Dynamic Plastic Response of Circular Plates With Transverse Shear and Rotatory Inertia

1980 ◽  
Vol 47 (1) ◽  
pp. 27-34 ◽  
Author(s):  
Norman Jones ◽  
J. Gomes de Oliveira
Keyword(s):  
Transverse Shear ◽  
Plastic Material ◽  
Yield Criterion ◽  
Circular Plates ◽  
Plastic Response ◽  
Governing Equations ◽  
Rotatory Inertia ◽  
Perfectly Plastic ◽  
Shear Effects ◽  
Transverse Shear Effects

The response of a simply supported circular plate made from a rigid perfectly plastic material and subjected to a uniformly distributed impulsive velocity is developed herein. Plastic yielding of the material is controlled by a yield criterion which retains the transverse shear force as well as bending moments and the influence of rotatory inertia is included in the governing equations. Various equations and numerical results are presented which may be used to assess the importance of transverse shear effects and rotatory inertia for this particular problem.

The Influence of Rotatory Inertia and Transverse Shear on the Dynamic Plastic Behavior of Beams

1979 ◽  
Vol 46 (2) ◽  
pp. 303-310 ◽  
Author(s):  
Norman Jones ◽  
J. Gomes de Oliveira
Keyword(s):  
Transverse Shear ◽  
Shear Force ◽  
Yield Criterion ◽  
Yield Condition ◽  
Bending Moment ◽  
Plastic Behavior ◽  
Plastic Response ◽  
Rotatory Inertia ◽  
Perfectly Plastic ◽  
Theoretical Procedure

The theoretical procedure presented herein examines the influence of retaining the transverse shear force in the yield criterion and rotatory inertia on the dynamic plastic response of beams. Exact theoretical rigid perfectly plastic solutions are presented for a long beam impacted by a mass and a simply supported beam loaded impulsively. It transpires that rotatory inertia might play a small, but not negligible, role on the response of these beams. The results in the various figures indicate that the greatest departure from an analysis which neglects rotatory inertia but retains the influence of the bending moment and transverse shear force in the yield condition is approximately 11 percent for the particular range of parameters considered.

A limit load solution for a thick-walled cylinder with a fully circumferential crack under axial tension

2009 ◽  
Vol 44 (6) ◽  
pp. 407-416 ◽  
Author(s):  
P J Budden ◽  
Y Lei
Keyword(s):  
Finite Element ◽  
Plastic Material ◽  
Yield Criterion ◽  
Limit Load ◽  
Cylinder Wall ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic ◽  
Von Mises ◽  
Inside Radius ◽  
Walled Cylinder

Limit loads for a thick-walled cylinder with an internal or external fully circumferential surface crack under pure axial load are derived on the basis of the von Mises yield criterion. The solutions reproduce the existing thin-walled solution when the ratio between the cylinder wall thickness and the inside radius tends to zero. The solutions are compared with published finite element limit load results for an elastic–perfectly plastic material. The comparison shows that the theoretical solutions are conservative and very close to the finite element data.

Free-Vibration of Rotating Composite Beams Incorporating Higher-Order Transverse Shear Effects

2001 ◽  
Author(s):  
N. K. Chandiramani ◽  
L. I. Librescu ◽  
C. D. Shete
Keyword(s):  
Free Vibration ◽  
Transverse Shear ◽  
Present Model ◽  
Structural Model ◽  
Laminated Composite ◽  
Higher Order ◽  
Rotating Blade ◽  
Box Beam ◽  
Shear Effects ◽  
Transverse Shear Effects

Abstract The free vibration behavior of a rotating blade modeled as a laminated composite hollow (single celled) box beam is studied. The geometrically nonlinear structural model developed herein incorporates a number of non-classical effects such as anisotropy, heterogeneity, transverse shear flexibility, and warping inhibition. The centrifugal and Coriolis force field effects are also included. The main focus here being the refinement of the existing model, the traction-free boundary conditions are satisfied here in contrast to the existing model. The resulting linearized equations and numerical results based on them are presented. Results obtained for the present higher-order shearable model are compared with those of the existing first-order shearable and the non-shearable models. Tailoring studies using the present model reveal an enhancement of eigenfrequency characteristics.

Sign in / Sign up

Export Citation Format

Share Document