Modeling of Natural Gas Composition Effect on Low NOx Burners Operation in Heavy Duty Gas Turbine

2021 ◽  
Vol 143 (3) ◽  
Author(s):  
Serena Romano ◽  
Roberto Meloni ◽  
Giovanni Riccio ◽  
Pier Carlo Nassini ◽  
Antonio Andreini
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Deep Understanding ◽  
Combustion Efficiency ◽  
Gas Composition ◽  
Gas Combustion ◽  
Annular Combustor ◽  
Heavy Duty Gas Turbine ◽  
Minimal Environmental Impact ◽  
The Impact

Abstract This paper addresses the impact of natural gas composition on both the operability and emissions of lean premixed gas turbine combustion system. This is an issue of growing interest due to the challenge for gas turbine manufacturers in developing fuel-flexible combustors capable of operating with variable fuel gases while producing very low emissions at the same time. Natural gas contains primarily methane (CH4) but also notable quantities of higher order hydrocarbons such as ethane (C2H6) can also be present. A deep understanding of natural gas combustion is important to obtain the highest combustion efficiency with minimal environmental impact. For this purpose, Large Eddy Simulations of an annular combustor sector equipped with a partially premixed burner are carried out for two different natural gas compositions with and without including the effect of flame strain rate and heat loss resulting in a more adequate description of flame shape, thermal field, and extinction phenomena. Promising results, in terms of NOx, compared against available experimental data, are obtained including these effects on the flame brush modeling, enhancing the fuel-dependency under nonadiabatic condition.

Modeling of Natural Gas Composition Effect on Low NOx Burners Operation in Heavy Duty Gas Turbine

2020 ◽  
Author(s):  
S. Romano ◽  
R. Meloni ◽  
G. Riccio ◽  
P. C. Nassini ◽  
A. Andreini
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Deep Understanding ◽  
Combustion Efficiency ◽  
Gas Composition ◽  
Gas Combustion ◽  
Annular Combustor ◽  
Heavy Duty Gas Turbine ◽  
Minimal Environmental Impact ◽  
The Impact

Abstract This paper addresses the impact of natural gas composition on both the operability and emissions of lean premixed gas turbine combustion system. This is an issue of growing interest due to the challenge for gas turbine manufacturers in developing fuel-flexible combustors capable of operating with variable fuel gases while producing very low emissions at the same time. Natural gas contains primarily methane (CH4) but also notable quantities of higher order hydrocarbons such as ethane (C2H6) can also be present. A deep understanding of natural gas combustion is important to obtain the highest combustion efficiency with minimal environmental impact. For this purpose, Large Eddy Simulations of an annular combustor sector equipped with a partially-premixed burner are carried out for two different natural gas compositions with and without including the effect of flame strain rate and heat loss resulting in a more adequate description of flame shape, thermal field and extinction phenomena. Promising results, in terms of NOx, compared against available experimental data, are obtained including these effects on the flame brush modelling, enhancing the fuel-dependency under non adiabatic condition.

Effect of Natural Gas Composition on Low NOx Burners Operation in Heavy Duty Gas Turbine

2019 ◽  
Author(s):  
Serena Romano ◽  
Matteo Cerutti ◽  
Giovanni Riccio ◽  
Antonio Andreini ◽  
Christian Romano
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Operating Conditions ◽  
Fuel Composition ◽  
Gas Composition ◽  
Heavy Duty ◽  
Wide Range ◽  
Annular Combustor ◽  
Heavy Duty Gas Turbine ◽  
The Impact

Abstract Development of lean-premixed combustion technology with low emissions and stable operation in an increasingly wide range of operating conditions requires a deep understanding of the mechanisms that affect the combustion performance or even the operability of the entire gas turbine. Due to the relative wide range of natural gas composition supplies and the increased demand from Oil&Gas customers to burn unprocessed gas as well as LNG with notable higher hydrocarbons (C2+) content; the impact on gas turbine operability and combustion related aspects has been matter of several studies. In this paper, results of experimental test campaign of an annular combustor for heavy-duty gas turbine are presented with focus on the effect of fuel composition on both emissions and flame stability. Test campaign involved two different facilities, a full annular combustor rig and a full-scale prototype engine fed with different fuel mixtures of natural gas with small to moderate C2H6 content. Emissions trends and blowout for several operating conditions and burner configurations have been analyzed. Modifications to the burner geometry and fuel injection optimization have shown to be able to reach a good trade-off while keeping low NOx emissions in stable operating conditions for varying fuel composition.

