scholarly journals Modeling of Tip Clearance Flows Through an Improved 3-D Pressure Correction Navier-Stokes Solver

1993 ◽  
Author(s):  
N. Lymberopoulos ◽  
K. Giannakoglou ◽  
I. Nikolaou ◽  
K. D. Papailiou ◽  
A. Tourlidakis ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Special Treatment ◽  
Pressure Correction ◽  
Compressor Rotor ◽  
Numerical Predictions ◽  
Correction Technique

Mechanical constraints dictate the existence of tip clearances in rotating cascades, resulting to a flow leakage through this clearance which considerably influences the efficiency and range of operation of the machine. Three-dimensional Navier-Stokes solvers are often used for the numerical study of compressor and turbine stages with tip-clearance. The quality of numerical predictions depends strongly on how accurately the blade tip region is modelled; in this respect the accurate modelling of tip region was one of the main goals of this work. In the present paper, a 3-D Navier-Stokes solver is suitably adapted so that the flat tip surface of a blade and its sharp edges could be accurately modelled, in order to improve the precision of the calculation in the tip region. The adapted code solves the fully elliptic, steady, Navier-Stokes equations through a space-marching algorithm and a pressure correction technique; the H-type topology is retained, even in cases with thick leading edges where a special treatment is introduced herein. The analysis is applied to two different cases, a linear cascade and a compressor rotor, and comparisons with experimental data are provided.

Numerical Study of the Tip Clearance Flow Development in a Propulsion Pump Stage

1996 ◽  
Author(s):  
Yu-Tai Lee ◽  
Chunill Hah ◽  
James Loellbach
Keyword(s):  
Vortex Structure ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Navier Stokes ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
High Reynolds

This paper summarizes a numerical investigation of the fundamental structure of the rotor tip-clearance vortex and its interaction with a passage trailing-edge vortex in a single-stage stator-rotor pump. The flow field of a highly-loaded rotor measured in a high Reynolds number pump facility (HIREP) is used for comparison. The numerical solution was obtained by solving the three-dimensional Reynolds averaged Navier-Stokes equations. The calculated results are visualized in order to understand the details of the tip-vortex structure. The study shows that the tip geometry should be accurately represented to predict the tip-vortex structure correctly.

Numerical Study of the Pulsating Flow at the Tongue Region of a Centrifugal Pump for Several Flow Rates

2008 ◽  
Author(s):  
Rau´l Barrio ◽  
Jorge Parrondo ◽  
Eduardo Blanco ◽  
Joaqui´n Ferna´ndez
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Numerical Predictions ◽  
Partial Load ◽  
Flow Through

A numerical study is presented on the unsteady flow at the tongue region of a single suction volute-type centrifugal pump with a specific speed of 0.46. The flow through the pump, available at laboratory, was simulated by means of a commercial CFD software that solved the Reynolds averaged Navier-Stokes equations for three-dimensional unsteady flow (3D-URANS). A sensitivity analysis of the numerical model was carried out and the numerical predictions were compared with previous experimental results of both global and unsteady variables. Once validated, the model was used to study the flow pulsations associated to the interaction between the impeller blades and the volute tongue as a function of the flow rate, from partial load to overload. The study allowed relating the passage of the impeller blades with the tangential and radial velocity pulsations at some reference positions and with the pressure pulsations at the tongue region.

A Numerical Analysis of the Three-Dimensional Viscous Flow in a Transonic Compressor Rotor and Comparison With Experiment

1987 ◽  
Vol 109 (1) ◽  
pp. 83-90 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Boundary Layer ◽  
Numerical Analysis ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Viscous Effects ◽  
Transonic Compressor ◽  
Compressor Rotor

The numerical analysis of highly loaded transonic compressors continues to be of considerable interest. Although much progress has been made with inviscid analyses, viscous effects can be very significant, especially those associated with shock–boundary layer interactions. While inviscid analyses have been enhanced by the interactive inclusion of blade surf ace boundary layer calculations, it may be better in the long term to develop efficient algorithms to solve the full three-dimensional Navier–Stokes equations. Indeed, it seems that many phenomena of key interest, like tip clearance flows, may only be accessible to a Navier–Stokes solver. The present paper describes a computer program developed for solving the three-dimensional viscous compressible flow equations in turbomachine geometries. The code is applied to the study of the flowfield in an axial-flow transonic compressor rotor with an attempt to resolve the tip clearance flow. The predicted flow is compared with laser anemometry measurements and good agreement is found.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

scholarly journals Choice and Limits of a Fluid Model for the Numerical Study in Dynamic Fluid Structure Interaction Problems

