Ultra-Low NOx Advanced Vortex Combustor

2006 ◽  
Author(s):  
Ryan G. Edmonds ◽  
Robert C. Steele ◽  
Joseph T. Williams ◽  
Douglas L. Straub ◽  
Kent H. Casleton ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Test Facility ◽  
Attractive Alternative ◽  
Lean Premixed Combustion ◽  
Pressure Drops ◽  
Wide Range ◽  
Lean Premixed

An ultra lean-premixed Advanced Vortex Combustor (AVC) has been developed and tested. The natural gas fueled AVC was tested at the U.S. Department of Energy’s National Energy Technology Laboratory (USDOE NETL) test facility in Morgantown (WV). All testing was performed at elevated pressures and inlet temperatures and at lean fuel-air ratios representative of industrial gas turbines. The improved AVC design exhibited simultaneous NOx/CO/UHC emissions of 4/4/0 ppmv (all emissions are at 15% O2 dry). The design also achieved less than 3 ppmv NOx with combustion efficiencies in excess of 99.5%. The design demonstrated tremendous acoustic dynamic stability over a wide range of operating conditions which potentially makes this approach significantly more attractive than other lean premixed combustion approaches. In addition, a pressure drop of 1.75% was measured which is significantly lower than conventional gas turbine combustors. Potentially, this lower pressure drop characteristic of the AVC concept translates into overall gas turbine cycle efficiency improvements of up to one full percentage point. The relatively high velocities and low pressure drops achievable with this technology make the AVC approach an attractive alternative for syngas fuel applications.

Low NOx Advanced Vortex Combustor

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Ryan G. Edmonds ◽  
Joseph T. Williams ◽  
Robert C. Steele ◽  
Douglas L. Straub ◽  
Kent H. Casleton ◽  
...  
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Attractive Alternative ◽  
Lean Premixed Combustion ◽  
Wide Range ◽  
Lean Premixed ◽  
Industrial Gas Turbines ◽  
Lean Fuel

A lean-premixed advanced vortex combustor (AVC) has been developed and tested. The natural gas fueled AVC was tested at the U.S. Department of Energy’s National Energy Technology Laboratory in Morgantown, WV. All testing was performed at elevated pressures and inlet temperatures and at lean fuel-air ratios representative of industrial gas turbines. The improved AVC design exhibited simultaneous NOx∕CO∕unburned hydrocarbon (UHC) emissions of 4∕4∕0ppmv (all emissions corrected to 15% O2 dry). The design also achieved less than 3ppmvNOx with combustion efficiencies in excess of 99.5%. The design demonstrated marked acoustic dynamic stability over a wide range of operating conditions, which potentially makes this approach significantly more attractive than other lean-premixed combustion approaches. In addition, the measured 1.75% pressure drop is significantly lower than conventional gas turbine combustors, which could translate into an overall gas turbine cycle efficiency improvement. The relatively high velocities and low pressure drop achievable with this technology make the AVC approach an attractive alternative for syngas fuel applications.

Experimental Investigations of Pressure Drop in the Combustion Chamber of Gas Turbine

1989 ◽  
Author(s):  
Marek Dzida ◽  
Krzysztof Kosowski
Keyword(s):  
Pressure Drop ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Relative Pressure ◽  
Wide Range ◽  
Few Data

In bibliography we can find many methods of determining pressure drop in the combustion chambers of gas turbines, but there is only very few data of experimental results. This article presents the experimental investigations of pressure drop in the combustion chamber over a wide range of part-load performances (from minimal power up to take-off power). Our research was carried out on an aircraft gas turbine of small output. The experimental results have proved that relative pressure drop changes with respect to fuel flow over the whole range of operating conditions. The results were then compared with theoretical methods.

scholarly journals Measurement of Air-Fuel Ratio Fluctuations Caused by Combustor Driven Oscillations

1998 ◽  
Author(s):  
Rajiv Mongia ◽  
Robert Dibble ◽  
Jeff Lovett
Keyword(s):  
Power Spectrum ◽  
Mole Fraction ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Pollutant Emissions ◽  
Combustion Instabilities ◽  
Pressure Oscillations ◽  
Lean Premixed Combustion ◽  
Lean Premixed

