Implementation of Rectangular Vortex Generator Pairs to Improve Film Cooling Effectiveness On Transonic Rotor Blade Endwall

2021 ◽  
Author(s):  
Jinjin Li ◽  
Xin Yan ◽  
Kun He ◽  
Richard Goldstein
Keyword(s):  
Film Cooling ◽  
Vortex Generator ◽  
Attack Angle ◽  
Geometrical Parameters ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

Abstract The rectangular vortex generator pairs (RVGPs) are arranged upstream the film cooling holes to achieve a better coolant coverage on endwall near pressure-side corner area. The endwall film cooling effectiveness distributions under transonic flow conditions are numerically calculated for the single RVGP and double rows of RVGPs cases. At first, the effects of three geometrical parameters (i.e. distance between RVGP and cooling hole, height of RVGP and attack angle of RVGP) on endwall film cooling effectiveness are studied with a single hole and RVGP at different mainstream inlet Reynolds numbers and blowing ratios. Then, the double rows of RVGPs are applied to further enhance the overall film cooling effectiveness on blade endwall. The results show that the implementation of RVGPs significantly enhances the film cooling effect on transonic blade endwall at pressure-side corner area. With the increase of RVGP height, the lateral coolant coverage on endwall corner area is improved. However, by decreasing the distance between vortex generator pair and cooling hole, the film cooling effectiveness downstream of the cooling holes is increased. The attack angle of RVGP mainly affects the shape of coolant spreading on endwall surface. The RVGP with optimum dimensions and arrangement is able to suppress the coolant from lifting off the endwall and increase the coolant diffusion near endwall. Compared with no vortex generator case, the area-averaged film cooling effectiveness on endwall with double rows of RVGPs is improved by 13.16%.

Implementation of Vortex Generator and Ramp to Improve Film Cooling Effectiveness on Blade Endwall

2021 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Numerical Methods ◽  
Film Cooling ◽  
Vortex Generator ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Baseline Case ◽  
Cooling Hole ◽  
Cooling Effects ◽  
Endwall Film Cooling

Abstract With the arrangements of vortex generators (VG) and ramp, film cooling effects on endwall near leading edge were numerically investigated at two blowing ratios (i.e. M = 0.5 and M = 1). To determine suitable numerical methods, mesh independency analysis and turbulence model selection were carried out based on the existing experimental data and LES results. With the numerical methods, flow fields near the leading edge were visualized to illustrate the influence of VG and ramp on coolant coverage on blade endwall. Film cooling effectiveness distributions on endwall and coolant trajectories near leading edge were compared among five different configurations with VG and ramp. The results show that the attachment of coolant on blade endwall is improved with the implement of VG between shaped-hole and leading edge. With the implementation of ramp on endwall between cooling hole and leading edge, the coolant spreads wider on endwall along pitchwise direction than the baseline case. With the implementation of VG and ramp, film cooling effect on endwall near leading edge is significantly improved as compared with the only ramp and only VG cases. Compared with the baseline case, pitchwise-averaged film cooling effectiveness on blade endwall near leading edge is increased by about 9%, and the film cooling effectiveness distributions on endwall along pitchwise direction become much uniform, for the case with both ramp and VG at M = 1.

Turbine Blade Platform Film Cooling With Simulated Swirl Purge Flow and Slashface Leakage Conditions

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Andrew F Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Purge Flow ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

The combined effects of inlet purge flow and the slashface leakage flow on the film cooling effectiveness of a turbine blade platform were studied using the pressure-sensitive paint (PSP) technique. Detailed film cooling effectiveness distributions on the endwall were obtained and analyzed. Discrete cylindrical film cooling holes were arranged to achieve an improved coverage on the endwall. Backward injection was attempted by placing backward injection holes near the pressure side leading edge portion. Experiments were done in a five-blade linear cascade with an average turbulence intensity of 10.5%. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. The coolant-to-mainstream mass flow ratios (MFR) were varied from 0.5% and 0.75% to 1% for the purge flow. For the endwall film cooling holes and slashface leakage flow, blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1.0 (close to low temperature experiments) to 1.5 and 2.0 (close to engine conditions) were also examined. The results provide the gas turbine engine designers a better insight into improved film cooling hole configurations as well as various parametric effects on endwall film cooling when the inlet (swirl) purge flow and slashface leakage flow were incorporated.

