Measurements and Modeling of Ingress in a New 1.5-Stage Turbine Research Facility

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Marios Patinios ◽  
James A. Scobie ◽  
Carl M. Sangan ◽  
J. Michael Owen ◽  
Gary D. Lock
Keyword(s):  
Theoretical Model ◽  
Gas Turbines ◽  
Test Facility ◽  
Radial Clearance ◽  
Operating Life ◽  
The Core ◽  
Wide Range ◽  
Purge Flow ◽  
Rotor Disk ◽  
Engine Components

In gas turbines, hot mainstream flow can be ingested into the wheel-space formed between stator and rotor disks as a result of the circumferential pressure asymmetry in the annulus; this ingress can significantly affect the operating life, performance, and integrity of highly stressed, vulnerable engine components. Rim seals, fitted at the periphery of the disks, are used to minimize ingress and therefore reduce the amount of purge flow required to seal the wheel-space and cool the disks. This paper presents experimental results from a new 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disk. The fluid-dynamically scaled rig operates at incompressible flow conditions, far removed from the harsh environment of the engine which is not conducive to experimental measurements. The test facility features interchangeable rim-seal components, offering significant flexibility and expediency in terms of data collection over a wide range of sealing flow rates. The rig was specifically designed to enable an efficient method of ranking and quantifying the performance of generic and engine-specific seal geometries. The radial variation of CO2 gas concentration, pressure, and swirl is measured to explore, for the first time, the flow structure in both the upstream and downstream wheel-spaces. The measurements show that the concentration in the core is equal to that on the stator walls and that both distributions are virtually invariant with radius. These measurements confirm that mixing between ingress and egress is essentially complete immediately after the ingested fluid enters the wheel-space and that the fluid from the boundary layer on the stator is the source of that in the core. The swirl in the core is shown to determine the radial distribution of pressure in the wheel-space. The performance of a double radial-clearance seal is evaluated in terms of the variation of effectiveness with sealing flow rate for both the upstream and the downstream wheel-spaces and is found to be independent of rotational Reynolds number. A simple theoretical orifice model was fitted to the experimental data showing good agreement between theory and experiment for all cases. This observation is of great significance as it demonstrates that the theoretical model can accurately predict ingress even when it is driven by the complex unsteady pressure field in the annulus upstream and downstream of the rotor. The combination of the theoretical model and the new test rig with its flexibility and capability for detailed measurements provides a powerful tool for the engine rim-seal designer.

Measurements and Modelling of Ingress in a New 1.5-Stage Turbine Research Facility

2016 ◽  
Author(s):  
Marios Patinios ◽  
James A. Scobie ◽  
Carl M. Sangan ◽  
J. Michael Owen ◽  
Gary D. Lock
Keyword(s):  
Theoretical Model ◽  
Gas Turbines ◽  
Test Facility ◽  
Radial Clearance ◽  
Operating Life ◽  
The Core ◽  
Wide Range ◽  
Purge Flow ◽  
Engine Components ◽  
First Time

In gas turbines, hot mainstream flow can be ingested into the wheel-space formed between stator and rotor discs as a result of the circumferential pressure asymmetry in the annulus; this ingress can significantly affect the operating life, performance and integrity of highly-stressed, vulnerable engine components. Rim seals, fitted at the periphery of the discs, are used to minimise ingress and therefore reduce the amount of purge flow required to seal the wheel-space and cool the discs. This paper presents experimental results from a new 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disc. The fluid-dynamically-scaled rig operates at incompressible flow conditions, far removed from the harsh environment of the engine which is not conducive to experimental measurements. The test facility features interchangeable rim-seal components, offering significant flexibility and expediency in terms of data collection over a wide range of sealing-flow rates. The rig was specifically designed to enable an efficient method of ranking and quantifying the performance of generic and engine-specific seal geometries. The radial variation of CO2 gas concentration, pressure and swirl is measured to explore, for the first time, the flow structure in both the upstream and downstream wheel-spaces. The measurements show that the concentration in the core is equal to that on the stator walls and that both distributions are virtually invariant with radius. These measurements confirm that mixing between ingress and egress is essentially complete immediately after the ingested fluid enters the wheel-space and that the fluid from the boundary-layer on the stator is the source of that in the core. The swirl in the core is shown to determine the radial distribution of pressure in the wheel-space. The performance of a double radial-clearance seal is evaluated in terms of the variation of effectiveness with sealing flow rate for both the upstream and the downstream wheel-spaces and is found to be independent of rotational Reynolds number. A simple theoretical orifice model was fitted to the experimental data showing good agreement between theory and experiment for all cases. This observation is of great significance as it demonstrates that the theoretical model can accurately predict ingress even when it is driven by the complex unsteady pressure field in the annulus upstream and downstream of the rotor. The combination of the theoretical model and the new test rig with its flexibility and capability for detailed measurements provides a powerful tool for the engine rim-seal designer.

