Application of Unsteady Computational Fluid Dynamics Methods to Trailing Edge Cutback Film Cooling

2014 ◽  
Vol 136 (12) ◽  
Author(s):  
Silvia Ravelli ◽  
Giovanna Barigozzi
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Image Velocimetry ◽  
Unsteady Rans ◽  
Exit Mach Number ◽  
Nozzle Guide

The main purpose of this numerical investigation is to overcome the limitations of the steady modeling in predicting the cooling efficiency over the cutback surface in a high pressure turbine nozzle guide vane. Since discrepancy between Reynolds-averaged Navier–Stokes (RANS) predictions and measured thermal coverage at the trailing edge was attributable to unsteadiness, Unsteady RANS (URANS) modeling was implemented to evaluate improvements in simulating the mixing between the mainstream and the coolant exiting the cutback slot. With the aim of reducing the computation effort, only a portion of the airfoil along the span was simulated at an exit Mach number of Ma2is = 0.2. Three values of the coolant-to-mainstream mass flow ratio were considered: MFR = 0.66%, 1.05%, and 1.44%. Nevertheless the inherent vortex shedding from the cutback lip was somehow captured by the URANS method, the computed mixing was not enough to reproduce the measured drop in adiabatic effectiveness η along the streamwise direction, over the cutback surface. So modeling was taken a step further by using the scale adaptive simulation (SAS) method at MFR = 1.05%. Results from the SAS approach were found to have potential to mimic the experimental measurements. Vortices shedding from the cutback lip were well predicted in shape and magnitude, but with a lower frequency, as compared to particle image velocimetry (PIV) data and flow visualizations. Moreover, the simulated reduction in film cooling effectiveness toward the trailing edge was similar to that observed experimentally.

Application of Unsteady CFD Methods to Trailing Edge Cutback Film Cooling

2014 ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Unsteady Rans ◽  
Exit Mach Number ◽  
Nozzle Guide

The main purpose of this numerical investigation is to overcome the limitations of the steady modeling in predicting the cooling efficiency over the cutback surface in a high pressure turbine nozzle guide vane. Since discrepancy between Reynolds-averaged Navier–Stokes (RANS) predictions and measured thermal coverage at the trailing edge was attributable to unsteadiness, Unsteady RANS (URANS) modeling was implemented to evaluate improvements in simulating the mixing between the mainstream and the coolant exiting the cutback slot. With the aim of reducing the computation effort, only a portion of the airfoil along the span was simulated at an exit Mach number of Ma2is = 0.2. Three values of the coolant-to-mainstream mass flow ratio were considered: MFR = 0.66%, 1.05%, and 1.44%. Nevertheless the inherent vortex shedding from the cutback lip was somehow captured by the URANS method, the computed mixing was not enough to reproduce the measured drop in adiabatic effectiveness η along the streamwise direction, over the cutback surface. So modeling was taken a step further by using the Scale Adaptive Simulation (SAS) method at MFR = 1.05%. Results from the SAS approach were found to have potential to mimic the experimental measurements. Vortices shedding from the cutback lip were well predicted in shape and magnitude, but with a lower frequency, as compared to PIV data and flow visualizations. Moreover, the simulated reduction in film cooling effectiveness toward the trailing edge was similar to that observed experimentally.

Pressure Side and Cutback Trailing Edge Film Cooling in a Linear Nozzle Vane Cascade at Different Mach Numbers

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Giovanna Barigozzi ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Momentum Boundary Layer

Tests on a specifically designed linear nozzle guide vane cascade with trailing edge coolant ejection were carried out to investigate the influence of trailing edge bleeding on both aerodynamic and thermal performance. The cascade is composed of six vanes with a profile typical of a high pressure turbine stage. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is ejected not only through the slots but also through two rows of cooling holes placed on the pressure side, upstream of the cutback. The cascade was tested for different isentropic exit Mach numbers, ranging from M2is = 0.2 to M2is = 0.6, while varying the coolant to mainstream mass flow ratio MFR up to 2.8%. The momentum boundary layer behavior at a location close to the trailing edge, on the pressure side, was assessed by means of laser Doppler measurements. Cases with and without coolant ejection allowed us to identify the contribution of the coolant to the off the wall velocity profile. Thermochromic liquid crystals (TLC) were used to map the adiabatic film cooling effectiveness on the pressure side cooled region. As expected, the cutback effect on cooling effectiveness, compared to the other cooling rows, was dominant.

