scholarly journals Convective Heat Transfer Enhancement in Nanofluids: Real Anomaly or Analysis Artifact?

2011 ◽  
Author(s):  
Naveen Prabhat ◽  
Jacopo Buongiorno ◽  
Lin-wen Hu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Temperature Dependence ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Convective Heat ◽  
Transfer Enhancement

The nanofluid literature contains many claims of anomalous convective heat transfer enhancement in both turbulent and laminar flow. To put such claims to the test, we have performed a critical detailed analysis of the database reported in 12 nanofluid papers (8 on laminar flow and 4 on turbulent flow). The methodology accounted for both modeling and experimental uncertainties in the following way. The heat transfer coefficient for any given data set was calculated according to the established correlations (Dittus-Boelter’s for turbulent flow and Shah’s for laminar flow). The uncertainty in the correlation input parameters (i.e. nanofluid thermo-physical properties and flow rate) was propagated to get the uncertainty on the predicted heat transfer coefficient. The predicted and measured heat transfer coefficient values were then compared to each other. If they differed by more than their respective uncertainties, we judged the deviation anomalous. According to this methodology, it was found that in nanofluid laminar flow in fact there seems to be anomalous heat transfer enhancement in the entrance region, while the data are in agreement (within uncertainties) with the Shah’s correlation in the fully developed region. On the other hand, the turbulent flow data could be reconciled (within uncertainties) with the Dittus-Boelter’s correlation, once the temperature dependence of viscosity was included in the prediction of the Reynolds number. While this finding is plausible, it could not be conclusively confirmed, because most papers do not report information about the temperature dependence of the viscosity for their nanofluids.

Heat Transfer Enhancement in Split and Recombine Flow Configurations: A Numerical and Experimental Study

2016 ◽  
Author(s):  
Mojtaba Jarrahi ◽  
Jean-Pierre Thermeau ◽  
Hassan Peerhossaini
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Convective Heat ◽  
Convective Heat Transfer Coefficient ◽  
Working Fluid ◽  
Transfer Enhancement

Heat transfer enhancement in laminar regime by split and recombine (SAR) mechanism, based on the baker’s transformation, is investigated. Two different heat exchangers, called SAR1 and SAR2, are studied. Their geometries are inspired from the previous studies reported in the literature. The working fluid on both, shell and tube side, is water and the temperature on the shell side is kept constant. Experiments are carried out for the Reynolds number range 100<Re<3000 when the Prandtl number is between 4.5 and 7.5. The results show that the convective heat transfer coefficient in the first element of heat exchanger SAR1 is higher than that in the second one, i.e. SAR2. However, the variation in the convective heat transfer coefficient from the first to the third element along the heat exchanger SAR2 is less significant than that observed for SAR1. Moreover, SAR2 causes a higher pressure drop, especially when Re>1000, and provides a less uniform temperature field at the outlet.

Convective Heat Transfer Characteristics of Silver-Water Nanofluid Under Laminar and Turbulent Flow Conditions

2012 ◽  
Vol 4 (3) ◽  
Author(s):  
Lazarus Godson ◽  
B. Raja ◽  
D. Mohan Lal ◽  
S. Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Pure Water ◽  
Convective Heat Transfer Coefficient ◽  
Experimental Results

The convective heat transfer coefficient and pressure drop of silver-water nanofluids is measured in a counter flow heat exchanger from laminar to turbulent flow regime. The experimental results show that the convective heat transfer coefficient of the nanofluids increases by up to 69% at a concentration of 0.9 vol. % compared with that of pure water. Furthermore, the experimental results show that the convective heat transfer coefficient enhancement exceeds the thermal conductivity enhancement. It is observed that the measured heat transfer coefficient is higher than that of the predicted ones using Gnielinski equation by at least 40%. The use of the silver nanofluid has a little penalty in pressure drop up to 55% increase 0.9% volume concentration of silver nanoparticles.

scholarly journals NUMERICAL STUDY OF THERMAL CHARACTERISTICS OF FUEL OIL-ALUMINA AND WATER-ALUMINA NANOFLUIDS FLOW IN A CHANNEL IN THE LAMINAR FLOW