Re-Ingestion of Upstream Egress in a 1.5-Stage Gas Turbine Rig

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
James A. Scobie ◽  
Fabian P. Hualca ◽  
Marios Patinios ◽  
Carl M. Sangan ◽  
J. Michael Owen ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Co2 Concentration ◽  
Test Facility ◽  
Operating Life ◽  
Annulus Flow ◽  
Purge Flow ◽  
Rotor Disk ◽  
First Time ◽  
Measured Mass ◽  
Insight Into

In gas turbines, rim seals are fitted at the periphery of stator and rotor discs to minimize the purge flow required to seal the wheel-space between the discs. Ingestion (or ingress) of hot mainstream gases through rim seals is a threat to the operating life and integrity of highly stressed components, particularly in the first-stage turbine. Egress of sealing flow from the first-stage can be re-ingested in downstream stages. This paper presents experimental results using a 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disk. Re-ingestion was quantified using measurements of CO2 concentration, with seeding injected into the upstream and downstream sealing flows. Here, a theoretical mixing model has been developed from first principles and validated by the experimental measurements. For the first time, a method to quantify the mass fraction of the fluid carried over from upstream egress into downstream ingress has been presented and measured; it was shown that this fraction increased as the downstream sealing flow rate increased. The upstream purge was shown to not significantly disturb the fluid dynamics but only partially mixes with the annulus flow near the downstream seal, with the ingested fluid emanating from the boundary layer on the blade platform. From the analogy between heat and mass transfer, the measured mass-concentration flux is equivalent to an enthalpy flux, and this re-ingestion could significantly reduce the adverse effect of ingress in the downstream wheel-space. Radial traverses using a concentration probe in and around the rim seal clearances provide insight into the complex interaction between the egress, ingress and mainstream flows.

Re-Ingestion of Upstream Egress in a 1.5-Stage Gas Turbine Rig

2017 ◽  
Author(s):  
James A. Scobie ◽  
Fabian P. Hualca ◽  
Marios Patinios ◽  
Carl M. Sangan ◽  
J. Michael Owen ◽  
...  
Keyword(s):  
First Principles ◽  
Gas Turbines ◽  
Co2 Concentration ◽  
Test Facility ◽  
Operating Life ◽  
Annulus Flow ◽  
Purge Flow ◽  
First Time ◽  
Measured Mass ◽  
Insight Into

In gas turbines, rim seals are fitted at the periphery of stator and rotor discs to minimise the purge flow required to seal the wheel-space between the discs. Ingestion (or ingress) of hot mainstream gases through rim seals is a threat to the operating life and integrity of highly-stressed components, particularly in the first-stage turbine. Egress of sealing flow from the first-stage can be re-ingested in downstream stages. This paper presents experimental results using a 1.5-stage test facility designed to investigate ingress into the wheel-spaces upstream and downstream of a rotor disc. Re-ingestion was quantified using measurements of CO2 concentration, with seeding injected into the upstream and downstream sealing flows. Here a theoretical mixing model has been developed from first principles and validated by the experimental measurements. For the first time, a method to quantify the mass fraction of the fluid carried over from upstream egress into downstream ingress has been presented and measured; it was shown that this fraction increased as the downstream sealing flow rate increased. The upstream purge was shown to not significantly disturb the fluid dynamics but only partially mixes with the annulus flow near the downstream seal, with the ingested fluid emanating from the boundary layer on the blade platform. From the analogy between heat and mass transfer, the measured mass-concentration flux is equivalent to an enthalpy flux and this re-ingestion could significantly reduce the adverse effect of ingress in the downstream wheel-space. Radial traverses using a concentration probe in and around the rim seal clearances provide insight into the complex interaction between the egress, ingress and mainstream flows.