Lean premixed combustion has emerged as a method of achieving low pollutant emissions from gas turbines. A common problem of lean premixed combustion is combustion instability. As conditions inside lean premixed combustors approach the lean flammability limit, large pressure variations are encountered. As a consequence, certain desirable gas turbine operating regimes are not approachable. In minimizing these regimes, combustor designers must rely upon trial and error because combustion instabilities are not well understood (and thus difficult to model). When they occur, pressure oscillations in the combustor can induce fluctuations in fuel mole fraction that can augment the pressure oscillations (undesirable) or dampen the pressure oscillations (desirable). In this paper, we demonstrate a method for measuring the fuel mole fraction oscillations which occur in the premixing section during combustion instabilities produced in the combustor that is downstream of the premixer. The fuel mole fraction in the premixer is measured with kHz resolution by the absorption of light from a 3.39 μm He-Ne laser. A sudden expansion combustor is constructed to demonstrate this fuel mole fraction measurement technique. Under several operating conditions, we measure significant fuel mole fraction fluctuations that are caused by pressure oscillations in the combustion chamber. Since the fuel mole fraction is sampled continuously, a power spectrum is easily generated. The fuel mole fraction power spectrum clearly indicates fuel mole fraction fluctuation frequencies are the same as the pressure fluctuation frequencies under some operating conditions.

Uncertainty Analysis of Inflow Conditions on an HPT Gas Turbine Nozzle: Effect on Particle Deposition

2020 ◽  
Author(s):  
R. Friso ◽  
N. Casari ◽  
M. Pinelli ◽  
A. Suman ◽  
F. Montomoli
Keyword(s):  
Gas Turbine ◽  
Energy Efficient ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Operating Conditions ◽  
Wide Range ◽  
And Performance ◽  
Gas Turbine Nozzle ◽  
The Impact ◽  
Inflow Conditions

Abstract Gas turbines (GT) are often forced to operate in harsh environmental conditions. Therefore, the presence of particles in their flow-path is expected. With this regard, deposition is a problem that severely affects gas turbine operation. Components’ lifetime and performance can dramatically vary as a consequence of this phenomenon. Unfortunately, the operating conditions of the machine can vary in a wide range, and they cannot be treated as deterministic. Their stochastic variations greatly affect the forecasting of life and performance of the components. In this work, the main parameters considered affected by the uncertainty are the circumferential hot core location and the turbulence level at the inlet of the domain. A stochastic analysis is used to predict the degradation of a high-pressure-turbine (HPT) nozzle due to particulate ingestion. The GT’s component analyzed as a reference is the HPT nozzle of the Energy-Efficient Engine (E3). The uncertainty quantification technique used is the probabilistic collocation method (PCM). This work shows the impact of the operating conditions uncertainties on the performance and lifetime reduction due to deposition. Sobol indices are used to identify the most important parameter and its contribution to life. The present analysis enables to build confidence intervals on the deposit profile and on the residual creep-life of the vane.

Analysis of Part Electric Gas Turbine: A Novel Hybrid Propulsion Concept

2019 ◽  
Author(s):  
M. S. N. Murthy ◽  
Subhash Kumar ◽  
Sheshadri Sreedhara
Keyword(s):  
Gas Turbine ◽  
Electric Motor ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Variable Speed ◽  
Hybrid Propulsion ◽  
Design Point ◽  
Part Load ◽  
Wide Range ◽  
Efficient Option

Abstract A gas turbine engine (GT) is very complex to design and manufacture considering the power density it offers. Development of a GT is also iterative, expensive and involves a long lead time. The components of a GT, viz compressor, combustor and turbine are strongly dependent on each other for the overall performance characteristics of the GT. The range of compressor operation is dependent on the functional and safe limits of surging and choking. The turbine operating speeds are required to be matched with that of compressor for wide range of operating conditions. Due to this constrain, design for optimum possible performance is often sacrificed. Further, once catered for a design point, gas turbines offer low part load efficiencies at conditions away from design point. As a more efficient option, a GT is practically achievable in a split configuration, where the compressor and turbine rotate on different shafts independently. The compressor is driven by a variable speed electric motor. The power developed in the combustor using the compressed air from the compressor and fuel, drives the turbine. The turbine provides mechanical shaft power through a gear box if required. A drive taken from the shaft rotates an electricity generator, which provides power for the compressor’s variable speed electric motor through a power bank. Despite introducing, two additional power conversions compared to a conventional GT, this split configuration named as ‘Part Electric Gas Turbine’, has a potential for new applications and to achieve overall better efficiencies from a GT considering the poor part load characteristics of a conventional GT.

scholarly journals Variable Geometry Fuel Injector for Low Emissions Gas Turbines

