The Effects of Ambient Conditions on Gas Turbine Emissions—Generalized Correction Factors

1978 ◽  
Vol 100 (4) ◽  
pp. 640-646 ◽  
Author(s):  
P. Donovan ◽  
T. Cackette
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Correction Factors ◽  
Oxides Of Nitrogen ◽  
Ambient Conditions ◽  
Nitrogen Emission ◽  
Wide Range

A set of factors which reduces the variability due to ambient conditions of the hydrocarbon, carbon monoxide, and oxides of nitrogen emission indices has been developed. These factors can be used to correct an emission index to reference day ambient conditions. The correction factors, which vary with engine rated pressure ratio for NOx and idle pressure ratio for HC and CO, can be applied to a wide range of current technology gas turbine engines. The factors are a function of only the combustor inlet temperature and ambient humidity.

Thermo-Economic Optimization in the Design of Small-Scale and Residential Cogeneration Systems

2009 ◽  
Author(s):  
C. P. Lea˜o ◽  
S. F. C. F. Teixeira ◽  
A. M. Silva ◽  
M. L. Nunes ◽  
L. A. S. B. Martins
Keyword(s):  
Gas Turbine ◽  
Urban Areas ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Turbine Engines ◽  
Small Scale ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Economic Optimization ◽  
Micro Turbine

In recent years, gas-turbine engines have undergone major improvements both in efficiency and cost reductions. Several inexpensive models are available in the range of 30 to 250 kWe, with electrical efficiencies already approaching 30%, due to the use of a basic air-compressor associated to an internal air pre-heater. Gas-turbine engines offer significant advantages over Diesel or IC engines, particularly when Natural Gas (NG) is used as fuel. With the current market trends toward Distributed Generation (DG) and the increased substitution of boilers by NG-fuelled cogeneration installations for CO2 emissions reduction, small-scale gas turbine units can be the ideal solution for energy systems located in urban areas. A numerical optimization method was applied to a small-scale unit delivering 100 kW of power and 0.86 kg/s of water, heated from 318 to 353K. In this academic study, the unit is based on a micro gas-turbine and includes an internal pre-heater, typical of these low pressure-ratio turbines, and an external heat recovery system. The problem was formulated as a non-linear optimisation model with the minimisation of costs subject to the physical and thermodynamic constraints. Despite difficulties in obtaining data for some of the components cost-equations, the preliminary results indicate that the optimal compressor pressure ratio is about half of the usual values found in large installations, but higher than those of the currently available micro-turbine models, while the turbine inlet temperature remains virtually unchanged.

Advanced Multi-Cup Fuel Injector Technology for Environmentally Responsible Aviation Gas Turbine Engines

2015 ◽  
Author(s):  
Erlendur Steinthorsson ◽  
Adel Mansour ◽  
Brian Hollon ◽  
Michael Teter ◽  
Clarence Chang
Keyword(s):  
Gas Turbine ◽  
Direct Injection ◽  
Pressure Ratio ◽  
Test Facility ◽  
Turbine Engines ◽  
Practical Implementation ◽  
Gas Turbine Engines ◽  
Fuel Injector ◽  
Ambient Conditions ◽  
Environmentally Responsible

Participating in NASA’s Environmentally Responsible Aviation (ERA) Project, Parker Hannifin built and tested multipoint Lean Direct Injection (LDI) fuel injectors designed for NASA’s N+2 55:1 Overall Pressure-Ratio (OPR) gas turbine engine cycles. The injectors are based on Parker’s earlier three-zone injector (3ZI) which was conceived to enable practical implementation of multipoint LDI schemes in conventional aviation gas turbine engines. The new injectors offer significant aerodynamic design flexibility, excellent thermal performance, and scalability to various engine sizes. The injectors built for this project contain 15 injection points and incorporate staging to enable operation at low power conditions. Ignition and flame stability were demonstrated at ambient conditions with ignition air pressure drop as low as 0.3% and fuel-to-air ratio (FAR) as low as 0.011. Lean Blowout (LBO) occurred at FAR as low as 0.005 with air at 460 K and atmospheric pressure. A high pressure combustion testing campaign was conducted in the CE-5 test facility at NASA Glenn Research Center at pressures up to 250 psi and combustor exit temperatures up to 2,033 K (3,200 °F). The tests demonstrated estimated LTO cycle emissions that are about 30% of CAEP/6 for a reference 60,000 lbf thrust, 54.8-OPR engine. This paper presents some details of the injector design along with results from ignition, LBO and emissions testing.