Computational Predictions of Endwall Film Cooling for a Turbine Nozzle Vane With an Asymmetric Contoured Passage

2008 ◽  
Author(s):  
Yoji Okita ◽  
Chiyuki Nakamata
Keyword(s):  
Film Cooling ◽  
Computational Study ◽  
Suction Side ◽  
Geometrical Parameters ◽  
Passage Vortex ◽  
Rear Part ◽  
Cooling Hole ◽  
Secondary Vortices ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

This paper presents results of a computational study for the endwall film cooling of an annular nozzle cascade employing a circumferentially asymmetric contoured passage. The investigated geometrical parameters and the flow conditions are set consistent with a generic modern HP-turbine nozzle. Rows of cylindrical film cooling holes on the contoured endwall are arranged with a design practice for the ordinary axisymmetric endwall. The solution domain, which includes the mainflow, cooling hole paths, and the coolant plenum, is discretized in the RANS equations with the realizable k-epsilon model. The calculated flow field shows that the pressure gradients across the passage between the pressure and the suction side are reduced with the asymmetric endwall, and consequently, the rolling up of the inlet boundary layer into the passage vortex is delayed and the separation line has moved further downstream. With the asymmetric endwall, because of the effective suppression of the secondary flow, more uniform film coverage is achieved especially in the rear part of the passage and the laterally averaged effectiveness is also significantly improved in this region. The closer inspection of the calculated thermal field reveals that, with the asymmetric passage, the coolant ejected from the holes are less deflected by the secondary vortices, and it attaches better to the endwall in this rear part.

Rib Turbulator Effects on Crossflow-Fed Shaped Film Cooling Holes

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Dale W. Fox ◽  
Fraser B. Jones ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
...  
Keyword(s):  
Film Cooling ◽  
Velocity Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Smooth Channel ◽  
Cooling Hole ◽  
Film Cooling Holes ◽  
Inlet Position ◽  
The Impact

Most studies of turbine airfoil film cooling in laboratory test facilities have used relatively large plenums to feed flow into the coolant holes. However, a more realistic inlet condition for the film cooling holes is a relatively small channel. Previous studies have shown that the film cooling performance is significantly degraded when fed by perpendicular internal crossflow in a smooth channel. In this study, angled rib turbulators were installed in two geometric configurations inside the internal crossflow channel, at 45 deg and 135 deg, to assess the impact on film cooling effectiveness. Film cooling hole inlets were positioned in both prerib and postrib locations to test the effect of hole inlet position on film cooling performance. A test was performed independently varying channel velocity ratio and jet to mainstream velocity ratio. These results were compared to the film cooling performance of previously measured shaped holes fed by a smooth internal channel. The film cooling hole discharge coefficients and channel friction factors were also measured for both rib configurations with varying channel and inlet velocity ratios. Spatially averaged film cooling effectiveness is largely similar to the holes fed by the smooth internal crossflow channel, but hole-to-hole variation due to inlet position was observed.

Turbine Blade Platform Film Cooling With Simulated Swirl Purge Flow and Slashface Leakage Conditions

2016 ◽  
Author(s):  
Andrew F. Chen ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Purge Flow ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

The combined effects of inlet purge flow and the slashface leakage flow on the film cooling effectiveness of a turbine blade platform were studied using the pressure sensitive paint (PSP) technique. Detailed film cooling effectiveness distributions on the endwall were obtained and analyzed. The inlet purge flow was generated by a row of equally-spaced cylindrical injection holes inside a single-tooth generic stator-rotor seal. In addition to the traditional 90 degree (radial outward) injection for the inlet purge flow, injection at a 45 degree angle was adopted to create a circumferential/azimuthal velocity component toward the suction side of the blades, which created a swirl ratio (SR) of 0.6. Discrete cylindrical film cooling holes were arranged to achieve an improved coverage on the endwall. Backward injection was attempted by placing backward injection holes near the pressure side leading edge portion. Slashface leakage flow was simulated by equally-spaced cylindrical injection holes inside a slot. Experiments were done in a five-blade linear cascade with an average turbulence intensity of 10.5%. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. The coolant-to-mainstream mass flow ratios (MFR) were varied from 0.5%, 0.75%, to 1% for the inlet purge flow. For the endwall film cooling holes and slashface leakage flow, blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1.0 (close to low temperature experiments) to 1.5 (intermediate DR) and 2.0 (close to engine conditions) were also examined. The results provide the gas turbine engine designers a better insight into improved film cooling hole configurations as well as various parametric effects on endwall film cooling when the inlet (swirl) purge flow and slashface leakage flow were incorporated.

