid-gas interface. The coefficients of sudden enlargement and sudden contraction in mini-pipes for the gas-water two-phase flow were modified from the present experimental results.

Two-Phase Flow Patterns During Microchannel Vaporization of CO2 at Near-Critical Pressures

2003 ◽  
Author(s):  
Jostein Pettersen
Keyword(s):  
Heat Transfer ◽  
Flow Pattern ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Bubble Formation ◽  
Glass Tube ◽  
Flow Patterns ◽  
High Mass ◽  
Phase Flow ◽  
Two Phase

Carbon dioxide (CO2 / R-744) is receiving renewed interest as a refrigerant, in many cases based on systems with microchannel heat exchangers that have high pressure capability, efficient heat transfer, and compact design. A good understanding of two-phase flow of evaporating CO2 in microchannels is needed to analyze and predict heat transfer. A special test rig was built in order to observe two-phase flow patterns, using a horizontal quartz glass tube with ID 0.98 mm, externally coated by a transparent resistive film. Heat flux was obtained by applying DC power to the film, and flow patterns were recorded at 4000 or 8000 frames per second by a digital video camera. Flow patterns were recorded for temperatures 20°C and 0°C, and for mass flux ranging from 100 to 580 kgm−2s−1. The observations showed a dominance of intermittent (slug) flow at low x, and wavy annular flow with entrainment of droplets at higher x. At high mass flux, the annular/entrained flow pattern could be described as dispersed. The aggravated dryout problem reported from heat transfer experiments at high mass flux could be explained by increased entrainment. Stratified flow was not observed in the tests with heat load. Bubble formation and growth could be observed in the liquid film, and the presence of bubbles gave differences in flow pattern compared to adiabatic flow. The flow pattern observations did not fit generalized maps or transition lines showed in the literature.

Sign in / Sign up

Export Citation Format

Share Document