Unsteady Wake Over a Linear Turbine Blade Cascade With Air and CO2 Film Injection: Part I—Effect on Heat Transfer Coefficients

1994 ◽  
Vol 116 (4) ◽  
pp. 721-729 ◽  
Author(s):  
S. Ou ◽  
J.-C. Han ◽  
A. B. Mehendale ◽  
C. P. Lee
Keyword(s):  
Heat Transfer ◽  
Transition Region ◽  
Density Ratio ◽  
Wake Flow ◽  
Transfer Coefficients ◽  
Pressure Surface ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Nusselt Numbers ◽  
Unsteady Wake

The effect of unsteady wake flow and air (D.R. = 1.0) or CO2 (D.R. = 1.52) film injection on blade heat transfer coefficients was experimentally determined. A spoked wheel-type wake generator produced the unsteady wake. Experiments were performed on a five-airfoil linear cascade in a low-speed wind tunnel at the chord Reynolds number of 3 × 105 for the no-wake case and at the wake Strouhal numbers of 0.1 and 0.3. Results from a blade with three rows of film holes in the leading edge region and two rows each on the pressure and suction surfaces show that the Nusselt numbers are much higher than those for the blade without film holes. On a large portion of the blade, the Nusselt numbers “without wake but with film injection” are much higher than for “with wake but no film holes.” An increase in wake Strouhal number causes an increase in pressure surface Nusselt numbers; but the increases are reduced at higher blowing ratios. As blowing ratio increases, the Nusselt numbers for both density ratio injectants (air and CO2) increase over the entire blade except for the transition region where the effect is reversed. Higher density injectant (CO2) produces lower Nusselt numbers on the pressure surface, but the numbers for air and CO2 injections are very close on the suction surface except for the transition region where the numbers for CO2 injection are higher. From this study, one may conclude that the additional increases in Nusselt numbers due to unsteady wake, blowing ratio, and density ratio are only secondary when compared to the dramatic increases in Nusselt numbers only due to film injection over the no film holes case.

scholarly journals Unsteady Wake Over a Linear Turbine Blade Cascade With Air and CO2 Film Injection: Part I — Effect on Heat Transfer Coefficients

1993 ◽  
Author(s):  
Shichuan Ou ◽  
Je-Chin Han ◽  
Anant B. Mehendale ◽  
C. Pang Lee
Keyword(s):  
Heat Transfer ◽  
Transition Region ◽  
Density Ratio ◽  
Wake Flow ◽  
Transfer Coefficients ◽  
Pressure Surface ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Nusselt Numbers ◽  
Unsteady Wake

The effect of unsteady wake flow and air (D.R.=1.0) or CO2 (D.R.=1.52) film injection on blade heat transfer coefficients was experimentally determined. A spoked wheel type wake generator produced the unsteady wake. Experiments were performed on a five airfoil linear cascade in a low speed wind tunnel at the chord Reynolds number of 3×105 for the no wake case and at the wake Strouhal numbers of 0.1 and 0.3. Results from a blade with three rows of film holes in the leading edge region and two rows each on the pressure and suction surfaces show that the Nusselt numbers are much higher than those for the blade without film holes. On a large portion of the blade, the Nusselt numbers ‘without wake but with film injection’ are much higher than for ‘with wake but no film holes’. An increase in wake Strouhal number causes an increase in pressure surface Nusselt numbers; but the increases reduce at higher blowing ratios. As blowing ratio increases, the Nusselt numbers for both density ratio injectants (air and CO2) increase over the entire blade except for the transition region where the effect is reversed. Higher density injectant (CO2) produces lower Nusselt numbers on the pressure surface, but the numbers for air and CO2 injections are very close on the suction surface except for the transition region where the numbers for CO2 injection are higher. From this study, one may conclude that the additional increases in Nusselt numbers due to unsteady wake, blowing ratio, and density ratio are only secondary when compared to the dramatic increases in Nusselt numbers only due to film injection over the no film holes case.

Unsteady Wake Effect on Film Effectiveness and Heat Transfer Coefficient From a Turbine Blade With One Row of Air and CO2 Film Injection

1994 ◽  
Vol 116 (4) ◽  
pp. 921-928 ◽  
Author(s):  
S. Ou ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Strouhal Number ◽  
Turbine Blade ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Suction Surface ◽  
Wake Effect ◽  
Pressure Surface ◽  
Heat Transfer Coefficients ◽  
Unsteady Wake