Effect of Natural Gas Composition on Low Nox Burners Operation in Heavy Duty Gas Turbine

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Serena Romano ◽  
Matteo Cerutti ◽  
Giovanni Riccio ◽  
Antonio Andreini ◽  
Christian Romano
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Operating Conditions ◽  
Fuel Composition ◽  
Gas Composition ◽  
Heavy Duty ◽  
Wide Range ◽  
Annular Combustor ◽  
Heavy Duty Gas Turbine ◽  
The Impact

Abstract Development of lean-premixed combustion technology with low emissions and stable operation in an increasingly wide range of operating conditions requires a deep understanding of the mechanisms that affect the combustion performance or even the operability of the entire gas turbine. Due to the relative wide range of natural gas composition supplies and the increased demand from Oil&Gas customers to burn unprocessed gas as well as liquified natural gas (LNG) with notable higher hydrocarbons (C2+) content, the impact on gas turbine operability and combustion related aspects has been matter of several studies. In this paper, results of experimental test campaign of an annular combustor for heavy-duty gas turbine are presented with focus on the effect of fuel composition on both emissions and flame stability. Test campaign involved two different facilities, a full annular combustor rig and a full-scale prototype engine fed with different fuel mixtures of natural gas with small to moderate C2H6 content. Emission trends and blowout for several operating conditions and burner configurations have been analyzed. Modifications to the burner geometry and fuel injection optimization have shown to be able to reach a good tradeoff while keeping low NOx emissions in stable operating conditions for varying fuel composition.

Design Improvement Survey for NOx Emissions Reduction of a Heavy-Duty Gas Turbine Partially Premixed Fuel Nozzle Operating With Natural Gas: Experimental Campaign

2015 ◽  
Author(s):  
Matteo Cerutti ◽  
Roberto Modi ◽  
Danielle Kalitan ◽  
Kapil K. Singh
Keyword(s):  
Pressure Drop ◽  
Natural Gas ◽  
Gas Turbine ◽  
Pollutant Emissions ◽  
Nox Emissions ◽  
Heavy Duty ◽  
Fuel Nozzle ◽  
Partially Premixed ◽  
Heavy Duty Gas Turbine ◽  
The Impact

As government regulations become increasingly strict with regards to combustion pollutant emissions, new gas turbine combustor designs must produce lower NOx while also maintaining acceptable combustor operability. The design and implementation of an efficient fuel/air premixer is paramount to achieving low emissions. Options for improving the design of a natural gas fired heavy-duty gas turbine partially premixed fuel nozzle have been considered in the current study. In particular, the study focused on fuel injection and pilot/main interaction at high pressure and high inlet temperature. NOx emissions results have been reported and analyzed for a baseline nozzle first. Available experience is shared in this paper in the form of a NOx correlative model, giving evidence of the consistency of current results with past campaigns. Subsequently, new fuel nozzle premixer designs have been investigated and compared, mainly in terms of NOx emissions performance. The operating range of investigation has been preliminarily checked by means of a flame stability assessment. Adequate margin to lean blow out and thermo-acoustic instabilities onset has been found while also maintaining acceptable CO emissions. NOx emission data were collected over a variety of fuel/air ratios and pilot/main splits for all the fuel nozzle configurations. Results clearly indicated the most effective design option in reducing NOx. In addition, the impact of each design modification has been quantified and the baseline correlative NOx emissions model calibrated to describe the new fuel nozzles behavior. Effect of inlet air pressure has been evaluated and included in the models, allowing the extensive use of less costly reduced pressure test campaigns hereafter. Although the observed effect of combustor pressure drop on NOx is not dominant for this particular fuel nozzle, sensitivity has been performed to consolidate gathered experience and to make the model able to evaluate even small design changes affecting pressure drop.