Influence of Coolant Density on Turbine Blade Film Cooling at Transonic Cascade Flow Conditions Using the Pressure Sensitive Paint Technique

2021 ◽  
Author(s):  
Izhar Ullah ◽  
Sulaiman M. Alsaleem ◽  
Lesley M. Wright ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Blade Tip ◽  
Film Cooling Holes

Abstract This work is an experimental study of film cooling effectiveness on a blade tip in a stationary, linear cascade. The cascade is mounted in a blowdown facility with controlled inlet and exit Mach numbers of 0.29 and 0.75, respectively. The free stream turbulence intensity is measured to be 13.5 % upstream of the blade’s leading edge. A flat tip design is studied, having a tip gap of 1.6%. The blade tip is designed to have 15 shaped film cooling holes along the near-tip pressure side (PS) surface. Fifteen vertical film cooling holes are placed on the tip near the pressure side. The cooling holes are divided into a 2-zone plenum to locally maintain the desired blowing ratios based on the external pressure field. Two coolant injection scenarios are considered by injecting coolant through the tip holes only and both tip and PS surface holes together. The blowing ratio (M) and density ratio (DR) effects are studied by testing at blowing ratios of 0.5, 1.0, and 1.5 and three density ratios of 1.0, 1.5, and 2.0. Three different foreign gases are used to create density ratio effect. Over-tip flow leakage is also studied by measuring the static pressure distributions on the blade tip using the pressure sensitive paint (PSP) measurement technique. In addition, detailed film cooling effectiveness is acquired to quantify the parametric effect of blowing ratio and density ratio on a plane tip design. Increasing the blowing ratio and density ratio resulted in increased film cooling effectiveness at all injection scenarios. Injecting coolant on the PS and the tip surface also resulted in reduced leakage over the tip. The conclusions from this study will provide the gas turbine designer with additional insight on controlling different parameters and strategically placing the holes during the design process.

Design of Full-Scale Endwall Film Cooling of a Turbine Vane

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Jian Liu ◽  
Wei Du ◽  
Guohua Zhang ◽  
Safeer Hussain ◽  
Lei Wang ◽  
...  
Keyword(s):  
High Temperature ◽  
Film Cooling ◽  
Pressure Coefficient ◽  
Pressure Side ◽  
Junction Region ◽  
Film Cooling Effectiveness ◽  
Coefficient Distribution ◽  
Turbine Vane ◽  
Endwall Film Cooling ◽  
Film Cooling Holes

Abstract Endwall film cooling is a significant cooling method to protect the endwall region and the junction region of endwall and a turbine vane, where usually a relatively high temperature load exists. This work aims to find the optimized arrangement of film cooling holes on the endwall and improve the film cooling in some difficult regions on the endwall, such as pressure side-endwall junction region. Several ideas for film cooling hole arrangement design are proposed, based on the pressure coefficient distribution, the streamline distribution, and the heat transfer coefficient (HTC) distribution, respectively. Four specified designs are built and compared. The results are obtained by numerical calculations with a well-validated turbulence model, the k–ω shear stress transport (SST) model. From this work, the designs based on the pressure coefficient distribution (designs 1 and 2) force the flow from the pressure side to the suction side (SS), especially in design 2, which adopts compound angle holes. The designs based on pressure coefficients have benefit in the cooling of the SS but give worse coolant coverage on the pressure side. In addition, designs 1 and 2 have little influence on the original pressure field. The design based on the streamline distributions (design 3) has larger coolant coverage on the endwall and provides good coolant coverage on the endwall and pressure side junction region. The design based on the HTC distribution provides large overall film cooling effectiveness on both the pressure side and the SS. More film cooling holes are placed on the high temperature regions, which is more effective in practice.