2018 ◽  
Vol 19 (1) ◽  
pp. 251-269 ◽  
Author(s):  
Hossein Fatahian ◽  
Hesamoddin Salarian ◽  
Majid Eshagh Nimvari ◽  
Esmaeel Fatahian
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Fuel Oil ◽  
Alumina Nanofluid

The present study investigated the thermal effects of the use of nanoparticles in the fuel-oil and water-based fluids, as well as the numerical simulation of laminar flow of fuel-oil-alumina and the water-alumina nanofluids in a channel. A second order discretization method was used for solving equations and a SIMPLE algorithm was applied for pressure-velocity coupling using Fluent. Effect of nanoparticle volume fraction and particles size in different Reynolds numbers (900≤Re≤2100) on the convective heat transfer coefficient was studied. The simulation was conducted for three different volume fractions and particle sizes in the laminar flow under constant heat flux. The results showed that adding nanoparticles to the base fluid caused an increase in the thermal conductivity ratio of the fluid, which was observed to a greater degree in the fuel oil-alumina nanofluid than in the water-alumina nanofluid. The increase in nanoparticle volume fraction caused an increase in the convective heat transfer coefficient and the Nusselt number of the nanofluids. The significant point of this study was that in the same volume fraction, the effect of adding alumina nanoparticles to the fuel-oil-based fluid had more effect than adding these particles to water-based fluid, while the effect of increasing the Reynolds number in the water-alumina nanofluid on convective heat transfer coefficient was greater than the fuel-oil-alumina. Also, in the same Reynolds number and volume fraction with increasing size of nanoparticles, the value of the convective heat transfer coefficient was decreased. The results of this study can be used in refineries and petrochemical industries where the fuel-oil fluid flows in the channels. ABSTRAK: Kajian ini adalah bagi mengkaji kesan haba terhadap penggunaan bahan bakar-minyak dan cecair asas-air dalam nanopartikel, juga menjalankan simulasi pengiraan aliran laminar bahan bakar-minyak-alumina dan cecair-nano air-alumina dalam saluran. Kaedah berasingan kelas kedua telah digunakan bagi menyelesaikan persamaan dan algoritma SIMPLE telah diaplikasikan dalam gandingan kelajuan-tekanan menggunakan Fluent. Kesan jumlah pecahan nanopartikel dan pelbagai bilangan saiz zarah dalam bilangan Reynolds (900≤Re≤2100) pada pekali pemindahan haba perolakan telah dikaji. Simulasi telah dijalankan pada tiga pecahan isipadu berlainan dan pada zarah dalam aliran laminar dengan fluks haba tetap. Hasil kajian menunjukkan bahawa dengan penambahan nanopartikel dalam cecair-asas menyebabkan peningkatan nisbah daya pengaliran haba cecair pada cecair-nano bahan bakar-minyak-alumina melebihi daripada cecair-nano air-alumina. Penambahan pada pecahan isipadu nanopartikel ini menyebabkan peningkatan pada nilai pekali pemindahan haba perolakan dan bilangan Nusselt dalam cecair-nano. Perkara penting dalam kajian ini adalah pada pecahan isipadu sama, kesan penambahan nanopartikel alumina kepada cecair berasaskan minyak mempunyai kesan yang lebih besar daripada penambahan zarah-zarah ini kepada cecair berasaskan air. Pada masa sama, kesan peningkatan bilangan Reynolds dalam cecair-nano air-alumina pada pekali pemindahan haba perolakan lebih besar daripada kesan peningkatan bahan bakar-minyak-alumina. Selain itu, pada bilangan Reynolds yang sama dan dengan peningkatan saiz nanopartikel pecahan isipadu, nilai pekali pemindahan haba perolakan turut menurun. Hasil kajian ini boleh digunakan dalam industri penapisan dan petrokimia di mana bahan bakar cecair minyak mengalir dalam saluran.

