The Benefit of Using Multiple Thin Tanks Versus a Short Big Tank for Thermal Storage in Ceramic-Sphere Packed Bed With Airflow

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Yan Wang ◽  
Peiwen Li ◽  
Zhifeng Wang ◽  
Bei Yang ◽  
Guofeng Yuan
Keyword(s):  
Heat Transfer ◽  
Storage System ◽  
Large Diameter ◽  
Small Diameter ◽  
Operation Time ◽  
Thermal Storage ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Optimization Methodology ◽  
Energy Storage Efficiency

Abstract To make a better thermal storage system that uses air as the heat transfer fluid flowing through a packed-bed of ceramic spheres (Al2O3) as thermal storage materials, the present work studied cases using multiple small-diameter thin tanks to replace a large-diameter big tank while keeping the same total volume and the same air flow rate. Performance analysis of thermal storage has been conducted for comparison and optimization. The long flow passage and faster flow velocity of air in the small-diameter tanks was found to significantly benefit thermal storage performance compared with that of a short big tank. It resulted in a longer duration of discharge of high-temperature airflow, if the same operation time is applied to the two situations. The faster airflow enhances the heat transfer between air and thermal storage material, although it incurs larger pressure loss. Overall, the energy storage efficiency of using several thin tanks can be significantly better than that of using a big short tank if the height-to-diameter ratio in the multiple thin tanks is properly optimized. The optimization methodology and results are of great significance to the development of thermal storage systems that use air as heat transfer fluid and rocks or ceramic spheres as the packed-bed material for thermal storage.

Experimental Investigation of Thermal Storage Processes in a Thermocline Storage Tank

2011 ◽  
Author(s):  
Wafaa Karaki ◽  
Peiwen Li ◽  
Jon Van Lew ◽  
M. M. Valmiki ◽  
Cholik Chan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Storage Tank ◽  
Power Plants ◽  
Thermal Power ◽  
Energy Charge ◽  
Thermal Storage ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Energy Storage Efficiency

This paper presents an experimental study and analysis of the heat transfer of energy charge and discharge in a packed-bed thermocline thermal storage tank for application in concentrated solar thermal power plants. Because the energy storage efficiency is a function of many parameters including fluid and solid properties, tank dimensions, packing dimensions, and time lengths of charge and discharge, this paper aims to provide experimental data and a proper approach of data reduction and presentation. To accomplish this goal, dimensionless governing equations of energy conservation in the heat transfer fluid and solid packed-bed material are derived. The obtained experimental data will provide a basis for validation of mathematical models in the future.

Longer Passage of Airflow in Multiple Packed-Bed Thin Tanks Versus in a Short Big Tank for Improved Thermal Storage Performance

2018 ◽  
Author(s):  
Yan Wang ◽  
Peiwen Li ◽  
Zhifeng Wang ◽  
Bei Yang ◽  
Guofeng Yuan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Storage System ◽  
Thermal Power ◽  
Thermal Storage ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Storage Efficiency ◽  
Storage Material ◽  
Solar Thermal Power ◽  
Storage Performance

A very challenging issue about solar thermal power generation is the use of a high temperature heat transfer fluid (water, oils, or molten salts) for heat transfer and thermal storage material, which may freeze at night or cold weather. When choosing air as the heat transfer fluid, the problem of freezing is eliminated. In order to increase the performance of thermal storage system which uses air as the heat transfer fluid passing through a packed bed (by ceramic spheres of Al2O3), multiple small-diameter tanks are considered to replace a single large-diameter tank with the same packed-bed volume and airflow rate in this paper. Analysis about the thermal storage performance in a short big tank and in cascade thin tanks has been made for comparison. A long passage of airflow and faster flow speed of air in the cascade thin tanks has been found significantly beneficial to thermal storage. Results about the increased thermal storage performance and increased pressure loss will be presented. Longer passage of airflow made it possible to have a longer time of high temperature of outflow air during discharging period. And faster speed of the fluid enhanced the heat transfer between air and thermal storage material. The total effective energy and thermal storage efficiency of cascade thin-tank thermal energy storage (TES) are higher. The thermal storage efficiency in the two types of thermal storage arrangement was compared for optimal design. The obtained results are of great significance to the development of using air as heat transfer fluid and rocks or ceramic spheres as the thermal storage material for thermal storage system in concentrated solar thermal power plants.