Influence of Flow Coefficient on Ingress Through Turbine Rim Seals

2021 ◽  
Author(s):  
Dimitrios Graikos ◽  
Mauro Carnevale ◽  
Carl M. Sangan ◽  
Gary D. Lock ◽  
James A. Scobie
Keyword(s):  
Large Scale ◽  
Rotor Blades ◽  
Flow Coefficient ◽  
Radial Clearance ◽  
Flow Conditions ◽  
Large Scale Structures ◽  
Wide Range ◽  
Purge Flow ◽  
Mass Flow Rates ◽  
Engine Components

Abstract Rim seals are critical in terms of limiting the temperature of highly-stressed engine components but function with a penalty to the power output and contribute to entropy gain stemming from mixing losses in the turbine. Ingress through rim seals is influenced by the presence of rotor blades and stator vanes, and the mainstream flow coefficient in the annulus that determines the corresponding swirl. This paper presents an experimental study of ingress upstream and downstream of the rotor disc in a 1.5-stage rig with double radial clearance rim seals. Two rotor discs were used, one with blades and one without, and two platforms were used downstream of the rotor, one with vanes and one without. Tests were conducted at two rotational speeds and a range of flow conditions was achieved by varying the annulus and sealing mass flow rates. Concentration effectiveness, swirl and steady pressure measurements separated, for the first time, the influence of the blades and vanes on ingress over a wide range of flow conditions. Measurements on the downstream stator platform provide added insight into the complex interaction between the egress and the mainstream. Measurements of unsteady pressure revealed the presence of large-scale structures, even in the absence of blades. The number and speed of the structures was shown to depend on the flow coefficient and the purge flow rate.

Influence of Flow Coefficient On Ingress Through Turbine Rim Seals

2021 ◽  
Author(s):  
Dimitrios Graikos ◽  
Mauro Carnevale ◽  
Carl Sangan ◽  
Gary Lock ◽  
James Scobie
Keyword(s):  
Large Scale ◽  
Rotor Blades ◽  
Flow Coefficient ◽  
Radial Clearance ◽  
Flow Conditions ◽  
Large Scale Structures ◽  
Wide Range ◽  
Purge Flow ◽  
Mass Flow Rates ◽  
Engine Components

Abstract Rim seals are critical in terms of limiting the temperature of highly-stressed engine components but function with a penalty to the power output and contribute to entropy gain stemming from mixing losses in the turbine. Ingress through rim seals is influenced by the presence of rotor blades and stator vanes, and the mainstream flow coefficient in the annulus that determines the corresponding swirl. This paper presents an experimental study of ingress upstream and downstream of the rotor disc in a 1.5-stage rig with double radial clearance rim seals. Two rotor discs were used, one with blades and one without, and two platforms were used downstream of the rotor, one with vanes and one without. Tests were conducted at two rotational speeds and a range of flow conditions was achieved by varying the annulus and sealing mass flow rates. Concentration effectiveness, swirl and steady pressure measurements separated, for the first time, the influence of the blades and vanes on ingress over a wide range of flow conditions. Measurements on the downstream stator platform provide added insight into the complex interaction between the egress and the mainstream. Measurements of unsteady pressure revealed the presence of large-scale structures, even in the absence of blades. The number and speed of the structures was shown to depend on the flow coefficient and the purge flow rate.

An Advanced Single-Stage Turbine Facility for Investigating Non-Axisymmetric Contoured Endwalls in the Presence of Purge Flow

2019 ◽  
Author(s):  
Robin R. Jones ◽  
Oliver J. Pountney ◽  
Bjorn L. Cleton ◽  
Liam E. Wood ◽  
B. Deneys J. Schreiner ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Static Pressure ◽  
Optical Measurement ◽  
Guide Vane ◽  
Single Stage ◽  
Test Facility ◽  
Pressure Distributions ◽  
Mainstream Flow ◽  
Purge Flow ◽  
Nozzle Guide

