Experimental Study of a Novel Thermal Storage System Using Sands With High-Conductive Fluids Occupying the Pores

2014 ◽  
Author(s):  
Jingxiao Han ◽  
Ben Xu ◽  
Peiwen Li ◽  
Anurag Kumar ◽  
Yongping Yang
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Low Cost ◽  
Storage System ◽  
Solid Material ◽  
Thermal Storage ◽  
Heat Transfer Fluid ◽  
Large Capacity ◽  
Conductive Fluid ◽  
Media System

Because of the capability of large capacity thermal storage, concentrated solar power (CSP) technology is getting more attentions in the recent years. The energy storage allows power generation using solar energy during the late afternoon and evening time. For a large capacity of thermal energy storage, a dual-media system is typically adopted for reducing the use of the heat transfer fluid (HTF), which is usually expensive. In a dual-media system, the solid material must have large heat capacity and be inexpensive. One type of configuration for a dual-media system is that HTF flowing in pipes which are imbedded into the solid material. The present study considers sands, a major component of concrete, as low-cost solid thermal storage materials. The novel approach is that the sand is saturated with high thermal conductive fluid. Compared to using concrete for thermal storage, this method avoids issues of heat transfer degradation associated with the mismatch of thermal expansion of pipes and concrete. Since only sands are porous materials and the heat transfer performance is low, a high conductive fluid (XCELTHERM® 600 hot oil) was used to saturate sands, which then forms a new thermal storage material that can have better heat transfer. Results of thermal storage process with sands only and with the oil-saturated sands are presented and discussed.

Experimental Exploration of a Small Scale Pneumatically Pumped Thermal Storage System

2016 ◽  
Author(s):  
Inri Rodriguez ◽  
Jesus Cerda ◽  
Daniel S. Codd
Keyword(s):  
High Temperature ◽  
Storage Tank ◽  
Pulse Width Modulation ◽  
Low Cost ◽  
Storage System ◽  
Heat Engine ◽  
Thermal Storage ◽  
Heat Transfer Fluid ◽  
Small Scale ◽  
Constant Frequency

A prototype water-glycerol two tank storage system was designed to simulate the fluidic properties of a high temperature molten salt system while allowing for room temperature testing of a low cost, small scale pneumatically pumped thermal storage system for use in concentrated solar power (CSP) applications. Pressurized air is metered into a primary heat transfer fluid (HTF) storage tank; the airflow displaces the HTF through a 3D printed prototype thermoplate receiver and into a secondary storage tank to be dispatched in order to drive a heat engine during peak demand times. A microcontroller was programmed to use pulse-width modulation (PWM) to regulate air flow via an air solenoid. At a constant frequency of 10Hz, it was found that the lowest pressure drops and the slowest flowrates across the receiver occurred at low duty cycles of 15% and 20% and low inlet air pressures of 124 and 207 kPa. However, the data also suggested the possibility of slug flow. Replacement equipment and design modifications are suggested for further analysis and high temperature experiments. Nevertheless, testing demonstrated the feasibility of pneumatic pumping for small systems.

Numerical Study of Thermochemical Storage Using Ca(OH)2/CaO: High Temperature Applications

2016 ◽  
Author(s):  
Qasim A. Ranjha ◽  
Nasser Vahedi ◽  
Alparslan Oztekin
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Numerical Study ◽  
Storage System ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Operational Parameters ◽  
Storage And Retrieval

Thermal energy storage by reversible gas-solid reaction has been selected as a thermochemical energy storage system. Simulations are conducted to investigate the dehydration of Ca(OH)2 and the hydration of CaO for thermal energy storage and retrieval, respectively. The rectangular packed bed is heated indirectly by air used as a heat transfer fluid (HTF) while the steam is transferred through the upper side of the bed. Transient mass transport and heat transfer equations coupled with chemical kinetics equations for a two dimensional geometry have been solved using finite element method. Numerical results have been validated by comparing against results of previous measurements and simulations. The effect of geometrical and operational parameters including the material properties on overall storage and retrieval process has been investigated. The co-current and counter-current flow arrangements for steam and heat transfer fluid have been considered.

Exergy-Based Optimization of Sub- and Supercritical Thermal Energy Storage Systems

2014 ◽  
Author(s):  
Louis A. Tse ◽  
Reza Baghaei Lakeh ◽  
Richard E. Wirz ◽  
Adrienne S. Lavine
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Heat Transfer Fluid ◽  
Energy And Exergy

In this work, energy and exergy analyses are applied to a thermal energy storage system employing a storage medium in the two-phase or supercritical regime. First, a numerical model is developed to investigate the transient thermodynamic and heat transfer characteristics of the storage system by coupling conservation of energy with an equation of state to model the spatial and temporal variations in fluid properties during the entire working cycle of the TES tank. Second, parametric studies are conducted to determine the impact of key variables (such as heat transfer fluid mass flow rate and maximum storage temperature) on both energy and exergy efficiencies. The optimum heat transfer fluid mass flow rate during charging must balance exergy destroyed due to heat transfer and exergy destroyed due to pressure losses, which have competing effects. Similarly, the optimum maximum storage fluid temperature is evaluated to optimize exergetic efficiency. By incorporating exergy-based optimization alongside traditional energy analyses, the results of this study evaluate the optimal values for key parameters in the design and operation of TES systems, as well as highlight opportunities to minimize thermodynamic losses.

