Comparison of Heat Transfer Measurements With Computations for Turbulent Flow Around a 180 deg Bend

1992 ◽  
Vol 114 (4) ◽  
pp. 865-871 ◽  
Author(s):  
D. L. Besserman ◽  
S. Tanrikut
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Turbulent Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Navier Stokes ◽  
Complex Flow ◽  
Wall Functions ◽  
Numerical Predictions ◽  
Fully Developed Turbulent Flow

Results of detailed heat transfer measurements are presented for all four walls of a 180 deg 1:1 aspect ratio duct. Experiments using a transient heat transfer technique with liquid crystal thermography were conducted for turbulent flow over a Reynolds numbers range of 12,500–50,000. Computational results using a Navier–Stokes code are also presented to complement the experiments. Two near-wall shear-stress treatments (wall functions and the two layer wall integration method) were evaluated in conjunction with k–ε formulation of turbulence to assess their ability to predict high local gradients in heat transfer. Results showed that heat transfer on the convex and concave walls is a manifestation of the complex flow field created by the 180 deg bend. For the flat walls, the streamwise average Nusselt number increases to approximately two times the fully developed turbulent flow value. Ninety degrees into the bend, the importance of the cross-stream gradients is evident with the Nusselt number varying from approximately one to three times the fully developed turbulent flow value. The numerical predictions with two-layer wall integration k–ε turbulence model show very good agreement with the experimental data. These results reinforce the need to predict local heat transfer rates accurately in cooling passages of advanced turbine airfoils to enhance the durability of these components.

scholarly journals Comparison of Heat Transfer Measurements With Computations for Turbulent Flow Around a 180 Degree Bend

1991 ◽  
Author(s):  
D. L. Besserman ◽  
S. Tanrikut
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Turbulent Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Navier Stokes ◽  
Complex Flow ◽  
Wall Functions ◽  
Numerical Predictions ◽  
Fully Developed Turbulent Flow

Results of detailed heat transfer measurements are presented for all four walls of a 180° 1:1 aspect ratio duct. Experiments using a transient heat transfer technique with liquid crystal thermography were conducted for turbulent flow over a Reynolds numbers range of 12,500–50,000. Computational results using a Navier-Stokes code are also presented to complement the experiments. Two near-wall shear-stress treatments (wall functions and the two layer wall integration method) were evaluated in conjunction with k-ε formulation of turbulence to assess their ability to predict high local gradients in heat transfer. Results showed that heat transfer on the convex and concave walls is a manifestation of the complex flow field created by the 180° bend. For the flat walls, the streamwise average Nusselt number increases to approximately two times the fully developed turbulent flow value. Ninety degrees into the bend, the importance of the cross-stream gradients is evident with the Nusselt number varying from approximately one to three times the fully developed turbulent flow value. The numerical predictions with two-layer wall integration k-ε turbulence model show very good agreement with the experimental data. These results reinforce the need to accurately predict local heat transfer rates in cooling passages of advanced turbine airfoils to enhance the durability of these components.

Heat Transfer Prediction of a Jet Impinging a Cylindrical Deadlock Area

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Yacine Halouane ◽  
Amina Mataoui ◽  
Farida Iachachene
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flow Behavior ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Potential Core ◽  
Numerical Predictions

The turbulent heat transfer by a confined jet flowing inside a hot cylindrical cavity is investigated numerically in this paper. This configuration is found in several engineering applications such as air conditioning and the ventilation of mines, deadlock, or corridors. The parameters investigated in this work are the Reynolds number (Re, 20,000 ≤ Re ≤ 50,000) and the normalized distance Lf between jet exit and the cavity bottom (Lf, 2 ≤ Lf  ≤ 12). The numerical predictions are performed by finite volume method using the second order one-point closure turbulence model (RSM). The Nusselt number increases and attains maximum values at stagnation points, after it decreases. For an experimental test case available in the literature Lf = 8, the numerical predictions are in good agreement. Processes of heat transfer are analyzed from the flow behavior and the underlying mechanisms. The maximum local heat transfer between the cavity walls and the flow occurs at Lf = 6 corresponding to the length of the potential core. Nusselt number at the stagnation point is correlated versus Reynolds number Re and impinging distance Lf; [Nu0=f(Re,Lf)].