scholarly journals ВПЛИВ ГУСТОТИ РЕШІТКИ НА АЕРОДИНАМІЧНУ НАВАНТАЖЕНІСТЬ РОБОЧОГО КОЛЕСА ОСЬОВОГО ВЕНТИЛЯТОРА

2020 ◽  
pp. 38-43
Author(s):  
Екатерина Викторовна Дорошенко ◽  
Михаил Владимирович Хижняк ◽  
Юрий Матвеевич Терещенко
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Average Radius ◽  
Gas Turbine Engines ◽  
Axial Fan ◽  
Aerodynamic Loading ◽  
Wide Range ◽  
Axial Fans ◽  
Bypass Ratio

The main requirements that apply to axial fans and axial compressors of aircraft gas turbine engines include minimum dimensions and weight; high aerodynamic load; high coefficient of performance; wide range of steady work; high reliability. For gas turbine engines, the requirements of minimum weight and dimensions are especially important, since the engines must provide flights at high velocities and altitudes. This study aims to assess the effect of the solidity of the impeller fan on the average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The object of the study is the impeller of the fan. The solidity of the impeller fan on the average radius varied in the range from 1.8 to 0.82, the number of blades of the impeller fan varied from 33 to 15, respectively. The studies in this work were carried out by the method of numerical experiment. The flow in the axial fans was simulated by solving the system of Navier-Stokes equations, which were closed by the SST turbulent viscosity model. Based on the analysis of the results of the study, an assessment is made of the influence of the solidity of the impeller fan at an average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The research results showed that with a decrease in the solidity of the impeller fan at an average radius of 1.8 to 0.82 in operating modes with an axial inlet velocity of 80 to 120 m / s, the impeller fan pressure ratio decreases by 0.11 ... 3.2 %. The maximum decrease in the fan pressure ratio increase for the fan impeller with the parameters studied is 3.2 %, with a decrease in the number of fan blades from 33 to 15, while the total weight of the blades decreases by 54.55 %. The decrease in the solidity on the average radius of the impeller of the studied fan leads to a decrease in the relative sizes of the low-velocity zones at the sleeve and on the periphery and to a decrease in the level of flow unevenness. A further reduction in the level of flow non-uniformity behind the fan is possible when using the boundary layer control in the fan - this is the task of subsequent studies.

scholarly journals МЕТОД РАСЧЕТА ТЕРМОГАЗОДИНАМИЧЕСКИХ ПАРАМЕТРОВ ТУРБОВАЛЬНОГО ГТД НА ОСНОВЕ ПОВЕНЦОВОГО ОПИСАНИЯ ЛОПАТОЧНЫХ МАШИН. ЧАСТЬ 1. ОСНОВНЫЕ УРАВНЕНИЯ

2018 ◽  
pp. 48-58
Author(s):  
Людмила Георгиевна Бойко ◽  
Олег Владимирович Кислов ◽  
Наталия Владимировна Пижанкова
Keyword(s):  
Gas Turbine ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Geometrical Parameters ◽  
Gas Turbine Engines ◽  
Balance Equations ◽  
Wide Range ◽  
In Series ◽  
Multistage Compressor

Gas turbine engines processes mathematic simulations are widely used in different steps of its living cycle. All engine simulations may be divided into different difficulty levels: higher simulation level allows doing a more pre­cise description of physical processes in main units of gas turbine engines and their elements. It gives the oppor­tunity for getting better arrangement of calculation results and experimental data, reduce the quality of factors, which are traditionally used in determine engine operational characteristics with 1-level models.The purpose of the article is to describe the thermogasdynamic parameters and maintenance perfomances cal­culation method, which based on second level mathematic simulation. Its main feature is blade-to-blade turbomachines description (multistage compressor and multistage cooling gas turbine), which allows to take into account blade and flow path geometrical parameters. Their changing during the gas turbine engine design and de­velopment processes influence its performances: thrust, fuel consumption, efficiency as functions of values of flow rate, rotational speed, engine entrance conditions and so on. All these dependences could be defined by using proposed calculation method.In distinction from methods which are noted, this method allows to concede compressor or turbine incidence angles, drag values, pressure ratio, surge margin in design and off-design  engine regimes. The opportunity to take into account by-passing and air bleeding from compressor blade channels and their engine parameters influence is very important also.The article includes calculation method main points, block-scheme, equations system, which gives the opportunity of alignment the engine units and their elements in wide range of state working regimes. Set of equations consists of flow rate balance equations through the stages of multistage compressor and turbine, combustion chamber and connected channels. Also system includes power balance equations, by-passing, air bleeding from compressor stages channels, its admission into the cooling turbine stages and ac­counts their thermodynamic parameters. Compressors and turbines maps parameters are calculated with main turbomachinery theory lows and semi-empirical dependences.This article is the first in series of articles, which considers this problem