Applied Pulsed Flow for Single-Phase Convective Heat Transfer Enhancement in a Laminar Flow Cooling System

2008 ◽  
Author(s):  
Bolaji O. Olayiwola ◽  
Gerhard Schaldach ◽  
Peter Walzel
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Cooling System ◽  
Transfer Enhancement ◽  
Flow Rates ◽  
The Heat Transfer Coefficient

Experimental and CFD studies were performed to investigate the enhancement of convective heat transfer in a laminar cooling system using flow pulsation in a flat channel with series of regular spaced fins. Glycerol-water mixtures with dynamic viscosities in the range of 0.001 kg/ms–0.01 kg/ms were used. A steady flow Reynolds number in the laminar range of 10 &lt; Re &lt; 1200 was studied. The amplitudes of the applied pulsations are in the range of 0.25 &lt; A &lt; 0.55 mm and the frequency range is 10 &lt; f &lt; 60 Hz. Two different cooling devices with active length L = 450 mm and 900 mm were investigated. CFD simulations were performed on a parallel-computer (Linux-cluster) using the software suit CFX11 from ANSYS GmbH, Germany. The rate of cooling was found to be significant at moderate low net flow rates. In general, no significant heat transfer enhancement at very low and high flow rates was obtained in compliance with the experimental data. The heat transfer coefficient was found to increase with increasing Prandtl number Pr at constant oscillation Reynolds number Reosc whereas the ratio of the hydraulic diameter to the length of the channel dh/L has insignificant effect on the heat transfer coefficient. This is due to enhanced fluid mixing. CFD results allow for performance predictions of different geometries and flow conditions.

Demonstration of Heat Transfer Enhancement Using Ferromagnetic Particle Laden Fluid and Switched Magnetic Fields

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Mark M. Murray
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Pipe Wall ◽  
Differential Pressure ◽  
Transfer Enhancement ◽  
Enhancement Technique ◽  
Ferromagnetic Particles

A convective heat transfer enhancement technique and the experimental methods used to quantify the improvement in heat transfer and subsequent differential pressure are introduced. The enhancement technique employed time varying magnetic fields produced in a pipe to cause the ferromagnetic particles of a particle laden fluid (mineral oil and iron filings) to be attracted to and released from a heated pipe wall. The ferromagnetic particles acted not only to advect heat from the pipe wall into the bulk fluid but they also significantly modified the flow field, disrupted the boundary layer, allowed cooler fluid to reach the high temperature pipe wall, increased thermal energy transfer directly to the fluid, and contributed to the overall improvement in heat transfer rate. The experimental method utilized to quantify an increased effectiveness of convective heat transfer used an apparatus designed to replicate an internally cooled fin, whose surface temperature was measured with an IR camera. These temperature measurements were utilized to calculate the convective heat transfer coefficient (h) of the fluid within the pipe. The enhancement technique demonstrated a 267% increase in heat transfer coefficient with only a corresponding 48% increase in flow differential pressure for an electromagnetic switching frequency of 2 Hz. It is also found that there were optimum magnetic field switching frequencies for both enhancement and differential pressure magnitudes.

Forced Convective Heat Transfer of Nanofluids in Microchannels

2006 ◽  
Author(s):  
Jung-Yeul Jung ◽  
Hoo-Suk Oh ◽  
Ho-Young Kwak
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Flow Regime ◽  
Convective Heat ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Laminar Flow Regime

Convective heat transfer coefficient and friction factor of a nanofluid in rectangular microchannel were measured. An integrated microsystem consisting of a single microchannel on one side and two localized heaters and five polysilicon temperature sensors along the channel on the other side were fabricated. Aluminum dioxide (Al2O3) nanofluids with various particle volume fractions were used in experiment to investigate the effect of the volume fraction of the nanoparticles to the convective heat transfer and fluid flow in microchannels. The convective heat transfer coefficient of the Al2O3 nanofluid in laminar flow regime was measured to be increased up to 15% compared to the distilled water at a volume fraction of 1.8 volume percent without major friction loss. The Nusselt number measured increases with increasing the Reynolds number in laminar flow regime. A new type of convective heat transfer correlation was proposed to correlate experimental data of heat transfer coefficient for nanofluids in microchannels.

Sign in / Sign up

Export Citation Format

Share Document