Abstract In modern gas turbines, endwall contouring (EWC) is employed to modify the static pressure field downstream of the vanes and minimise the growth of secondary flow structures developed in the blade passage. Purge flow (or egress) from the upstream rim-seal interferes with the mainstream flow, adding to the loss generated in the rotor. Despite this, EWC is typically designed without consideration of mainstream-egress interactions. The performance gains offered by EWC can be reduced, or in the limit eliminated, when purge air is considered. In addition, EWC can result in a reduction in sealing effectiveness across the rim seal. Consequently, industry is pursuing a combined design approach that encompasses the rim-seal, seal-clearance profile and EWC on the rotor endwall. This paper presents the design of, and preliminary results from a new single-stage axial turbine facility developed to investigate the fundamental fluid dynamics of egress-mainstream flow interactions. To the authors’ knowledge this is the only test facility in the world capable of investigating the interaction effects between cavity flows, rim seals and EWC. The design of optical measurement capabilities for future studies, employing volumetric velocimetry and planar laser induced fluorescence are also presented. The fluid-dynamically scaled rig operates at benign pressures and temperatures suited to these techniques and is modular. The facility enables expedient interchange of EWC (integrated into the rotor bling), blade-fillet and rim-seals geometries. The measurements presented in this paper include: gas concentration effectiveness and swirl measurements on the stator wall and in the wheel-space core; pressure distributions around the nozzle guide vanes at three different spanwise locations; pitchwise static pressure distributions downstream of the nozzle guide vane at four axial locations on the stator platform.

Erosion Testing of Thermal Barrier Coatings in a High Enthalpy Wind Tunnel

2014 ◽  
Author(s):  
M. Kirschner ◽  
T. Wobst ◽  
B. Rittmeister ◽  
Ch. Mundt
Keyword(s):  
Wind Tunnel ◽  
Thermal Barrier Coatings ◽  
Gas Turbines ◽  
Test Facility ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Coating Degradation ◽  
Air Jet ◽  
Erosion Test ◽  
Engine Components

One of the major problems facing the users of aircraft engines and stationary gas turbines in dusty and dirty environments is erosion, causing engine performance deterioration. Thermal barrier coatings (TBCs) are often applied on metal engine components as combustor heat shields or tiles as well as turbine blades allowing enhanced operating temperatures and resulting in increased thermal efficiency of the turbine and also reduced fuel consumption and gaseous emission. Erosive attack by airborne dust or fly ash, coarse particles causes coating degradation resulting in lifing issues of engine components. In the present study an erosion test facility was used to simulate the mechanisms of coating degradation expected in gas turbines in a more realistic way closer to real engine conditions. A loading situation combining thermal gradient cycling and erosive media was used. The experiments has been performed with an arc heated plasma wind tunnel (total enthalpy up to 20 MJ/kg), which is available at the Institute for Thermodynamics at the University of the Federal Armed Forces in Munich, Germany. The experimental setup and the integration of the air jet erosion test rig into the existing plasma wind tunnel will be elucidated. Different plasma sprayed thermal barrier coating materials, including the standard TBC material yttria-stabilised zirconia, were investigated regarding their erosion resistance. For validation and verification, samples of nickel-based Mar-M 247 and INCO 718 alloys have been used.

Oxy-Fuel Gas Turbine, Gas Generator and Reheat Combustor Technology Development and Demonstration

2010 ◽  
Author(s):  
Roger Anderson ◽  
Fermin Viteri ◽  
Rebecca Hollis ◽  
Ashley Keating ◽  
Jonathan Shipper ◽  
...  
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Clean Energy ◽  
Test Facility ◽  
Working Fluid ◽  
Capital Costs ◽  
2Nd Generation ◽  
Wide Range ◽  
And Performance

Future fossil-fueled power generation systems will require carbon capture and sequestration to comply with government green house gas regulations. The three prime candidate technologies that capture carbon dioxide (CO2) are pre-combustion, post-combustion and oxy-fuel combustion techniques. Clean Energy Systems, Inc. (CES) has recently demonstrated oxy-fuel technology applicable to gas turbines, gas generators, and reheat combustors at their 50MWth research test facility located near Bakersfield, California. CES, in conjunction with Siemens Energy, Inc. and Florida Turbine Technologies, Inc. (FTT) have been working to develop and demonstrate turbomachinery systems that accommodate the inherent characteristics of oxy-fuel (O-F) working fluids. The team adopted an aggressive, but economical development approach to advance turbine technology towards early product realization; goals include incremental advances in power plant output and efficiency while minimizing capital costs and cost of electricity [1]. Proof-of-concept testing was completed via a 20MWth oxy-fuel combustor at CES’s Kimberlina prototype power plant. Operability and performance limits were explored by burning a variety of fuels, including natural gas and (simulated) synthesis gas, over a wide range of conditions to generate a steam/CO2 working fluid that was used to drive a turbo-generator. Successful demonstration led to the development of first generation zero-emission power plants (ZEPP). Fabrication and preliminary testing of 1st generation ZEPP equipment has been completed at Kimberlina power plant (KPP) including two main system components, a large combustor (170MWth) and a modified aeroderivative turbine (GE J79 turbine). Also, a reheat combustion system is being designed to improve plant efficiency. This will incorporate the combustion cans from the J79 engine, modified to accept the system’s steam/CO2 working fluid. A single-can reheat combustor has been designed and tested to verify the viability and performance of an O-F reheater can. After several successful tests of the 1st generation equipment, development started on 2nd generation power plant systems. In this program, a Siemens SGT-900 gas turbine engine will be modified and utilized in a 200MWe power plant. Like the 1st generation system, the expander section of the engine will be used as an advanced intermediate pressure turbine and the can-annular combustor will be modified into a O-F reheat combustor. Design studies are being performed to define the modifications necessary to adapt the hardware to the thermal and structural demands of a steam/CO2 drive gas including testing to characterize the materials behavior when exposed to the deleterious working environment. The results and challenges of 1st and 2nd generation oxy-fuel power plant system development are presented.