The effect of unsteady wake and film injection on heat transfer coefficients and film effectiveness from a gas turbine blade was found experimentally. A spoked wheel type wake generator produced the unsteady flow. Experiments were done with a five airfoil linear cascades in a low-speed wind tunnel at a chord Reynolds number of 3 × 105, two wake Strouhal numbers of 0.1 and 0.3, and a no-wake case. A model turbine blade injected air or CO2 through one row of film holes each on the pressure and suction surfaces. The results show that the large-density injectant (CO2) causes higher heat transfer coefficients on the suction surface and lower heat transfer coefficients on the pressure surface. At the higher blowing ratios of 1.0 and 1.5, the film effectiveness increases with increasing injectant-to-mainstream density ratio at a given Strouhal number. However, the density ratio effect on film effectiveness is reversed at the lowest blowing ratio of 0.5. Higher wake Strouhal numbers enhance the heat transfer coefficients but reduce film effectiveness for both density ratio injectants at all three blowing ratios. The effect of the wake Strouhal number on the heat transfer coefficients on the suction surface is greater than that on the pressure surface.

Heat Transfer Coefficients Over a Flat Surface With Air and CO2 Injection Through Compound Angle Holes Using a Transient Liquid Crystal Image Method

1995 ◽  
Author(s):  
Srinath V. Ekkad ◽  
Dyrk Zapata ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Flat Surface ◽  
Density Ratio ◽  
Test Surface ◽  
Image Method ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Compound Angle

This paper presents the detailed heat transfer coefficients over a flat surface with one row of injection holes inclined streamwise at 35° for three blowing ratios (M=0.5–2.0). Three compound angles of 0°, 45°, and 90° with air (D.R.=0.98) and CO2 (D.R.=1.46) as coolants were tested at an elevated free-stream turbulence condition (Tu≈8.5%). The experimental technique involves a liquid crystal coating on the test surface. Two related transient tests obtained detailed heat transfer coefficients and film effectiveness distributions. Heat transfer coefficients increase with increasing blowing ratio for a constant density ratio but decrease with increasing density ratio for a constant blowing ratio. Heat transfer coefficients increase for both coolants over the test surface as the compound angle increases from 0° to 90°. The detailed heat transfer coefficients obtained using the transient liquid crystal technique, particularly in the near hole region, will provide a better understanding of the film cooling process in gas turbine components.

Heat Transfer Coefficients Over a Flat Surface With Air and CO2 Injection Through Compound Angle Holes Using a Transient Liquid Crystal Image Method

1997 ◽  
Vol 119 (3) ◽  
pp. 580-586 ◽  
Author(s):  
S. V. Ekkad ◽  
D. Zapata ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Flat Surface ◽  
Density Ratio ◽  
Test Surface ◽  
Image Method ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio ◽  
Compound Angle

This paper presents the detailed heat transfer coefficients over a flat surface with one row of injection holes inclined streamwise at 35 deg for three blowing ratios (M = 0.5–2.0). Three compound angles of 0, 45, and 90 deg with air (D.R. = 0.98) and CO2 (D.R. = 1.46) as coolants were tested at an elevated free-stream turbulence condition (Tu ≈ 8.5 percent). The experimental technique involves a liquid crystal coating on the test surface. Two related transient tests obtained detailed heat transfer coefficients and film effectiveness distributions. Heat transfer coefficients increase with increasing blowing ratio for a constant density ratio, but decrease with increasing density ratio for a constant blowing ratio. Heat transfer coefficients increase for both coolants over the test surface as the compound angle increases from 0 to 90 deg. The detailed heat transfer coefficients obtained using the transient liquid crystal technique, particularly in the near-hole region, will provide a better understanding of the film cooling process in gas turbine components.

Heat Transfer in a Surfactant Drag-Reducing Solution—A Comparison With Predictions for Laminar Flow

2005 ◽  
Vol 128 (6) ◽  
pp. 557-563 ◽  
Author(s):  
Paul L. Sears ◽  
Libing Yang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Reynolds Numbers ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Drag Reducing Additive ◽  
Good Agreement

Heat transfer coefficients were measured for a solution of surfactant drag-reducing additive in the entrance region of a uniformly heated horizontal cylindrical pipe with Reynolds numbers from 25,000 to 140,000 and temperatures from 30to70°C. In the absence of circumferential buoyancy effects, the measured Nusselt numbers were found to be in good agreement with theoretical results for laminar flow. Buoyancy effects, manifested as substantially higher Nusselt numbers, were seen in experiments carried out at high heat flux.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

scholarly journals Heat Transfer Measurements for Rotating Turbine Discs

1989 ◽  
Author(s):  
G. Qureshi ◽  
M. H. Nguyen ◽  
N. R. Saad ◽  
R. N. Tadros
Keyword(s):  
Heat Transfer ◽  
Coolant Flow ◽  
Flow Conditions ◽  
Transfer Coefficients ◽  
Rotating Disc ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Rotating Discs ◽  
Turbine Disc ◽  
State Technique

