A limit load solution for a thick-walled cylinder with a fully circumferential crack under axial tension

2009 ◽  
Vol 44 (6) ◽  
pp. 407-416 ◽  
Author(s):  
P J Budden ◽  
Y Lei
Keyword(s):  
Finite Element ◽  
Plastic Material ◽  
Yield Criterion ◽  
Limit Load ◽  
Cylinder Wall ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic ◽  
Von Mises ◽  
Inside Radius ◽  
Walled Cylinder

Limit loads for a thick-walled cylinder with an internal or external fully circumferential surface crack under pure axial load are derived on the basis of the von Mises yield criterion. The solutions reproduce the existing thin-walled solution when the ratio between the cylinder wall thickness and the inside radius tends to zero. The solutions are compared with published finite element limit load results for an elastic–perfectly plastic material. The comparison shows that the theoretical solutions are conservative and very close to the finite element data.

The ratchetting of a cylinder subjected to internal pressure and alternating axial deformation

1993 ◽  
Vol 28 (4) ◽  
pp. 277-282 ◽  
Author(s):  
D N Moreton
Keyword(s):  
Internal Pressure ◽  
Wall Thickness ◽  
Plastic Material ◽  
Yield Criterion ◽  
Axial Deformation ◽  
Simple Experiment ◽  
Perfectly Plastic ◽  
Thin Walled ◽  
Elastic Perfectly Plastic ◽  
Walled Cylinder

A thin-walled cylinder subjected to a continuous internal pressure and an alternating axial deformation is shown to exhibit ratchetting. This ratchetting manifests itself as a growth in the diameter of the cylinder and a reduction in its wall thickness. For an elastic-perfectly-plastic material the ratchetting rates are established and the boundaries of ratchetting behaviour determined. These ratchetting rates are compared with the results from a simple experiment and other available data. It is noted that the analysis is very sensitive to the yield criterion adopted.

Elasto-Plastic Coupled Temperature-Displacement Finite Element Analysis of Two-Dimensional Rolling-Sliding Contact With a Translating Heat Source

1991 ◽  
Vol 113 (1) ◽  
pp. 93-101 ◽  
Author(s):  
S. M. Kulkarni ◽  
C. A. Rubin ◽  
G. T. Hahn
Keyword(s):  
Finite Element ◽  
Half Space ◽  
Plastic Material ◽  
Element Model ◽  
Rolling Contact ◽  
Two Dimensional ◽  
Element Analysis ◽  
Element Mesh ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

The present paper, describes a transient translating elasto-plastic thermo-mechanical finite element model to study 2-D frictional rolling contact. Frictional two-dimensional contact is simulated by repeatedly translating a non-uniform thermo-mechanical distribution across the surface of an elasto-plastic half space. The half space is represented by a two dimensional finite element mesh with appropriate boundaries. Calculations are for an elastic-perfectly plastic material and the selected thermo-physical properties are assumed to be temperature independent. The paper presents temperature variations, stress and plastic strain distributions and deformations. Residual tensile stresses are observed. The magnitude and depth of these stresses depends on 1) the temperature gradients and 2) the magnitudes of the normal and tangential tractions.

Shakedown Limit Load Determination for a Kinematically Hardening 90-Degree Pipe Bend Subjected to Constant Internal Pressure and Cyclic Bending

2007 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Plastic Material ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Material Behavior ◽  
Pipe Bend ◽  
Cyclic Bending ◽  
Perfectly Plastic ◽  
Shakedown Limit

A simplified technique for determining the shakedown limit load of a structure employing an elastic-perfectly-plastic material behavior was previously developed and successfully applied to a long radius 90-degree pipe bend. The pipe bend is subjected to constant internal pressure and cyclic bending. The cyclic bending includes three different loading patterns namely; in-plane closing, in-plane opening, and out-of-plane bending moment loadings. The simplified technique utilizes the finite element method and employs small displacement formulation to determine the shakedown limit load without performing lengthy time consuming full cyclic loading finite element simulations or conventional iterative elastic techniques. In the present paper, the simplified technique is further modified to handle structures employing elastic-plastic material behavior following the kinematic hardening rule. The shakedown limit load is determined through the calculation of residual stresses developed within the pipe bend structure accounting for the back stresses, determined from the kinematic hardening shift tensor, responsible for the translation of the yield surface. The outcomes of the simplified technique showed very good correlation with the results of full elastic-plastic cyclic loading finite element simulations. The shakedown limit moments output by the simplified technique are used to generate shakedown diagrams of the pipe bend for a spectrum of constant internal pressure magnitudes. The generated shakedown diagrams are compared with the ones previously generated employing an elastic-perfectly-plastic material behavior. These indicated conservative shakedown limit moments compared to the ones employing the kinematic hardening rule.