2003 ◽  
Author(s):  
Jean Franc¸ois Sigrist ◽  
Christian Laine ◽  
Dominique Lemoine ◽  
Bernard Peseux
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Model ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Linear Solution ◽  
Fluid Structure ◽  
Design Engineers ◽  
Inviscid Incompressible Fluid ◽  
Basic Fluid

This paper is related to the study of a nuclear propulsion reactor prototype for the French Navy. This prototype is built on ground and is to be dimensioned toward seismic loading. The dynamic analysis takes the coupled fluid structure analysis into account. The basic fluid models used by design engineers are inviscid incompressible or compressible. The fluid can be described in a bidimensional by slice or a three-dimensional approach. A numerical study is carried out on a generic problem for the linear FSI dynamic problem. The results of this study are presented and discussed. As a conclusion, the three-dimensional inviscid incompressible fluid appears to be the best compromise between the description of physical phenomena and the cost of modeling. The geometry of the reactor is such that large displacements of the structure in the fluid can occur. Therefore, the linearity hypothesis might not be longer valid. The case of large amplitude imposed oscillating motion of a cylinder in a confined fluid is numerically studied. A CFD code is used to investigate the fluid behavior solving the NAVIER-STOKES equations. The forces induced on the cylinder by the fluid are computed and compared to the linear solution. The limit of the linear model can then be exhibited.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

scholarly journals Numerical Study on the Solid Fuel Rocket Scramjet Combustor with Cavity

Energies ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1235 ◽  
Author(s):  
Chaolong Li ◽  
Zhixun Xia ◽  
Likun Ma ◽  
Xiang Zhao ◽  
Binbin Chen
Keyword(s):  
Solid Fuel ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Combustion Efficiency ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Particle Combustion ◽  
Scramjet Combustor ◽  
Cavity Configuration

Scramjet based on solid propellant is a good supplement for the power device of future hypersonic vehicles. A new scramjet combustor configuration using solid fuel, namely, the solid fuel rocket scramjet (SFRSCRJ) combustor is proposed. The numerical study was conducted to simulate a flight environment of Mach 6 at a 25 km altitude. Three-dimensional Reynolds-averaged Navier–Stokes equations coupled with shear stress transport (SST) k − ω turbulence model are used to analyze the effects of the cavity and its position on the combustor. The feasibility of the SFRSCRJ combustor with cavity is demonstrated based on the validation of the numerical method. Results show that the scramjet combustor configuration with a backward-facing step can resist high pressure generated by the combustion in the supersonic combustor. The total combustion efficiency of the SFRSCRJ combustor mainly depends on the combustion of particles in the fuel-rich gas. A proper combustion organization can promote particle combustion and improve the total combustion efficiency. Among the four configurations considered, the combustion efficiency of the mid-cavity configuration is the highest, up to about 70%. Therefore, the cavity can effectively increase the combustion efficiency of the SFRSCRJ combustor.

scholarly journals Numerical Study of the Internal Flow Field of a Centrifugal Impeller

1994 ◽  
Author(s):  
Mou-jin Zhang ◽  
Chuan-gang Gu ◽  
Yong-miao Miao
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Internal Flow ◽  
Staggered Grid ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
High Reynolds

The complex three-dimensional flow field in a centrifugal impeller with low speed is studied in this paper. Coupled with high–Reynolds–number k–ε turbulence model, the fully three–dimensional Reynolds averaged Navier–Stokes equations are solved. The Semi–Implicit Method for Pressure–Linked Equations (SIMPLE) algorithm is used. And the non–staggered grid arrangement is also used. The computed results are compared with the available experimental data. The comparison shows good agreement.

Sign in / Sign up

Export Citation Format

Share Document