Numerical Study of Thermochemical Storage Using Ca(OH)2/CaO: High Temperature Applications

2016 ◽  
Author(s):  
Qasim A. Ranjha ◽  
Nasser Vahedi ◽  
Alparslan Oztekin
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Numerical Study ◽  
Storage System ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Operational Parameters ◽  
Storage And Retrieval

Thermal energy storage by reversible gas-solid reaction has been selected as a thermochemical energy storage system. Simulations are conducted to investigate the dehydration of Ca(OH)2 and the hydration of CaO for thermal energy storage and retrieval, respectively. The rectangular packed bed is heated indirectly by air used as a heat transfer fluid (HTF) while the steam is transferred through the upper side of the bed. Transient mass transport and heat transfer equations coupled with chemical kinetics equations for a two dimensional geometry have been solved using finite element method. Numerical results have been validated by comparing against results of previous measurements and simulations. The effect of geometrical and operational parameters including the material properties on overall storage and retrieval process has been investigated. The co-current and counter-current flow arrangements for steam and heat transfer fluid have been considered.

Experimental Study of a Novel Thermal Storage System Using Sands With High-Conductive Fluids Occupying the Pores

2014 ◽  
Author(s):  
Jingxiao Han ◽  
Ben Xu ◽  
Peiwen Li ◽  
Anurag Kumar ◽  
Yongping Yang
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Low Cost ◽  
Storage System ◽  
Solid Material ◽  
Thermal Storage ◽  
Heat Transfer Fluid ◽  
Large Capacity ◽  
Conductive Fluid ◽  
Media System

Because of the capability of large capacity thermal storage, concentrated solar power (CSP) technology is getting more attentions in the recent years. The energy storage allows power generation using solar energy during the late afternoon and evening time. For a large capacity of thermal energy storage, a dual-media system is typically adopted for reducing the use of the heat transfer fluid (HTF), which is usually expensive. In a dual-media system, the solid material must have large heat capacity and be inexpensive. One type of configuration for a dual-media system is that HTF flowing in pipes which are imbedded into the solid material. The present study considers sands, a major component of concrete, as low-cost solid thermal storage materials. The novel approach is that the sand is saturated with high thermal conductive fluid. Compared to using concrete for thermal storage, this method avoids issues of heat transfer degradation associated with the mismatch of thermal expansion of pipes and concrete. Since only sands are porous materials and the heat transfer performance is low, a high conductive fluid (XCELTHERM® 600 hot oil) was used to saturate sands, which then forms a new thermal storage material that can have better heat transfer. Results of thermal storage process with sands only and with the oil-saturated sands are presented and discussed.

Experimental Investigation of a Packed-Bed Latent Heat Thermal Storage System With Encapsulated Phase Change Material

2014 ◽  
Author(s):  
Tanvir E. Alam ◽  
Jaspreet Dhau ◽  
D. Y. Goswami ◽  
M. M. Rahman ◽  
Elias Stefankos
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Latent Heat ◽  
Flow Rate ◽  
Storage System ◽  
Volumetric Flow Rate ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Encapsulated Phase Change Material ◽  
Change Material

An experimental study on a laboratory scale prototype packed-bed latent heat thermal energy storage (TES) system is presented. Spherical capsules of sodium nitrate melting point of 306°C were used as the PCM and air was used as the heat transfer fluid (HTF). The storage system was operated between 286°C to 326°C and the volumetric flow rate of the HTF was varied from 110 m3/hr to 151 m3/hr. Temperature distribution along the bed and inside the capsules was monitored continuously during charging and discharging of the system. The effect of mass flow rate of the HTF on the charging and discharging time and on the pressure drop across the bed was also evaluated.

scholarly journals High-Temperature Chloride-Carbonate Phase Change Material: Thermal Performances and Modelling of a Packed Bed Storage System for Concentrating Solar Power Plants

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5339
Author(s):  
Giovanni Salvatore Sau ◽  
Valerio Tripi ◽  
Anna Chiara Tizzoni ◽  
Raffaele Liberatore ◽  
Emiliana Mansi ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Phase Change ◽  
Power Plants ◽  
Solar Power ◽  
Storage System ◽  
Ternary Eutectic ◽  
Thermal Storage ◽  
Packed Bed ◽  
Heat Transfer Fluid