Effect of Natural Convection on Thermal Energy Storage in Supercritical Fluids

2013 ◽  
Author(s):  
Reza Baghaei Lakeh ◽  
Adrienne S. Lavine ◽  
H. Pirouz Kavehpour ◽  
Gani B. Ganapathi ◽  
Richard E. Wirz
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Natural Convection ◽  
Energy Storage ◽  
Supercritical Fluid ◽  
Supercritical Fluids ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Thermal Storage

Heat transfer to the storage fluid is a critical subject in thermal energy storage systems. The storage fluids that are proposed for supercritical thermal storage system are organic fluids that have poor thermal conductivity; therefore, pure conduction will not be an efficient heat transfer mechanism for the system. The current study concerns a supercritical thermal energy storage system consisting of horizontal tubes filled with a supercritical fluid. The results of this study show that the heat transfer to the supercritical fluid is highly dominated by natural convection. The buoyancy-driven flow inside the storage tubes dominates the flow field and enhances the heat transfer dramatically. Depending on the diameter of the storage tube, the buoyancy-driven flow may be laminar or turbulent. The natural convection has a significant effect on reducing the charge time compared to pure conduction. It was concluded that although the thermal conductivity of the organic supercritical fluids are relatively low, the effective laminar or turbulent natural convection compensates for this deficiency and enables the supercritical thermal storage to charge effectively.

Experimental Study of Thermal Energy Storage Using Natural Porous Media

2017 ◽  
Author(s):  
A. J. Al Edhari ◽  
C. C. Ngo
Keyword(s):  
Experimental Study ◽  
Porous Media ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Thermal Storage ◽  
Heat Transfer Fluid ◽  
Storage Unit ◽  
Storage Media

Thermal energy storage has been an area of research interest due to the need to store solar energy or excess energy for later use in many applications including district heating. The focus of a lot of research is on exotic and expensive storage media. This paper presents an experimental study of thermal energy storage using porous media readily available and commonly found in nature such as sand, soil, pebble rocks and gravel. This study also considers a simple and inexpensive thermal storage system which could be constructed easily and examines what could be done to increase the thermal storage performance. The thermal storage system examined in the present study was a thermal energy storage unit with embedded horizontal pipes carrying water as the heat transfer fluid for thermal charging. Different thermal storage configurations were examined by adjusting the thermal charging temperature and using different storage media. The temperature distribution within the storage media was monitored for 10 hours using a data acquisition system with K-type thermocouples. The results indicate that a thermal storage system using sand as storage media is slightly better compared with gravel or pebble rocks as storage media.

Numerical Investigation of Combined Sensible/Latent Heat Thermal Energy Storage With Supercritical Carbon Dioxide As Heat Transfer Fluid at 650°C

2019 ◽  
Author(s):  
Kelly Osterman ◽  
Diego Guillen ◽  
D. Yogi Goswami
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Energy Storage ◽  
Supercritical Carbon Dioxide ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Heat Storage ◽  
Storage System ◽  
Heat Transfer Fluid ◽  
Dry Air

Abstract This paper numerically explores a high-temperature sensible-latent hybrid thermal energy storage system designed to store heat with output temperatures stabilized at approximately 550–600 °C for direct coupling with supercritical carbon dioxide (sCO2) power cycles operating at their design point. sCO2 and dry air at 25 MPa are used as heat transfer fluid (HTF) in a packed bed storage system that combines rocks as sensible heat storage and AlSi12 as latent heat storage. The base model using dry air at atmospheric pressure is compared to similar work done at ETH Zurich; the model is then extended for use with sCO2 to compare the performance of air and sCO2 at similar volumetric flow rates. It was found that sCO2 is capable of storing a significantly larger amount of energy (∼40 kWh) in the same time period as the air system (∼19 kWh), and can discharge that energy much quicker (1.5 hours compared to 4 hours). However, in order to achieve similar degrees of temperature stabilization, the total height of PCM had to be increased significantly, from 9 cm to 45 cm or more.

Longer Passage of Airflow in Multiple Packed-Bed Thin Tanks Versus in a Short Big Tank for Improved Thermal Storage Performance

2018 ◽  
Author(s):  
Yan Wang ◽  
Peiwen Li ◽  
Zhifeng Wang ◽  
Bei Yang ◽  
Guofeng Yuan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Storage System ◽  
Thermal Power ◽  
Thermal Storage ◽  
Packed Bed ◽  
Heat Transfer Fluid ◽  
Storage Efficiency ◽  
Storage Material ◽  
Solar Thermal Power ◽  
Storage Performance

A very challenging issue about solar thermal power generation is the use of a high temperature heat transfer fluid (water, oils, or molten salts) for heat transfer and thermal storage material, which may freeze at night or cold weather. When choosing air as the heat transfer fluid, the problem of freezing is eliminated. In order to increase the performance of thermal storage system which uses air as the heat transfer fluid passing through a packed bed (by ceramic spheres of Al2O3), multiple small-diameter tanks are considered to replace a single large-diameter tank with the same packed-bed volume and airflow rate in this paper. Analysis about the thermal storage performance in a short big tank and in cascade thin tanks has been made for comparison. A long passage of airflow and faster flow speed of air in the cascade thin tanks has been found significantly beneficial to thermal storage. Results about the increased thermal storage performance and increased pressure loss will be presented. Longer passage of airflow made it possible to have a longer time of high temperature of outflow air during discharging period. And faster speed of the fluid enhanced the heat transfer between air and thermal storage material. The total effective energy and thermal storage efficiency of cascade thin-tank thermal energy storage (TES) are higher. The thermal storage efficiency in the two types of thermal storage arrangement was compared for optimal design. The obtained results are of great significance to the development of using air as heat transfer fluid and rocks or ceramic spheres as the thermal storage material for thermal storage system in concentrated solar thermal power plants.

Sign in / Sign up

Export Citation Format

Share Document