The Leading-Edge-Groove Tilting-Pad Thrust Bearing: Recent Developments

1985 ◽  
Vol 107 (3) ◽  
pp. 423-428 ◽  
Author(s):  
A. M. Mikula
Keyword(s):  
Experimental Data ◽  
Power Loss ◽  
Thrust Bearing ◽  
Leading Edge ◽  
Thrust Bearings ◽  
Temperature Performance ◽  
Tilting Pad ◽  
Recent Developments ◽  
Bearing Design

This paper compares the leading edge groove and pressurized supply (flooded) lubricant supply methods, and analyzes their influence on the performance of equalizing tilting pad thrust bearings. This paper presents new experimental data on 6-shoe, 267 mm (10 1/2 in.) O.D. bearings, operating at shaft speeds up to 14000 rpm, with loads ranging up to 3.45 MPa (500 psi) for two different lubricants. The data presented details the power loss and babbitt temperature performance of two versions of the leading-edge-groove bearing design and contrasts the results with a pressurized supply bearing design.

A Comparison of Tilting Pad Thrust Bearing Lubricant Supply Methods

1983 ◽  
Vol 105 (1) ◽  
pp. 39-45 ◽  
Author(s):  
A. M. Mikula ◽  
R. S. Gregory
Keyword(s):  
Experimental Data ◽  
Power Loss ◽  
Thrust Bearing ◽  
Leading Edge ◽  
Potential User ◽  
Thrust Bearings ◽  
Tilting Pad ◽  
Edge Distribution

This paper compares three different lubricant supply methods—pressurized supply (flooded), spray feed, and leading edge distribution groove—and analyzes their influence on the performance of tilting pad, equalizing thrust bearings. The paper presents experimental data on 267 mm (10-1/2 in.) o.d. bearings, operating at shaft speeds up to 13,000 rpm with loads ranging up to 3.45 MPa (500 psi). The data presented demonstrate the effect each lubricant supply method has on bearing power loss and temperature. Conclusions are drawn, based upon the effectiveness of each design, to guide the potential user.

Effects of High-Operating Speeds on Tilting Pad Thrust Bearing Performance

1976 ◽  
Vol 98 (1) ◽  
pp. 73-79 ◽  
Author(s):  
J. W. Capitao ◽  
R. S. Gregory ◽  
R. P. Whitford
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Power Loss ◽  
High Speed ◽  
Thrust Bearing ◽  
Full Scale ◽  
Thrust Bearings ◽  
Tilting Pad ◽  
Speed Performance ◽  
Bearing Loads

A comparison of the high-speed performance characteristics of tilting-pad, self-equalizing type thrust bearings through two independent full-scale programs is reported. This paper presents experimental data on centrally pivoted, 6-pad, 267-mm (10 1/2-in.) and 304-mm (12-in.) O.D. bearings operating at shaft speeds up to 14000 rpm and bearing loads ranging up to 2.76 MPa (400 psi). Data presented demonstrate the effects of speed and loading on bearing power loss and metal temperatures. Included is a discussion of optimum oil supply flow rate based upon considerations of bearing pad temperatures and power loss values.

Further Test Results of the Leading-Edge-Groove (LEG) Tilting Pad Thrust Bearing

1988 ◽  
Vol 110 (1) ◽  
pp. 174-179 ◽  
Author(s):  
A. M. Mikula
Keyword(s):  
Experimental Data ◽  
Test Data ◽  
Power Loss ◽  
Thrust Bearing ◽  
Leading Edge ◽  
Temperature Data ◽  
Experimental Temperature ◽  
Test Results ◽  
Tilting Pad ◽  
Controlled Flow

This paper compares the LEG and pressurized controlled flow lubricant supply methods and evaluates their influence on the babbitt temperature and bearing power loss performance of a tilting pad, equalizing thrust bearing. The paper also presents new experimental temperature data from bidirectional testing of a unidirectional LEG bearing. The experimental data presented is from a 267 mm (10.5 in.) O.D. bearing, operating at shaft speeds up to 13000 rpm with applied loads that produced mean unit pressures of up to 3.45 MPa (500 psi). Conclusions are drawn based upon these test data.

Performance of Elastic, Centrally Pivoted, Sector, Thrust-Bearing Pads—Part I

1961 ◽  
Vol 83 (2) ◽  
pp. 169-178 ◽  
Author(s):  
B. Sternlicht ◽  
J. C. Reid ◽  
E. B. Arwas
Keyword(s):  
Experimental Data ◽  
Approximate Calculation ◽  
Thrust Bearing ◽  
Full Scale ◽  
Fluid Film ◽  
Thermal Gradients ◽  
Thrust Bearings ◽  
Adiabatic Conditions ◽  
Tilting Pad