Analysis of Turbulent Flow and Heat Transfer in Internally Finned Tubes and Annuli

1979 ◽  
Vol 101 (1) ◽  
pp. 29-37 ◽  
Author(s):  
S. V. Patankar ◽  
M. Ivanovic´ ◽  
E. M. Sparrow
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Finned Tubes ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Fully Developed Turbulent Flow

The fully developed turbulent flow and heat transfer characteristics for tubes and annuli with longitudinal internal fins were analyzed via a mixing length model. The model takes account of the proximity of both the fin surfaces and the tube wall as well as of the gradients in the radial and circumferential directions. Application was made to air flows, and a single adjustable constant in the model was fixed by comparisons with experimental data for the friction factor and the circumferential-average Nusselt number for internally finned tubes. The local heat transfer coefficients exhibited a substantial variation along the fin height, with the smallest value (essentially zero) at the base and the largest value at the tip. Lesser and more gradual variations were exhibited by the local heat transfer coefficients on the wall of the tube or annulus. In general, the fins were found to be as effective a heat transfer surface as the wall (per unit area). Average Nusselt numbers and friction factors are presented for both the tube and the annulus.

Local Heat Transfer Measurements in Turbulent Flow Around a 180-deg Pipe Bend

1987 ◽  
Vol 109 (1) ◽  
pp. 43-48 ◽  
Author(s):  
J. W. Baughn ◽  
H. Iacovides ◽  
D. C. Jackson ◽  
B. E. Launder
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Secondary Flow ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Pipe Bend ◽  
Streamline Curvature

The paper reports extensive connective heat transfer data for turbulent flow of air around a U-bend with a ratio of bend radius:pipe diameter of 3.375:1. Experiments cover Reynolds numbers from 2 × 104 to 1.1 × 105. Measurements of local heat transfer coefficient are made at six stations and at five circumferential positions at each station. At Re = 6 × 104 a detailed mapping of the temperature field within the air is made at the same stations. The experiment duplicates the flow configuration for which Azzola and Humphrey [3] have recently reported laser-Doppler measurements of the mean and turbulent velocity field. The measurements show a strong augmentation of heat transfer coefficient on the outside of the bend and relatively low levels on the inside associated with the combined effects of secondary flow and the amplification/suppression of turbulent mixing by streamline curvature. The peak level of Nu occurs halfway around the bend at which position the heat transfer coefficient on the outside is about three times that on the inside. Another feature of interest is that a strongly nonuniform Nu persists six diameters downstream of the bend even though secondary flow and streamline curvature are negligible there. At the entry to the bend there are signs of partial laminarization on the inside of the bend, an effect that is more pronounced at lower Reynolds numbers.

Two Dimensional Simulations of Enhanced Heat Transfer in an Intermittently Grooved Channel

2000 ◽  
Author(s):  
M. Greiner ◽  
P. F. Fischer ◽  
H. M. Tufo
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Spectral Element ◽  
Local Heat ◽  
Navier Stokes ◽  
Computational Domain ◽  
Two Dimensional ◽  
Number Range ◽  
Element Technique ◽  
Outflow Boundary

Abstract Two-dimensional Navier-Stokes simulations of heat and momentum transport in an intermittently grooved passage are performed using the spectral element technique for the Reynolds number range 600 ≤ Re ≤ 1800. The computational domain has seven contiguous transverse grooves cut symmetrically into opposite walls, followed by a flat section with the same length. Periodic inflow/outflow boundary conditions are employed. The development and decay of unsteady flow is observed in the grooved and flat sections, respectively. The axial variation of the unsteady component of velocity is compared to the local heat transfer, shear stress and pressure gradient. The results suggest that intermittently grooved passages may offer even higher heat transfer for a given pumping power than the levels observed in fully grooved passages.

Experimental Investigation of the Effect of Synthetic Jets in Minichannels With Subcooled Boiling Flow

2013 ◽  
Author(s):  
David M. Sykes ◽  
Andrew L. Carpenter ◽  
Gregory S. Cole
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Local Heat Transfer ◽  
Local Heat ◽  
High Heat ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Heat Transfer Augmentation

Microchannels and minichannels have been shown to have many potential applications for cooling high-heat-flux electronics over the past 3 decades. Synthetic jets can enhance minichannel performance by adding net momentum flux into a stream without adding mass flux. These jets are produced because of different flow patterns that emerge during the induction and expulsion stroke of a diaphragm, and when incorporated into minichannels can disrupt boundary layers and impinge on the far wall, leading to high heat transfer coefficients. Many researchers have examined the effects of synthetic jets in microchannels and minichannels with single-phase flows. The use of synthetic jets has been shown to augment local heat transfer coefficients by 2–3 times the value of steady flow conditions. In this investigation, local heat transfer coefficients and pressure loss in various operating regimes were experimentally measured. Experiments were conducted with a minichannel array containing embedded thermocouples to directly measure local wall temperatures. The experimental range extends from transitional to turbulent flows. Local wall temperature measurements indicate that increases of heat transfer coefficient of over 20% can occur directly below the synthetic jet with low exit qualities. In this study, the heat transfer augmentation by using synthetic jets was dictated by the momentum ratio of the synthetic jet to the bulk fluid flow. As local quality was increased, the heat transfer augmentation dropped from 23% to 10%. Surface tension variations had a large effect on the Nusselt number, while variations in inertial forces had a small effect on Nusselt number in this operating region.