Modeling of Natural Gas Composition Effect on Low NOX Burners Operation in Heavy Duty Gas Turbine

2021 ◽  
Author(s):  
Serena Romano ◽  
Roberto Meloni ◽  
Pier Carlo Nassini ◽  
Antonio Andreini ◽  
Giovanni Riccio
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Composition ◽  
Composition Effect ◽  
Heavy Duty ◽  
Heavy Duty Gas Turbine

Impact of Different Film-Cooling Modes at Trailing Edge on the Aerodynamic Performance of Heavy Duty Gas Turbine Cascade

2011 ◽  
Vol 84-85 ◽  
pp. 259-263
Author(s):  
Xun Liu ◽  
Song Tao Wang ◽  
Xun Zhou ◽  
Guo Tai Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Large Mass ◽  
Turbine Cascade ◽  
Heavy Duty ◽  
Trailing Edge ◽  
Central Difference ◽  
Adiabatic Effectiveness ◽  
Heavy Duty Gas Turbine ◽  
The Impact

In this paper, the trailing edge film cooling flow field of a heavy duty gas turbine cascade has been studied by central difference scheme and multi-block grid technique. The research is based on the three-dimensional N-S equation solver. By way of analysis of the temperature field, the distribution of profile pressure, and the distribution of film-cooling adiabatic effectiveness in the region of trailing edge with different cool air injection mass and different angles, it is found that the impact on the film-cooling adiabatic effectiveness is slightly by changing the injection mass. The distribution of profile pressure dropped intensely at the pressure side near the injection holes line with the large mass cooling air. The cooling effect is good in the region of trailing edge while the injection air is along the direction of stream.

Fuel Flexibility Influences on Premixed Combustor Blowout, Flashback, Autoignition and Instability

2006 ◽  
Author(s):  
Tim Lieuwen ◽  
Vince McDonell ◽  
Eric Petersen ◽  
Domenic Santavicca
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Dynamic Stability ◽  
Current Understanding ◽  
Fuel Composition ◽  
Fuel Flexibility ◽  
Lean Premixed ◽  
Gas Fuel ◽  
The Impact ◽  
Underlying Processes

This paper addresses the impact of fuel composition on the operability of lean premixed gas turbine combustors. This is an issue of current importance due to variability in the composition of natural gas fuel supplies and interest in the use of syngas fuels. Of particular concern is the effect of fuel composition on combustor blowout, flashback, dynamic stability, and autoignition. This paper reviews available results and current understanding of the effects of fuel composition on the operability of lean premixed combustors. It summarizes the underlying processes that must be considered when evaluating how a given combustor’s operability will be affected as fuel composition is varied.

A New Calculation Approach to the Energy Balance of a Gas Turbine Including a Study of the Impact of the Uncertainty of Measured Parameters

2005 ◽  
Author(s):  
Helmer G. Andersen ◽  
Pen-Chung Chen
Keyword(s):  
Energy Balance ◽  
Gas Turbine ◽  
Control Volume ◽  
Ambient Air ◽  
Energy Balance Equation ◽  
Inlet Temperature ◽  
Exhaust Gas ◽  
Gas Composition ◽  
Intake Flow ◽  
The Impact