The Effect of Step Misalignment on Purge Flow Cooling of Nozzle Guide Vane at Transonic Conditions

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Luke Luehr ◽  
Ridge Sibold ◽  
Shuo Mao ◽  
Wing F. Ng ◽  
Zhigang Li ◽  
...  
Keyword(s):  
Nusselt Number ◽  
Film Cooling ◽  
Guide Vane ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Exit Mach Number ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Abstract This study describes a detailed investigation on the effects that upstream step misalignment and upstream purge film cooling have on the endwall heat transfer for first stage nozzle guide vanes (NGVs) in a gas turbine at transonic conditions. Endwall Nusselt number and adiabatic film-cooling effectiveness distributions were experimentally measured and compared with flow visualization. Tests were conducted in a transonic linear cascade blowdown facility at an inlet freestream turbulence intensity of 16%, an exit Mach number of 0.85, and an exit Re = 1.5 × 106 based on axial chord. Varied upstream purge blowing ratios (BRs) and a no-blowing case were tested for three different upstream step geometries, the baseline (no misalignment), a span-wise upstream step of +4.86% span, and a step of −4.86% span. Experimentation shows that compared with no-blowing case, the addition of upstream purge film cooling increases the Nusselt number at injection upward of 50% but lowers it in the passage throat by approximately 20%. The backward facing step induces more turbulent mixing between the coolant and mainstream flows, thus reducing film effectiveness coverage and increasing Nusselt number by nearly 40% in the passage throat. In contrast, the presence of a forward step creates a more stable boundary layer for the coolant flow aiding to help keep the film attached to the endwall. Increasing the blowing ratio increases film-cooling effectiveness and endwall coverage up to a certain point, beyond which, the high momentum of the coolant results in poor cooling performance due to jet liftoff.

The Effect of Step Misalignment on Purge Flow Cooling of Nozzle Guide Vane at Transonic Conditions

2019 ◽  
Author(s):  
Luke Luehr ◽  
Ridge Sibold ◽  
Shuo Mao ◽  
Wing F. Ng ◽  
Zhigang Li ◽  
...  
Keyword(s):  
Nusselt Number ◽  
Film Cooling ◽  
Guide Vane ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Exit Mach Number ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Abstract This study describes a detailed investigation on the effects that step misalignment and upstream purge film cooling have on the endwall heat transfer for 1st stage nozzle guide vanes in a land-based power generating gas turbine at transonic conditions. Endwall Nusselt number and adiabatic film cooling effectiveness distributions were experimentally measured and compared with flow visualization. Tests were conducted in a transonic linear cascade blowdown facility where data were gathered at an exit Mach number of 0.85 with a freestream turbulence intensity of 16% at an exit Re = 1.5 × 106 based on axial chord. Varied upstream purge blowing ratios and a no blowing case were tested for 3 different upstream step geometries, the baseline (no misalignment), a span-wise upstream step of +4.86% span, and a step of −4.86% span. Experimentation shows that the addition of upstream purge film cooling increases the Nusselt number at injection upwards of 50% but lowers it in the throat of the passage by approximately 20% compared to no blowing case. The addition of a backward facing step induces more turbulent mixing between the coolant and mainstream flows, thus reducing film effectiveness coverage and increasing Nusselt number by nearly 40% in the passage throat. In contrast, the presence of a forward step creates a more stable boundary layer for the coolant flow aiding to help keep the film attached to the endwall at higher blowing ratios. Increasing the blowing ratio increases film cooling effectiveness and endwall coverage up to a certain point, beyond which, the high momentum of the coolant results in poor cooling performance due to jet liftoff.