Analytical Solutions of Crack Tip Plasticity Zone Shape for a Semi-Infinite Crack

2003 ◽  
Author(s):  
Peihua Jing ◽  
Tariq Khraishi ◽  
Larissa Gorbatikh
Keyword(s):  
Plane Strain ◽  
Plane Stress ◽  
Analytical Solutions ◽  
Yield Criterion ◽  
Plasticity Zone ◽  
Linear Elastic ◽  
Perfectly Plastic ◽  
Classical Plasticity ◽  
Elastic Perfectly Plastic ◽  
Von Mises

In this work, closed-form analytical solutions for the plasticity zone shape at the lip of a semi-infinite crack are developed. The material is assumed isotropic with a linear elastic-perfectly plastic constitution. The solutions have been developed for the cases of plane stress and plane strain. The three crack modes, mode I, II and III have been considered. Finally, prediction of the plasticity zone extent has been performed for both the Von Mises and Tresca yield criterion. Significant differences have been found between the plane stress and plane strain conditions, as well as between the three crack modes’ solutions. Also, significant differences have been found when compared to classical plasticity zone calculations using the Irwin approach.

A Finite Element Based Study on the Elastic-Plastic Transition Behavior in a Hemisphere in Contact With a Rigid Flat

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
S. Shankar ◽  
M. M. Mayuram
Keyword(s):  
Finite Element ◽  
Contact Area ◽  
Plastic Material ◽  
Plastic Region ◽  
Real Contact Area ◽  
Real Contact ◽  
Perfectly Plastic ◽  
The Difference ◽  
Elastic Perfectly Plastic ◽  
Green Model

An axisymmetrical hemispherical asperity in contact with a rigid flat is modeled for an elastic perfectly plastic material. The present analysis extends the work (sphere in contact with a flat plate) of Kogut–Etsion Model and Jackson–Green Model and addresses some aspects uncovered in the above models. This paper shows the critical values in the dimensionless interference ratios (ω∕ωc) for the evolution of the elastic core and the plastic region within the asperity for different Y∕E ratios. The present analysis also covers higher interference ratios, and the results are applied to show the difference in the calculation of real contact area for the entire surface with other existing models. The statistical model developed to calculate the real contact area and the contact load for the entire surfaces based on the finite element method (FEM) single asperity model with the elastic perfectly plastic assumption depends on the Y∕E ratio of the material.

Shakedown Limits of a 90-Degree Pipe Bend Using Small and Large Displacement Formulations

2006 ◽  
Author(s):  
Hany F. Abdalla ◽  
Mohammad M. Megahed ◽  
Maher Y. A. Younan
Keyword(s):  
Plastic Material ◽  
Limit Load ◽  
Material Model ◽  
Large Displacement ◽  
Small Displacement ◽  
Pipe Bend ◽  
Perfectly Plastic ◽  
Loading Patterns ◽  
Elastic Perfectly Plastic ◽  
Shakedown Limit

In this paper the shakedown limit load is determined for a long radius 90-degree pipe bend using two different techniques. The first technique is a simplified technique which utilizes small displacement formulation and elastic-perfectly-plastic material model. The second technique is an iterative based technique which uses the same elastic-perfectly-plastic material model, but incorporates large displacement effects accounting for geometric non-linearity. Both techniques use the finite element method for analysis. The pipe bend is subjected to constant internal pressure magnitudes and cyclic bending moments. The cyclic bending loading includes three different loading patterns namely; in-plane closing, in-plane opening, and out-of-plane bending. The simplified technique determines the shakedown limit load (moment) without the need to perform full cyclic loading simulations or conventional iterative elastic techniques. Instead, the shakedown limit moment is determined by performing two analyses namely; an elastic analysis and an elastic-plastic analysis. By extracting the results of the two analyses, the shakedown limit moment is determined through the calculation of the residual stresses developed in the pipe bend. The iterative large displacement technique determines the shakedown limit moment in an iterative manner by performing a series of full elastic-plastic cyclic loading simulations. The shakedown limit moment output by the simplified technique (small displacement) is used by the iterative large displacement technique as an initial iterative value. The iterations proceed until an applied moment guarantees a structure developed residual stress, at load removal, equals or slightly less than the material yield strength. The shakedown limit moments output by both techniques are used to generate shakedown diagrams of the pipe bend for a spectrum of constant internal pressure magnitudes for the three loading patterns stated earlier. The maximum moment carrying capacity (limit moment) the pipe bend can withstand and the elastic limit are also determined and imposed on the shakedown diagram of the pipe bend. Comparison between the shakedown diagrams generated by the two techniques, for the three loading patterns, is presented.