Ultra-Low NOx Advanced Vortex Combustor

2006 ◽  
Author(s):  
Ryan G. Edmonds ◽  
Robert C. Steele ◽  
Joseph T. Williams ◽  
Douglas L. Straub ◽  
Kent H. Casleton ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Test Facility ◽  
Attractive Alternative ◽  
Lean Premixed Combustion ◽  
Pressure Drops ◽  
Wide Range ◽  
Lean Premixed

An ultra lean-premixed Advanced Vortex Combustor (AVC) has been developed and tested. The natural gas fueled AVC was tested at the U.S. Department of Energy’s National Energy Technology Laboratory (USDOE NETL) test facility in Morgantown (WV). All testing was performed at elevated pressures and inlet temperatures and at lean fuel-air ratios representative of industrial gas turbines. The improved AVC design exhibited simultaneous NOx/CO/UHC emissions of 4/4/0 ppmv (all emissions are at 15% O2 dry). The design also achieved less than 3 ppmv NOx with combustion efficiencies in excess of 99.5%. The design demonstrated tremendous acoustic dynamic stability over a wide range of operating conditions which potentially makes this approach significantly more attractive than other lean premixed combustion approaches. In addition, a pressure drop of 1.75% was measured which is significantly lower than conventional gas turbine combustors. Potentially, this lower pressure drop characteristic of the AVC concept translates into overall gas turbine cycle efficiency improvements of up to one full percentage point. The relatively high velocities and low pressure drops achievable with this technology make the AVC approach an attractive alternative for syngas fuel applications.

Design of an Improved Turbine Rim-Seal

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
James A. Scobie ◽  
Roy Teuber ◽  
Yan Sheng Li ◽  
Carl M. Sangan ◽  
Michael Wilson ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Navier Stokes ◽  
Computational Time ◽  
Gas Concentration ◽  
Engine Design ◽  
Successful Design ◽  
Purge Flow ◽  
Rotor Disk ◽  
Computational Fluid Dynamics Cfd ◽  
Improved Performance

Rim seals are fitted in gas turbines at the periphery of the wheel-space formed between rotor disks and their adjacent casings. These seals, also called platform overlap seals, reduce the ingress of hot gases which can limit the life of highly stressed components in the engine. This paper describes the development of a new, patented rim-seal concept showing improved performance relative to a reference engine design, using unsteady Reynolds-averaged Navier–Stokes (URANS) computations of a turbine stage at engine conditions. The computational fluid dynamics (CFD) study was limited to a small number of purge-flow rates due to computational time and cost, and the computations were validated experimentally at a lower rotational Reynolds number and in conditions under incompressible flow. The new rim seal features a stator-side angel wing and two buffer cavities between outer and inner seals: the angel-wing promotes a counter-rotating vortex to reduce the effect of the ingress on the stator; the two buffer cavities are shown to attenuate the circumferential pressure asymmetries of the fluid ingested from the mainstream annulus. Rotor disk pumping is exploited to reduce the sealing flow rate required to prevent ingress, with the rotor boundary layer also providing protective cooling. Measurements of gas concentration and swirl ratio, determined from static and total pressure, were used to assess the performance of the new seal concept relative to a benchmark generic seal. The radial variation of concentration through the seal was measured in the experiments and these data captured the improvements due to the intermediate buffer cavities predicted by the CFD. This successful design approach is a potent combination of insight provided by computation, and the flexibility and expedience provided by experiment.

Sign in / Sign up

Export Citation Format

Share Document