This is the first of three papers on the results of a recently completed study of the performance of tilting pad thrust bearings. It describes a method of analysis that was worked out for these bearings, which includes viscosity variations in the fluid film and an approximate calculation of the pad deflections caused by the hydrodynamic pressures. Equilibrium of moments is satisfied, laminar and adiabatic conditions are assumed, and the lubricant is incompressible. The two subsequent papers of this series will describe: (a) The results of an analysis which includes a more rigorous determination of pad deflections caused by hydrodynamic pressures and thermal gradients. (b) A comparison of analytical results with experimental data obtained in full-scale bearing tests.

scholarly journals On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Michal Wasilczuk ◽  
Grzegorz Rotta
Keyword(s):  
Power Loss ◽  
Power Plants ◽  
Thrust Bearing ◽  
Fluid Film ◽  
Total Power ◽  
Thrust Bearings ◽  
Oil Supply ◽  
Water Power ◽  
Lubricant Flow ◽  
Tilting Pad

Different systems of direct oil supply have been developed in order to facilitate efficient introduction of fresh lubricant to the oil gap and reduction of churning power loss in tilting pad thrust bearings. Up to now there is no documented application of the supply groove in large thrust bearings used in water power plants. The results of modeling lubricant flow in the lubricating groove of a thrust bearing pad will be presented in the paper. CFD software was used to carry out fluid film calculations. Such analysis makes it possible to modify groove geometry and other parameters and to study their influence on bearing performance. According to the results a remarkable decrease in total power loss due to avoiding churning losses can be observed in the bearing.

The Influence of Injection Pockets on the Performance of Tilting-Pad Thrust Bearings: Part II — Comparison Between Theory and Experiment

2006 ◽  
Author(s):  
Niels Heinrichson ◽  
Axel Fuerst ◽  
Ilmar Ferreira Santos
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Three Dimensional ◽  
Leading Edge ◽  
Operating Conditions ◽  
Oil Film ◽  
Thrust Bearings ◽  
Tilting Pad ◽  
High Pressure Injection ◽  
Theoretical Pressure

This is Part II of a two-part series of papers describing the effects of high pressure injection pockets on the operating conditions of tilting-pad thrust bearings. Measurements of the distribution of pressure and oil film thickness are presented for tilting-pad thrust bearing pads of approximately 100 cm2 surface area. Two pads are measured in a laboratory test-rig at loads of approximately 0.5, 1.5 and 4.0 MPa and velocities of up to 33 m/s. One pad has a plain surface. The other pad has a conical injection pocket at the pivot point and a leading edge taper. The measurements are compared to theoretical values obtained using a three dimensional thermoelasto-hydrodynamic (TEHD) numerical model. At low and intermediate loads the theoretical pressure distribution corresponds well to the measured values for both pads although the influence of the pocket is slightly underestimated. At high loads large discrepancies exist for the pad with an injection pocket. It is argued that this is likely to be due to the unevenness of the collar surface. The measured and theoretical values of oil film thickness compare well at low loads. At high loads discrepancies grow to up to 25 %. It is argued that this is due to the accuracy of the measurements.

Influence of Turbulence on Performance Characteristics of the Tilting Pad Thrust Bearing

1974 ◽  
Vol 96 (1) ◽  
pp. 110-116 ◽  
Author(s):  
J. W. Capitao
Keyword(s):  
Turbulent Flow ◽  
Power Loss ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Equal Area ◽  
Thrust Bearings ◽  
Finite Difference Equations ◽  
Tilting Pad ◽  
Oil Flow ◽  
Flow Theories

The influence of fluid film turbulence on the performance of centrally-pivoted tilting pad thrust bearings was analyzed. Major features of the analysis are: (1) today’s two predominant “engineering” turbulent flow theories are delineated and their quantitative predictions compared; (2) a spherical pad profile was assumed, and (3) an equal area technique was used in the finite difference equations. The results confirmed earlier predictions of increases in power loss and load capacity when compared to a laminar solution. Also, no significant differences were found between the results predicted by the two predominant turbulent flow theories. Power loss, load capacity, and hydrodynamic oil flow are given for 13, 15, and 17 in. sizes. Comparisons of laminar and turbulent numerical results are presented.

Performance of Thrust Bearings at High Operating Speeds

1974 ◽  
Vol 96 (1) ◽  
pp. 7-13 ◽  
Author(s):  
R. S. Gregory
Keyword(s):  
Research Program ◽  
Feed Rate ◽  
Power Loss ◽  
Thrust Bearing ◽  
Operating Conditions ◽  
Thrust Bearings ◽  
Laminar To Turbulent Transition ◽  
Turbulent Transition ◽  
Tilting Pad ◽  
Bearing Loads

As part of a continuing research program, a standard 10 1/2 in. dia thrust bearing, of the tilting-pad, self-equalizing type, was tested at shaft speeds up to 11,000 rpm and bearing loads ranging up to 400 psi. The bearing and lube oil system were instrumented to measure bearing performance under laminar and turbulent operating conditions. The effects of varying the oil feed rate on bearing temperature and power loss are discussed in this paper. Some observations on the laminar to turbulent transition region are included.

Sign in / Sign up

Export Citation Format

Share Document