Pressure Side and Cutback Trailing Edge Film Cooling in a Linear Nozzle Vane Cascade at Different Mach Numbers

2011 ◽  
Author(s):  
Giovanna Barigozzi ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Momentum Boundary Layer

Tests on a specific designed linear nozzle guide vane cascade with trailing edge coolant ejection were carried out to investigate the influence of trailing edge bleeding on both aerodynamic and thermal performance. The cascade is composed of six vanes with a profile typical of a high pressure turbine stage. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is ejected not only through the slots but also through two rows of cooling holes placed on the pressure side, upstream of the cutback. The cascade was tested for different isentropic exit Mach numbers, ranging from M2is = 0.2 to M2is = 0.6, while varying the coolant to mainstream mass flow ratio MFR up to 2.8%. The momentum boundary layer behavior at a location close to the trailing edge, on the pressure side, was assessed by means of Laser Doppler measurements. Cases with and without coolant ejection allowed to identify the contribution of the coolant to the off the wall velocity profile. Thermochromic Liquid Crystals (TLC) were used to map adiabatic film cooling effectiveness on the pressure side cooled region. As expected, the cutback effect on cooling effectiveness, compared to the other cooling rows, was dominant.

Overall Cooling Effectiveness Measurements on Pressure Side Surface of the Nozzle Guide Vane With Optimized Film Cooling Hole Arrangements

2017 ◽  
Author(s):  
Dong-Ho Rhee ◽  
Young Seok Kang ◽  
Bong Jun Cha ◽  
Sanga Lee
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Side Surface ◽  
Internal Cooling ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Rib Turbulators ◽  
Nozzle Guide

Most of the optimization researches on film cooling have dealt with adiabatic film cooling effectiveness on the surface. However, the information on the overall cooling effectiveness is required to estimate exact performance of the optimization configuration since hot components such as nozzle guide vane have not only film cooling but also internal cooling features such as rib turbulators, jet impingement and pin-fins on the inner surface. Our previous studies [1,2] conducted the hole arrangement optimization to improve adiabatic film cooling effectiveness values and uniformity on the pressure side surface of the nozzle guide vane. In this study, the overall cooling effectiveness values were obtained at various cooling mass flow rates experimentally for the baseline and the optimized hole arrangements proposed by the previous study [1] and compared with the adiabatic film cooling effectiveness results. The tests were conducted at mainstream exit Reynolds number based on the chord of 2.2 × 106 and the coolant mass flow rate from 5 to 10% of the mainstream. For the experimental measurements, a set of tests were conducted using an annular sector transonic turbine cascade test facility in Korea Aerospace Research Institute. To obtain the overall cooling effectiveness values on the pressure side surface, the additive manufactured nozzle guide vane made of polymer material and Inconel 718 were installed and the surface temperature was measured using a FLIR infrared camera system. Since the optimization was based on the adiabatic film cooling effectiveness, the regions with rib turbulators and film cooling holes show locally higher overall cooling effectiveness due to internal convection and conduction, which can cause non-uniform temperature distributions. Therefore, the optimization of film cooling configuration should consider the effect of the internal cooling to avoid undesirable non-uniform cooling.

Investigation on the Effect of Different Lands on Trailing Edge Slot Film Cooling

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
Yang Xu ◽  
Hui-ren Zhu ◽  
Wei-jiang Xu ◽  
Jian-sheng Wei
Keyword(s):  
Nusselt Number ◽  
Film Cooling ◽  
Turbine Blades ◽  
Experimental Studies ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Wall Functions ◽  
Film Cooling Effectiveness ◽  
Slot Film Cooling

Abstract Trailing edge slot film cooling is a widely used method for protecting the trailing edge of turbine blades from hot gas impingement. The structures that separate the slots, known as “lands,” come in a variety of configurations. This paper presents the effects of the trailing edge with different lands on the film cooling performance. Experimental studies are conducted on the film cooling effectiveness and Nusselt number with different lands. Four trailing edge configurations, including the straight lands, the beveling lands, the fillet lands and the tapered lands are considered under four blowing ratios (0.5, 0.7, 1.0 and 1.5). The Reynolds numbers of mainstream is fixed as 375,000. Film cooling effectiveness and Nusselt number performances are measured by transient liquid crystal measurement technique. Reynolds-averaged Navier-Stokes (RANS) simulation with realizable k-ε turbulence model and enhanced wall functions are performed using a commercial code Fluent. In each case, the slot height is kept constant. It is shown that the beveling lands, the fillet lands and the tapered lands have higher cooling effectiveness and lower Nusselt number compared with the straight lands. Under higher blowing ratios, the trailing edges of all four lands have higher cooling effectiveness and higher Nusselt number.