1999 ◽  
Author(s):  
K. Smith ◽  
R. Steele ◽  
J. Rogers
Keyword(s):  
Gas Turbines ◽  
Field Tests ◽  
Flow Distribution ◽  
Operating Conditions ◽  
Variable Geometry ◽  
Fuel Injector ◽  
System Variable ◽  
Lean Premixed Combustion ◽  
Stable Operating ◽  
Lean Premixed

To extend the stable operating range of a lean premixed combustion system, variable geometry can be used to adjust the combustor air flow distribution as gas turbine operating conditions vary. This paper describes the design and preliminary testing of a lean premixed fuel injector that provides the variable geometry function. Test results from both rig and engine evaluations using natural gas are presented. The variable geometry injector has proven successful in the short-term testing conducted to date. Longer term field tests are planned to demonstrate durability.

Analysis of Gas Turbine Rotating Cavities by an One-Dimensional Model

2009 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Bruno Facchini ◽  
Luca Innocenti ◽  
Mirko Micio
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Design Tool ◽  
Operating Conditions ◽  
Outer Flow ◽  
One Dimensional ◽  
Wide Range ◽  
Air System ◽  
Secondary Air ◽  
Radial Outflow

Reliable design of secondary air system is one of the main tasks for the safety, unfailing and performance of gas turbine engines. To meet the increasing demands of gas turbines design, improved tools in prediction of the secondary air system behavior over a wide range of operating conditions are needed. A real gas turbine secondary air system includes several components, therefore its analysis is not carried out through a complete CFD approach. Usually, that predictions are performed using codes, based on simplified approach which allows to evaluate the flow characteristics in each branch of the air system requiring very poor computational resources and few calculation time. Generally the available simplified commercial packages allow to correctly solve only some of the components of a real air system and often the elements with a more complex flow structure cannot be studied; among such elements, the analysis of rotating cavities is very hard. This paper deals with a design-tool developed at the University of Florence for the simulation of rotating cavities. This simplified in-house code solves the governing equations for steady one-dimensional axysimmetric flow using experimental correlations both to incorporate flow phenomena caused by multidimensional effects, like heat transfer and flow field losses, and to evaluate the circumferential component of velocity. Although this calculation approach does not enable a correct modeling of the turbulent flow within a wheel space cavity, the authors tried to create an accurate model taking into account the effects of inner and outer flow extraction, rotor and stator drag, leakages, injection momentum and, finally, the shroud/rim seal effects on cavity ingestion. The simplified calculation tool was designed to simulate the flow in a rotating cavity with radial outflow both with a Batchelor and/or Stewartson flow structures. A primary 1D-code testing campaign is available in the literature [1]. In the present paper the authors develop, using CFD tools, reliable correlations for both stator and rotor friction coefficients and provide a full 1D-code validation comparing, due to lack of experimental data, the in house design-code predictions with those evaluated by CFD.

Exploration of Compact Combustors for Reheat Cycle Aero Engine Applications

2006 ◽  
Author(s):  
J. Zelina ◽  
D. T. Shouse ◽  
J. S. Stutrud ◽  
G. J. Sturgess ◽  
W. M. Roquemore
Keyword(s):  
Gas Turbine ◽  
Temperature Rise ◽  
Gas Turbines ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Combustion System ◽  
Turbine Engine ◽  
Lean Blowout ◽  
Power Extraction ◽  
Wide Range

An aero gas turbine engine has been proposed that uses a near-constant-temperature (NCT) cycle and an Inter-Turbine Burner (ITB) to provide large amounts of power extraction from the low-pressure turbine. This level of energy is achieved with a modest temperature rise across the ITB. The additional energy can be used to power a large geared fan for an ultra-high bypass ratio transport aircraft, or to drive an alternator for large amounts of electrical power extraction. Conventional gas turbines engines cannot drive ultra-large diameter fans without causing excessively high turbine temperatures, and cannot meet high power extraction demands without a loss of engine thrust. Reducing the size of the combustion system is key to make use of a NCT gas turbine cycle. Ultra-compact combustor (UCC) concepts are being explored experimentally. These systems use high swirl in a circumferential cavity about the engine centerline to enhance reaction rates via high cavity g-loading on the order of 3000 g’s. Any increase in reaction rate can be exploited to reduce combustor volume. The UCC design integrates compressor and turbine features which will enable a shorter and potentially less complex gas turbine engine. This paper will present experimental data of the Ultra-Compact Combustor (UCC) performance in vitiated flow. Vitiation levels were varied from 12–20% oxygen levels to simulate exhaust from the high pressure turbine (HPT). Experimental results from the ITB at atmospheric pressure indicate that the combustion system operates at 97–99% combustion efficiency over a wide range of operating conditions burning JP-8 +100 fuel. Flame lengths were extremely short, at about 50% of those seen in conventional systems. A wide range of operation is possible with lean blowout fuel-air ratio limits at 25–50% below the value of current systems. These results are significant because the ITB only requires a small (300°F) temperature rise for optimal power extraction, leading to operation of the ITB at near-lean-blowout limits of conventional combustor designs. This data lays the foundation for the design space required for future engine designs.