Film Cooling Measurements for a Laidback Fan-Shaped Hole: Effect of Coolant Crossflow on Cooling Effectiveness and Heat Transfer

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Marc Fraas ◽  
Tobias Glasenapp ◽  
Achmed Schulz ◽  
Hans-Jörg Bauer
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Film Cooling ◽  
Gas Flow ◽  
Density Ratio ◽  
Coolant Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Film Cooling Holes

Internal coolant passages of gas turbine vanes and blades have various orientations relative to the external hot gas flow. As a consequence, the inflow of film cooling holes varies as well. To further identify the influencing parameters of film cooling under varying inflow conditions, the present paper provides detailed experimental data. The generic study is performed in a novel test rig, which enables compliance with all relevant similarity parameters including density ratio. Film cooling effectiveness as well as heat transfer of a 10–10–10 deg laidback fan-shaped cooling hole is discussed. Data are processed and presented over 50 hole diameters downstream of the cooling hole exit. First, the parallel coolant flow setup is discussed. Subsequently, it is compared to a perpendicular coolant flow setup at a moderate coolant channel Reynolds number. For the perpendicular coolant flow, asymmetric flow separation in the diffuser occurs and leads to a reduction of film cooling effectiveness. For a higher coolant channel Reynolds number and perpendicular coolant flow, asymmetry increases and cooling effectiveness is further decreased. An increase in blowing ratio does not lead to a significant increase in cooling effectiveness. For all cases investigated, heat transfer augmentation due to film cooling is observed. Heat transfer is highest in the near-hole region and decreases further downstream. Results prove that coolant flow orientation has a severe impact on both parameters.

Geometrical Optimization and Experimental Validation of a Tripod Film Cooling Hole With Asymmetric Side Holes

2014 ◽  
Author(s):  
Zhongran Chi ◽  
Chang Han ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Experimental Results ◽  
Geometrical Parameters ◽  
Vortex System ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Optimum Configuration ◽  
Optimization Study ◽  
Cooling Hole

A tripod cylindrical film hole with asymmetric side holes is studied numerically and experimentally on a flat plate for higher film cooling effectiveness. Firstly, the influences of geometrical parameters are studied and the optimum configurations of the asymmetric tripod hole are found in a DoE optimization study based on an improved numerical model for film cooling prediction, in which more than one hundred 3D CFD simulations are carried out. Then one optimum configuration of the asymmetric tripod hole is examined experimentally using pressure-sensitive paint (PSP) measurements, and compared against the experimental results of the simple cylindrical film hole and a well-designed shaped film hole. The flow and heat transfer characteristics of the asymmetric tripod holes were explored from the DoE results. The side holes can form a shear vortex system or an anti-kidney vortex system when proper spanwise distances of them are adopted, which laterally transports the coolant and form a favorable coolant coverage. According to the experimental results, the cooling performance of the optimized asymmetric tripod hole is significantly better than that of the simple cylindrical hole, especially at high blowing ratios. And the optimized asymmetric tripod hole can provide almost the same or even higher film cooling effectiveness on the flat plate compared with the shaped hole in the same flow conditions.

Enhanced Film Cooling Effectiveness With Surface Trenches

2013 ◽  
Author(s):  
K. Vighneswara Rao ◽  
Jong S. Liu ◽  
Daniel C. Crites ◽  
Luis A. Tapia ◽  
Malak F. Malak ◽  
...  
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Operating Conditions ◽  
Airfoil Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Ansys Cfx ◽  
Cooling Hole ◽  
Computational Fluid Dynamics Cfd ◽  
Film Cooling Holes

In this study, cylindrical and fan shaped film cooling holes are evaluated on the blade surface numerically, using the Computational Fluid Dynamics (CFD) tool ANSYS-CFX, with the objective of improving cooling effectiveness by understanding the flow pattern at the cooling hole exit. The coolant flow rates are adjusted for blowing ratios of 0.5, 1.0 & 1.5 (momentum flux ratios of 0.125, 0.5 & 1.125 respectively). The density ratio is maintained at 2.0. New shaped holes viz. straight, concave and convex trench holes are introduced and are evaluated under similar operating conditions. Results are presented in terms of surface temperatures and adiabatic effectiveness at three different blowing ratios for the different film cooling hole shapes analyzed. Comparison is made with reference to the fan shaped film cooling hole to bring out relative merits of different shapes. The new trench holes improved the film cooling effectiveness by allowing more residence time for coolant to spread laterally while directing smoothly onto the airfoil surface. While convex trench improved the centre-line effectiveness, straight trench improved the laterally-averaged and overall effectiveness at all blowing ratios. Concave trench improved the effectiveness at blowing ratios 0.5 and 1.0.

Sign in / Sign up

Export Citation Format

Share Document