Comparison of Film Cooling Performance for Different Purge Slot Configurations in a Cylindrical and State-of-the-Art Nozzle Guide Vane

2021 ◽  
Author(s):  
Christian Landfester ◽  
Gunther Müller ◽  
Robert Krewinkel ◽  
Clemens Domnick ◽  
Martin Böhle
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on the film cooling performance by injecting coolant through the purge slot. An experimental study compares the film cooling effectiveness as well as the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with four cylindrical vanes, the contoured endwall cascade consisted of four modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the purge slot width and injection angle, as well as different blowing ratios (BR) at an engine-like density ratio (DR = 1.6) were realized to investigate the real-life effect of thermal expansion, design modifications and the interaction between secondary flow and coolant. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. The Pressure Sensitive Paint (PSP) technique was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements (DR = 1.0) were performed to measure the flow field with its characteristic vortex structures as well as the loss distribution in the vane wake region. For a more profound insight into the origin and development of the secondary flows, oil dye visualizations were carried out on both endwalls. The measurement results will be discussed based on a side-by-side comparison of the distribution of film cooling effectiveness on the endwall, its area-averaged values as well as the two-dimensional distribution of total pressure losses and the secondary flow field. The results of this study show that the advances in NGV design development have had a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. In contrast to the results of the cylindrical profile, sufficient cooling can be already provided with a perpendicular injection in the case of the modern NGV. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Experimental Investigation of Turbine Phantom Cooling on Endwall With Trailing Edge Discharge Flow

2014 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Scale Up ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Discharge Flow ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Compound Angle

The film cooling ejection on High Pressure (Hp) turbine component surface is strongly affected by the complex flow structure in the nozzle guide vane or rotor blade passages. The action of secondary flow in the main passage could dominate the film cooling effectiveness distribution on the component surfaces. The film cooling ejections from endwall and airfoil trailing edge are mixed by the secondary flow. Considering a small part of the coolant ejection from trailing edge discharge flow will move from the airfoil trailing edge pressure side to endwall downstream and then cover some area, the interaction between the coolants injected from endwall and airfoil trailing edge is worth investigating. Though the temperature of coolant discharge flow from trailing edge increases after the mixing process in the internal cooling procedure, the ejections moving from airfoil to endwall still have the potential of second order cooling. This part of the coolant is called “Phantom cooling flow” in the paper. A typical scale-up model of Hp turbine NGV is used in the experiment to investigate the cooling performance of ejection from trailing edge. Instead of the airfoil trailing edge platform itself, the film cooling effectiveness is measured on the downstream part of the endwall. This paper is focused on the trailing edge discharge flow with compound angle effects and the coolant from discharge holes moving from trailing edge to endwall surface. The coolant flow is injected from the straight discharge holes with a compound angle of 15deg and 45deg respectively. The film cooling holes on the endwall are used simultaneously to investigate the combined effects. The blowing ratio and different configurations of compound angle holes are selected to be the changing parameters in the paper. The experiment is completed with the blowing ratio changing from M = 0.7 to M = 1.3 and the compound angle is introduced to the entire row of trailing edge discharge holes (full span), with inlet Reynolds numbers of Re = 3.5×105 and an inlet Mach number of Ma = 0.1.

Shower Head and Trailing Edge Cooling Influence on Transonic Vane Aero Performance

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten H. Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Trailing Edge ◽  
Aerodynamic Loss ◽  
Nozzle Guide Vane ◽  
Turbine Vane ◽  
Engine Component ◽  
Annular Sector ◽  
Exit Mach Number ◽  
Nozzle Guide

An experimental investigation on a cooled nozzle guide vane (NGV) has been conducted in an annular sector to quantify aerodynamic influences of shower head (SH) and trailing edge (TE) cooling. The investigated vane is a typical high pressure gas turbine vane, geometrically similar to a real engine component, operated at a reference exit Mach number of 0.89. The investigations have been performed for various coolant-to-mainstream mass–flux ratios. New loss equations are derived and implemented regarding coolant aerodynamic losses. Results lead to a conclusion that both TE cooling and SH film cooling increase the aerodynamic loss compared to an uncooled case. In addition, the TE cooling has higher aerodynamic loss compared to the SH cooling. Secondary losses decrease with inserting SH film cooling compared to the uncooled case. The TE cooling appears to have less impact on the secondary loss compared to the SH cooling. Area-averaged exit flow angles around midspan increase for the TE cooling.

Sign in / Sign up

Export Citation Format

Share Document