To optimise the turbine disc weight and coolant flow requirements, the aspect of improving thermal analysis was investigated. As a consequence, an experimental investigation was undertaken to measure the rates of convective heat transfer. The constant temperature steady state technique was used to determine the local and average heat transfer coefficients on the sides of rotating discs. The effects of coolant flow rates, CW (3000 ≤ CW ≤ 18600) with two types of cavity in-flow conditions and of the rotational speeds, Reθ (from 4×105 to 1.86×106) on the disc heat transfer were studied and correlations developed. For a rotating disc in confined cavities with superimposed coolant flows, Nusselt numbers were found to be higher than those for the free rotating disc without confinement.

scholarly journals The Superposition Approach to Local Heat Transfer Coefficients in High Density Ratio Film Cooling Flows

1999 ◽  
Author(s):  
Michael Gritsch ◽  
Stefan Baldauf ◽  
Moritz Martiny ◽  
Achmed Schulz ◽  
Sigmar Wittig
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Film Cooling ◽  
Density Ratio ◽  
Two Dimensional ◽  
Transfer Coefficients ◽  
Cooling Flows ◽  
Heat Transfer Coefficients ◽  
High Density Ratio ◽  
The Heat Transfer Coefficient

The present paper reports on the use of the superposition approach in high density ratio film cooling flows. It arises from the linearity and homogeneity of the simplified boundary layer differential equations. However, it is widely assumed that the linearity does not hold for variable property flows. Therefore, theoretical considerations and numerical calculations will demonstrate the linearity of the heat transfer coefficient with the dimensionless coolant temperature θ as long as identical flow conditions are applied. This makes it necessary to perform at least two experiments at different θ but with the coolant to main flow temperature ratio kept unchanged. A comprehensive set of experiments is presented to demonstrate the capability of the superposition approach for determining heat transfer coefficients for different film cooling geometries. These comprise coolant injection from two dimensional tangential slots, single holes, and rows of cylindrical holes. Particularly, two dimensional local distributions of the heat transfer coefficient will be addressed.

Conjugate Heat Transfer in Air-to-Refrigerant Airfoil Heat Exchangers

2014 ◽  
Vol 136 (8) ◽  
Author(s):  
Yutaka Ito ◽  
Naoya Inokura ◽  
Takao Nagasaki
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Heat Exchangers ◽  
Transfer Coefficients ◽  
Exchange System ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Heat Exchange System ◽  
Inverse Heat Transfer ◽  
Transfer Method

A light and compact heat exchange system was realized using two air-to-refrigerant airfoil heat exchangers and a recirculated heat transport refrigerant. Its heat transfer performance was experimentally investigated. Carbon dioxide or water was used as a refrigerant up to a pressure of 30 MPa. Heat transfer coefficients on the outer air-contact and inner refrigerant-contact surfaces were calculated using an inverse heat transfer method. Correlations were developed for the Nusselt numbers of carbon dioxide and water on the inner refrigerant-contact surface. Furthermore, we proposed a method to evaluate a correction factor corresponding to the thermal resistance of the airfoil heat exchanger.

Latticework (Vortex) Cooling Effectiveness: Part 2 — Rotating Channel Experiments

2004 ◽  
Author(s):  
S. Acharya ◽  
Fuguo Zhou ◽  
Jonathan Lagrone ◽  
Gazi Mahmood ◽  
Ronald S. Bunker
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Performance Factors ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Smooth Channel ◽  
Rib Turbulators ◽  
Density Ratios

The heat transfer and pressure drop characteristics of latticework coolant blade passages have been investigated experimentally under conditions of rotation. Stationary studies with the latticework configuration have shown potential advantages including spatially-uniform streamwise distributions of the heat transfer coefficient, greater blade strength, and enhancement levels comparable to conventional rib turbulators. In the present study, a latticework coolant passage, with orthogonal-ribs, is studied in a rotating heat transfer test-rig for a range of Reynolds numbers (Res), Rotation numbers (Ros), and density ratios. Measurements indicate that for Res≥20,000, the latticework coolant passage provides very uniform streamwise distributions of the Nusselt number (Nus) with enhancement levels (relative to smooth-channel values) in the range of 2.0 to 2.5. No significant dependence of Nus on Ros and density ratio is observed except at lower Res values (≤10,000). Nusselt numbers are highest immediately downstream of a turn indicating that bend-effects play a major role in enhancing heat transfer. Friction factors are relatively insensitive to Ros, and thermal performance factors at higher Res values appear to be comparable to those obtained with conventional rib-turbulators. The present study indicates that latticework cooling geometry can provide comparable heat transfer enhancements and thermal performance factors as conventional rib-turbulators, with potential benefits of streamwise uniformity in the heat transfer coefficients and added blade strength.

Sign in / Sign up

Export Citation Format

Share Document