Flameholding Tendencies of Natural Gas and Hydrogen Flames at Gas Turbine Premixer Conditions

2014 ◽  
Author(s):  
Elliot Sullivan-Lewis ◽  
Vincent McDonell
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
High Reliability ◽  
Elevated Pressure ◽  
Inlet Temperature ◽  
Increased Risk ◽  
Wide Range ◽  
Lean Premixed

Ground based gas turbines are responsible for generating a significant amount of electric power as well as providing mechanical power for a variety of applications. This is due to their high efficiency, high power density, high reliability, and ability to operate on a wide range of fuels. Due to increasingly stringent air quality requirements, stationary power gas turbines have moved to lean-premixed operation. Lean-premixed operation maintains low combustion temperatures for a given turbine inlet temperature, resulting in low NOx emissions while minimizing emissions of CO and hydrocarbons. In addition, to increase overall cycle efficiency, engines are being operated at higher pressure ratios and/or higher combustor inlet temperatures. Increasing combustor inlet temperatures and pressures in combination with lean-premixed operation leads to increased reactivity of the fuel/air mixture, leading to increased risk of potentially damaging flashback. Curtailing flashback on engines operated on hydrocarbon fuels requires care in design of the premixer. Curtailing flashback becomes more challenging when fuels with reactive components such as hydrogen are considered. Such fuels are gaining interest because they can be generated from both conventional and renewable sources and can be blended with natural gas as a means for storage of renewably generated hydrogen. The two main approaches for coping with flashback are either to design a combustor that is resistant to flashback, or to design one that will not anchor a flame if a flashback occurs. An experiment was constructed to determine the flameholding tendencies of various fuels on typical features found in premixer passage ways (spokes, steps, etc.) at conditions representative of a gas turbine premixer passage way. In the present work tests were conducted for natural gas and hydrogen between 3 and 9 atm, between 530 K and 650K, and free stream velocities from 40 to 100 m/s. Features considered in the present study include a spoke in the center of the channel and a step at the wall. The results are used in conjunction with existing blowoff correlations to evaluate flameholding propensity of these physical features over the range of conditions studied. The results illustrate that correlations that collapse data obtained at atmospheric pressure do not capture trends observed for spoke and wall step features at elevated pressure conditions. Also, a notable fuel compositional effect is observed.

Evaluation of Advanced Combustors for Dry NOx Suppression With Nitrogen Bearing Fuels in Utility and Industrial Gas Turbines

1982 ◽  
Vol 104 (2) ◽  
pp. 429-438 ◽  
Author(s):  
M. B. Cutrone ◽  
M. B. Hilt ◽  
A. Goyal ◽  
E. E. Ekstedt ◽  
J. Notardonato
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Water Injection ◽  
Operating Conditions ◽  
Department Of Energy ◽  
Technical Program ◽  
Wide Range ◽  
Industrial Gas Turbines ◽  
Low Levels

The work described in this paper is part of the DOE/LeRC Advanced Conversion-Technology Project (ACT). The program is a multiple contract effort with funding provided by the Department of Energy, and technical program management provided by NASA LeRC. Combustion tests are in progress to evaluate the potential of seven advanced combustor concepts for achieving low NOx emissions for utility gas turbine engines without the use of water injection. Emphasis was on the development of the required combustor aerothermodynamic features for burning high nitrogen fuels. Testing was conducted over a wide range of operating conditions for a 12:1 pressure ratio heavy-duty gas turbine. Combustors were evaluated with distillate fuel, SRC-II coal-derived fuel, residual fuel, and blends. Test results indicate that low levels of NOx and fuel-bound nitrogen conversion can be achieved with rich-lean combustors for fuels with high fuel-bound nitrogen. In addition, ultra-low levels of NOx can be achieved with lean-lean combustors for fuels with low fuel-bound nitrogen.

Sign in / Sign up

Export Citation Format

Share Document