Inverse Determination of the Local Heat Transfer Coefficients for Nucleate Boiling on a Horizontal Cylinder

2003 ◽  
Vol 125 (6) ◽  
pp. 1087-1095 ◽  
Author(s):  
H. Louahlia-Gualous ◽  
P. K. Panday ◽  
E. A. Artioukhine
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pool Boiling ◽  
Gradient Methods ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Nucleate Boiling ◽  
Nucleate Pool Boiling ◽  
Transfer Coefficients ◽  
Iterative Regularization

This article treats the local heat transfer for nucleate pool boiling around the cylinder using the inverse heat conduction analysis. The physical model considers a half section of a cylinder with unknown surface temperature and heat flux density. The iterative regularization and the conjugate gradient methods are used for solving the inverse analysis. The local Nusselt number profiles for nucleate pool boiling are presented and analyzed for different electric heat. The mean Nusselt number estimated by IHCP is closed with the measured values. The results of IHCP are compared to those of Cornewell and Houston (1994), Stephan and Abdelsalam (1980) and Memory et al. (1995). The influence of the error of the measured temperatures and the error in placement of the thermocouples are studied.

Effect of Periodicity of Non-Uniform Sinusoidal Side Heating on Natural Convection in an Anisotropic Porous-Enclosure

2011 ◽  
Vol 110-116 ◽  
pp. 1613-1618 ◽  
Author(s):  
S. Kapoor ◽  
P. Bera
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Stream Function ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Porous Enclosure

A comprehensive numerical study on the natural convection in a hydrodynamically anisotropic as well as isotropic porous enclosure is presented, flow is induced by non uniform sinusoidal heating of the right wall of the enclosure. The principal directions of the permeability tensor has been taken oblique to the gravity vector. The spectral Element method has been adopted to solve numerically the governing differential equations by using the vorticity-stream-function approach. The results are presented in terms of stream function, temperature profile and Nusselt number. The result show that the maximum heat transfer takes place at y = 1.5 when N is odd.. Also, increasing media permeability, by changing K* = 1 to K* = 0.2, increases heat transfer rate at below and above right corner of the enclosure. Furthermore, for the all values of N, profiles of local Nusselt number (Nuy) in isotropic as well as anisotropic media are similar, but for even values of N differ slightly at N = 2.. In particular the present analysis shows that, different periodicity (N) of temperature boundary condition has the significant effect on the flow pattern and consequently on the local heat transfer phenomena.

Numerical Investigation of Heat Transfer for Laminar and Turbulent Flow in a Plate Heat Exchanger

2010 ◽  
Author(s):  
Iulian Gherasim ◽  
Nicolas Galanis ◽  
Cong Tam Nguyen
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Turbulent Flow ◽  
Complex Geometry ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Plate Heat Exchanger ◽  
Plate Heat ◽  
Laminar And Turbulent Flow ◽  
Channel Plate

The problem of turbulent flow and heat transfer in a two-channel plate heat exchanger was numerically investigated, considering its complex geometry as well as inlet and outlet ports effects. Results obtained for the flow and thermal field have clearly shown their asymmetrical behavior, which has important influence on the local heat transfer. Friction factor are found to be in good agreement with theoretical correlation.

Local Heat Transfer Coefficients Under an Axisymmetric, Single-Phase Liquid Jet

1991 ◽  
Vol 113 (1) ◽  
pp. 71-78 ◽  
Author(s):  
J. Stevens ◽  
B. W. Webb
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Local Nusselt Number ◽  
Single Phase ◽  
Radial Distance ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Plate Spacing

The purpose of this investigation was to characterize local heat transfer coefficients for round, single-phase free liquid jets impinging normally against a flat uniform heat flux surface. The problem parameters investigated were jet Reynolds number Re, nozzle-to-plate spacing z, and jet diameter d. A region of near-constant Nusselt number was observed for the region bounded by 0≤r/d≤0.75, where r is the radial distance from the impingement point. The local Nusselt number profiles exhibited a sharp drop for r/d > 0.75, followed by an inflection and a slower decrease there-after. Increasing the nozzle-to-plate spacing generally decreased the heat transfer slightly. The local Nusselt number characteristics were found to be dependent on nozzle diameter. This was explained by the influence of the free-stream velocity gradient on local heat transfer, as predicted in the classical analysis of infinite jet stagnation flow and heat transfer. Correlations for local and average Nusselt numbers reveal an approximate Nusselt number dependence on Re1/3.

Sign in / Sign up

Export Citation Format

Share Document