Application of a Sixth Order Generalized Stress Function for Determining Limit Loads for Plates with Triangular Penetration Patterns

2002 ◽  
Author(s):  
J. L. Gordon ◽  
D. P. Jones
Keyword(s):  
Finite Element ◽  
Fourth Order ◽  
Limit Load ◽  
Sixth Order ◽  
Numerical Representation ◽  
Order Function ◽  
Practical Applications ◽  
Perfectly Plastic ◽  
Unit Cells ◽  
Elastic Perfectly Plastic

The capability to obtain limit load solutions of plates with triangular penetration patterns using fourth order functions to represent the collapse surface has been presented in previous papers. These papers describe how equivalent solid plate elastic-perfectly plastic finite element capabilities are generated and demonstrate how such capabilities can be used to great advantage in the analysis of tubesheets in large heat exchanger applications. However, these papers have pointed out that although the fourth order functions can produce sufficient accuracy for many practical applications, there are situations where improvements in the accuracy of in-plane and transverse shear are desirable. This paper investigates the use of a sixth order function to represent the collapse surface for improved accuracy of the in-plane response. Explicit elastic-perfectly plastic finite element solutions are obtained for unit cells representing an infinite array of circular penetrations arranged in an equilateral triangular array. These cells are used to create a numerical representation of the complete collapse surfaces for a number of ligament efficiencies (h/P where h is the minimum ligament width and P is the distance between hole centers). Each collapse surface is then fit to a sixth order function that satisfies the periodicity of the hole pattern. Sixth-order collapse functions were developed for h/P values between .05 and .50. Accuracy of the sixth order and the fourth order functions are compared. It was found that the sixth order function is indeed more accurate, reducing the error from 12.2% for the fourth order function to less than 3% for the sixth order function.

Effects of Torsion on Equivalent Bending Moment for Limit Load and EPFM Circumferential Pipe Flaw Evaluations

2012 ◽  
Vol 134 (6) ◽  
Author(s):  
Phuong H. Hoang ◽  
Kunio Hasegawa ◽  
Bostjan Bezensek ◽  
Yinsheng Li
Keyword(s):  
Finite Element ◽  
Pressure Vessel ◽  
Large Strain ◽  
Bending Moment ◽  
Limit Load ◽  
Elastic Plastic ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Weighted Factor ◽  
Elastic Perfectly Plastic

The circumferential flaw evaluation procedures in ASME Boiler and Pressure Vessel Code Section XI nonmandatory Appendix C are currently limited to straight pipes under pressure and bending loads without consideration of torsion loading. The Working Group on Pipe Flaw Evaluation of the ASME Boiler and Pressure Vessel Code is developing guidance for considering the effects of torsion by a mean of an equivalent bending moment, which is a square root of sum square combination of bending moment and torsion load with a weighted factor for torsion moment. A torsion weighted factor, Ce, is established in this paper using large strain finite element limit load analysis with elastic perfectly plastic materials. Planar flaws and nonplanar flaws in a 10.75 in. (273 mm) OD pipe are investigated. Additionally, a finite element J-integral calculation is performed for a planar through wall circumferential flaw with elastic plastic materials subjected to bending and torsion load combinations. The proposed Ce factor for planar flaws is intended for use with the ASME B&PV Code Section XI, Appendix C for limit load and Elastic Plastic Fracture Mechanics (EPFM) circumferential planar flaw evaluations.

Elasto-Plastic Asperity Contacts of Layered Media

2005 ◽  
Author(s):  
Qin Xie ◽  
Geng Liu ◽  
Tianxiang Liu ◽  
Ruiting Tong ◽  
Quanren Zeng
Keyword(s):  
Yield Criterion ◽  
Layered Media ◽  
Asperity Contact ◽  
Initial Stiffness ◽  
Programming Technique ◽  
Perfectly Plastic ◽  
Real Area Of Contact ◽  
Asperity Contacts ◽  
Elastic Perfectly Plastic ◽  
Von Mises

An elasto-plastic asperity contact model for layered media is developed in the work reported in this paper to analyze the influences of coating-substrate materials on contact when yielding and the strain-hardening properties of materials are taken into account. The finite element method, the initial stiffness method and the mathematical programming technique are employed to solve the model. The von Mises yield criterion is used to determine the inception of plastic deformation. The effects of different layer thickness and different coating-substrate materials on the contact pressure, real area of contact, average gap of rough surface, and stresses in layer and substrate under the elastic-perfectly-plastic and the elasto-plastic contact conditions are numerically investigated and discussed.

Plastic Limit Loads for Through-Wall Cracked Pipes Using Finite Element Limit Analysis

2006 ◽  
Vol 321-323 ◽  
pp. 724-728
Author(s):  
Nam Su Huh ◽  
Yoon Suk Chang ◽  
Young Jin Kim
Keyword(s):  
Finite Element ◽  
Limit Analysis ◽  
Structural Integrity ◽  
Three Dimensional ◽  
Limit Load ◽  
Plastic Behavior ◽  
Plastic Limit ◽  
Integrity Assessment ◽  
Perfectly Plastic ◽  
Elastic Perfectly Plastic

The present paper provides plastic limit load solutions for axial and circumferential through-wall cracked pipes based on detailed three-dimensional (3-D) finite element (FE) limit analysis using elastic-perfectly plastic behavior. As a loading condition, both single and combined loadings are considered. Being based on detailed 3-D FE limit analysis, the present solutions are believed to be valuable information for structural integrity assessment of cracked pipes.

Sign in / Sign up

Export Citation Format

Share Document