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

Thermodynamic Performance of Complex Gas Turbine Cycles

2002 ◽  
Author(s):  
Sanjay ◽  
Onkar Singh ◽  
B. N. Prasad
Keyword(s):  
Gas Turbine ◽  
Specific Power ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Air Cooling ◽  
Gas Turbine Engines ◽  
Current State ◽  
Thermodynamic Performance ◽  
Internal Convection ◽  
Plant Efficiency

This paper deals with the thermodynamic performance of complex gas turbine cycles involving inter-cooling, re-heating and regeneration. The performance has been evaluated based on the mathematical modeling of various elements of gas turbine for the real situation. The fuel selected happens to be natural gas and the internal convection / film / transpiration air cooling of turbine bladings have been assumed. The analysis has been applied to the current state-of-the-art gas turbine technology and cycle parameters in four classes: Large industrial, Medium industrial, Aero-derivative and Small industrial. The results conform with the performance of actual gas turbine engines. It has been observed that the plant efficiency is higher at lower inter-cooling (surface), reheating and regeneration yields much higher efficiency and specific power as compared to simple cycle. There exists an optimum overall compression ratio and turbine inlet temperature in all types of complex configuration. The advanced turbine blade materials and coating withstand high blade temperature, yields higher efficiency as compared to lower blade temperature materials.

Practical Implications of Integrating Turbomachinery Into the Air Turborocket

2004 ◽  
Author(s):  
Joshua A. Clough ◽  
Mark J. Lewis
Keyword(s):  
Gas Turbine ◽  
Aircraft Engine ◽  
Launch Vehicle ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Space Launch ◽  
Practical Implications

The development of new reusable space launch vehicle concepts has lead to the need for more advanced engine cycles. Many two-stage vehicle concepts rely on advanced gas turbine engines that can propel the first stage of the launch vehicle from a runway up to Mach 5 or faster. One prospective engine for these vehicles is the Air Turborocket (ATR). The ATR is an innovative aircraft engine flowpath that is intended to extend the operating range of a conventional gas turbine engine. This is done by moving the turbine out of the core engine flow, alleviating the traditional limit on the turbine inlet temperature. This paper presents the analysis of an ATR engine for a reusable space launch vehicle and some of the practical problems that will be encountered in the development of this engine.

scholarly journals Cooled Radial In-Flow Turbines for Advanced Gas Turbine Engines

1981 ◽  
Author(s):  
J. M. Lane
Keyword(s):  
Gas Turbine ◽  
High Performance ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Gas Turbine Engines ◽  
Radial Turbine ◽  
Internally Cooled ◽  
Subsequent Discussion ◽  
Near Term

While the radial in-flow turbine has consistently demonstrated its capability as a high-performance component for small gas turbine engines, its use has been relegated to lower turbine-inlet-temperature cycles due to insurmountable problems with respect to the manufacturing of radial turbine rotors with internal cooling passages. These cycle temperature limitations are not consistent with modern trends toward higher-performance, fuel-conservative engines. This paper presents the results of several Army-sponsored programs, the first of which addresses the performance potential for the high-temperature radial turbine. The subsequent discussion presents the results of two successful programs dedicated to developing fabrication techniques for internally cooled radial turbines, including mechanical integrity testing. Finally, future near-term capabilities are projected.

scholarly journals Development of 300 kW Class Ceramic Gas Turbine (CGT302)

1995 ◽  
Author(s):  
Kozi Nishio ◽  
Junzo Fujioka ◽  
Tetsuo Tatsumi ◽  
Isashi Takehara
Keyword(s):  
Gas Turbine ◽  
Development Program ◽  
Pollutant Emissions ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Turbine Inlet Temperature ◽  
Iso Standard ◽  
Current State ◽  
Ceramic Components

With the aim of achieving higher efficiency, lower pollutant emissions, and multi-fuel capability for small to medium-sized gas turbine engines for use in co-generation systems, a ceramic gas turbine (CGT) research and development program is being promoted by the Japanese Ministry of International Trade and Industry (MITI) as a part of its “New Sunshine Project”. Kawasaki Heavy Industries (KHI) is participating in this program and developing a regenerative two-shaft CGT (CGT302). In 1993, KHI conducted the first test run of an engine with full ceramic components. At present, the CGT302 achieves 28.8% thermal efficiency at a turbine inlet temperature (TIT) of 1117°C under ISO standard conditions and an actual TIT of 1250°C has been confirmed at the rated speed of the basic CGT. This paper consists of the current state of development of the CGT302 and how ceramic components are applied.

Sign in / Sign up

Export Citation Format

Share Document