Computing the solution to the energy balance around a gas turbine in order to calculate the intake mass flow and the turbine inlet temperature requires several iterations. This makes hand calculations very difficult and, depending on the software used, even causes significant calculation times on PCs. While this may not seem all that important considering the power of today’s personal computers, the approach described in this paper presents a new way of looking at the gas turbine process and the resulting simplifications in the calculations. This paper offers a new approach to compute the energy balance around a gas turbine. The energy balance requires that all energy flows going into and out of the control volume be accounted for. The difficulty of the energy balance equation around a gas turbine lies in the fact that the exhaust gas composition is unknown as long as the intake flow is unknown. Thus, a composition needs to be assumed when computing the exhaust gas enthalpy. This allows the calculation of the intake flow, which in turn provides a new exhaust gas composition, and so forth. By viewing the exhaust gas as a flow consisting of ambient air and combusted fuel, the described iteration can be avoided. The study presents the formulation of the energy balance applying this approach and looks at the accuracy of the result as a function of the inaccuracy of the input parameters. Furthermore, solutions of the energy balance are presented for various process scenarios, and the impact of the uncertainty of key process parameter is analyzed.

Gas Turbine Combined Cycle With CO2-Capture Using Auto-Thermal Reforming of Natural Gas

2000 ◽  
Author(s):  
Thormod Andersen ◽  
Hanne M. Kvamsdal ◽  
Olav Bolland
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Process Integration ◽  
Combined Cycle ◽  
Co2 Removal ◽  
Gas Turbine Combustor ◽  
Chemical Absorption ◽  
Fuel Gas ◽  
The Impact ◽  
Water Gas

A concept for capturing and sequestering CO2 from a natural gas fired combined cycle power plant is presented. The present approach is to decarbonise the fuel prior to combustion by reforming natural gas, producing a hydrogen-rich fuel. The reforming process consists of an air-blown pressurised auto-thermal reformer that produces a gas containing H2, CO and a small fraction of CH4 as combustible components. The gas is then led through a water gas shift reactor, where the equilibrium of CO and H2O is shifted towards CO2 and H2. The CO2 is then captured from the resulting gas by chemical absorption. The gas turbine of this system is then fed with a fuel gas containing approximately 50% H2. In order to achieve acceptable level of fuel-to-electricity conversion efficiency, this kind of process is attractive because of the possibility of process integration between the combined cycle and the reforming process. A comparison is made between a “standard” combined cycle and the current process with CO2-removal. This study also comprise an investigation of using a lower pressure level in the reforming section than in the gas turbine combustor and the impact of reduced steam/carbon ratio in the main reformer. The impact on gas turbine operation because of massive air bleed and the use of a hydrogen rich fuel is discussed.

The Impact of Gas Modeling in the Numerical Analysis of a Multistage Gas Turbine

2008 ◽  
Vol 130 (2) ◽  
Author(s):  
Filippo Rubechini ◽  
Michele Marconcini ◽  
Andrea Arnone ◽  
Massimiliano Maritano ◽  
Stefano Cecchi
Keyword(s):  
Gas Turbine ◽  
Flow Direction ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Ratio Distribution ◽  
Real Gas ◽  
Turbine Performance ◽  
Wall Boundary Conditions ◽  
Heavy Duty Gas Turbine ◽  
The Impact

In this work a numerical investigation of a four stage heavy-duty gas turbine is presented. Fully three-dimensional, multistage, Navier-Stokes analyses are carried out to predict the overall turbine performance. Coolant injections, cavity purge flows, and leakage flows are included in the turbine modeling by means of suitable wall boundary conditions. The main objective is the evaluation of the impact of gas modeling on the prediction of the stage and turbine performance parameters. To this end, four different gas models were used: three models are based on the perfect gas assumption with different values of constant cp, and the fourth is a real gas model which accounts for thermodynamic gas properties variations with temperature and mean fuel∕air ratio distribution in the through-flow direction. For the real gas computations, a numerical model is used which is based on the use of gas property tables, and exploits a local fitting of gas data to compute thermodynamic properties. Experimental measurements are available for comparison purposes in terms of static pressure values at the inlet∕outlet of each row and total temperature at the turbine exit.

Sign in / Sign up

Export Citation Format

Share Document