Molten salts eutectics are promising candidates as phase change materials (PCMs) for thermal storage applications, especially considering the possibility to store and release heat at high temperatures. Although many compounds have been proposed for this purpose in the scientific literature, very few data are available regarding actual applications. In particular, there is a lack of information concerning thermal storage at temperatures around 600 °C, necessary for the coupling with a highly efficient Rankine cycle powered by concentrated solar power (CSP) plants. In this contest, the present work deals with a thermophysical behavior investigation of a storage heat exchanger containing a cost-effective and safe ternary eutectic, consisting of sodium chloride, potassium chloride, and sodium carbonate. This material was preliminarily and properly selected and characterized to comply with the necessary melting temperature and latent enthalpy. Then, an indirect heat exchanger was considered for the simulation, assuming aluminum capsules to confine the PCM, thus obtaining the maximum possible heat exchange surface and air at 5 bar as heat transfer fluid (HTF). The modelling was carried out setting the inlet and outlet air temperatures at, respectively, 290 °C and 550 °C, obtaining a realistic storage efficiency of around 0.6. Finally, a conservative investment cost was estimated for the storage system, demonstrating a real possible economic benefit in using these types of materials and heat exchange geometries, with the results varying, according to possible manufacturing prices, in a range from 25 to 40 EUR/kWh.

Numerical Simulation of Packed Bed Cubical Storage Unit Filled with Spherical Capsules of PCM

2018 ◽  
Vol 6 (3) ◽  
pp. 39-50
Author(s):  
Ahmed K. Alsharaa
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Small Diameter ◽  
Packed Bed ◽  
Energy Balance Equation ◽  
Conservation Equation ◽  
Heat Transfer Fluid ◽  
Storage Unit ◽  
Finite Differences Method ◽  
Melting Fraction

Modern life and increasing demand on the energy make the saving of available energy in the packed bed of PCM capsules very important to use in the other time. A numerical investigation is proposed for storage of thermal energy using packed bed of spherical capsules filled with phase change material PCM. The spherical capsules are arranged as layers in the cubic vessel that exposed to heat transfer fluid.  The fourth order Runge-Kutta method is applied to solve the energy balance equation of heat transfer fluid and the energy conservation equation of spherical capsules of PCM is solved using finite differences method with heat capacity method for phase change of PCM. The effect of Reynolds number and diameter of capsulated sphere are studied. The results illustrate that at constant porosity of packed bed the small diameter of capsulated spheres gives shorter time for melting, where at D=50mm & t=196.5sec the melting fraction of PCM is 0.09, while at D=10mm & t=196.5sec the melting fraction of PCM is 1.00. The results of present study have been compared with other previous results and give a good agreement.

Study of Turbulent Natural Convection in Vertical Storage Tubes for Supercritical Thermal Storage System

2013 ◽  
Author(s):  
Reza Baghaei Lakeh ◽  
H. Pirouz Kavehpour ◽  
Adrienne S. Lavine ◽  
Gani B. Ganapathi ◽  
Richard E. Wirz
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Flow Field ◽  
Storage System ◽  
Thermal Storage ◽  
Heat Transfer Fluid ◽  
Convection Flow ◽  
Vertical Orientation ◽  
Turbulent Natural Convection ◽  
Aspect Ratios

The effect of turbulent natural convection in vertical storage tubes containing a supercritical fluid is investigated computationally. In a supercritical thermal storage system, thermal energy is transferred to the storage fluid and is stored as the internal energy of the fluid in supercritical state. The heat is conducted from the heat transfer fluid to the storage fluid through the storage tube wall. Unlike phase-change systems, the heat transfer mechanism within the storage tubes of supercritical thermal storage system is dominantly affected by rigorous turbulent natural convection. The natural convection enhances the heat transfer and compensates for the low thermal conductivity of the storage fluid. The turbulent buoyancy-driven flow field in vertical storage tubes with different aspect ratios is investigated in this paper and the effect of vertical orientation of storage tubes on the characteristics of the flow field is explored. A standard k-epsilon method is utilized to model the Reynolds stresses in turbulent natural convection flow. The results of this study show that the turbulent buoyancy-driven flow and natural convection play an important role in charge and discharge of the supercritical thermal storage system. The charge time of the system is a function of Rayleigh number and aspect ratio of the storage tube.

Sign in / Sign up

Export Citation Format

Share Document