On the Direct Kinematics of a Class of Spherical Three-Degree-of Freedom Parallel Manipulators

1992 ◽  
Author(s):  
Clément M. Gosselin ◽  
Jaouad Sefrioui ◽  
Marc J. Richard
Keyword(s):  
Parallel Manipulator ◽  
Minimal Polynomial ◽  
Polynomial Solution ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Real Solutions ◽  
Revolute Joints ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator ◽  
Direct Kinematics

Abstract This paper presents a polynomial solution to the direct kinematic problem of a class of spherical three-degree-of-freedom parallel manipulators. This class is defined as the set of manipulators for which the axes of the three revolute joints attached to the gripper link are coplanar and symmetrically arranged. It is shown that, for these manipulators, the direct kinematic problem admits a maximum of 8 real solutions. A polynomial of degree 8 is obtained here to support this result and cases for which all the roots of the polynomial lead to real configurations are presented. Finally, the spherical parallel manipulator with collinear actuators, which received some attention in the literature, is also treated and is shown to lead to a minimal polynomial of the same degree. Examples of the application of the method to manipulators of each category are given and solved.

On the Direct Kinematics of Spherical Three-Degree-of-Freedom Parallel Manipulators with a Coplanar Platform

1994 ◽  
Vol 116 (2) ◽  
pp. 587-593 ◽  
Author(s):  
C. M. Gosselin ◽  
J. Sefrioui ◽  
M. J. Richard
Keyword(s):  
Parallel Manipulator ◽  
Minimal Polynomial ◽  
Polynomial Solution ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Real Solutions ◽  
Revolute Joints ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator ◽  
Direct Kinematics

This paper presents a polynomial solution to the direct kinematic problem of a class of spherical three-degree-of-freedom parallel manipulators. This class is defined as the set of manipulators for which the axes of the three revolute joints attached to the gripper link are coplanar and symmetrically arranged. It is shown that, for these manipulators, the direct kinematic problem admits a maximum of 8 real solutions. A polynomial of degree 8 is obtained here to support this result and cases for which all the roots of the polynomial lead to real configurations are presented. Finally, the spherical parallel manipulator with collinear actuators, which received some attention in the literature, is also treated and is shown to lead to a minimal polynomial of the same degree. Examples of the application of the method to manipulators of each category are given and solved.

On the Direct Kinematics of Spherical Three-Degree-of-Freedom Parallel Manipulators of General Architecture

1994 ◽  
Vol 116 (2) ◽  
pp. 594-598 ◽  
Author(s):  
C. M. Gosselin ◽  
J. Sefrioui ◽  
M. J. Richard
Keyword(s):  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Real Solutions ◽  
Three Degree Of Freedom ◽  
General Architecture ◽  
Direct Kinematics

In this paper, the direct kinematics of general spherical parallel three-degree-of-freedom manipulators is investigated. A polynomial of degree 8 is obtained to describe this problem and it is shown that this polynomial is minimal since 8 real solutions corresponding to actual configurations have been found for a given set of actuator coordinates and a given architecture. This result completes the study on the direct kinematics of spherical three-degree-of-freedom parallel manipulators undertaken by the authors in a previous paper. An example of an architecture and a set of actuator coordinates which lead to 8 real solutions is presented to illustrate the results.

Analysis of Two Spherical Parallel Manipulators With Hidden Revolute Joints

2017 ◽  
Vol 9 (3) ◽  
Author(s):  
Ju Li ◽  
J. Michael McCarthy
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Internal Constraints ◽  
Quadric Surfaces ◽  
Revolute Joints ◽  
Serial Chain ◽  
Point Of Intersection ◽  
Spherical Parallel Manipulator

In this paper, we examine two spherical parallel manipulators (SPMs) constructed with legs that include planar and spherical subchains that combine to impose constraints equivalent to hidden revolute joints. The first has supporting serial chain legs constructed from three revolute joints with parallel axes, denoted R∥R∥R, followed by two revolute joints that have intersecting axes, denoted RR̂. The leg has five degrees-of-freedom and is denoted R∥R∥R-RR̂. Three of these legs can be assembled so the spherical chains all share the same point of intersection to obtain a spherical parallel manipulator denoted as 3-R∥R∥R-RR̂. The second spherical parallel manipulator has legs constructed from three revolute joints that share one point of intersection, denoted RRR̂, and a second pair of revolute joints with axes that intersect in a different point. This five-degree-of-freedom leg is denoted RRR̂-RR̂. The spherical parallel manipulator constructed from these legs is 3-RRR̂-RR̂. We show that the internal constraints of these two types of legs combine to create hidden revolute joints that can be used to analyze the kinematics and singularities of these spherical parallel manipulators. A quaternion formulation provides equations for the quartic singularity varieties some of which decompose into pairs of quadric surfaces which we use to classify these spherical parallel manipulators.

On the Direct Kinematics of General Spherical Three-Degree-of-Freedom Parallel Manipulators

1992 ◽  
Author(s):  
Clément M. Gosselin ◽  
Jaouad Sefrioui ◽  
Marc J. Richard
Keyword(s):  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Real Solutions ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Abstract In this paper, the direct kinematics of general spherical parallel three-degree-of-freedom manipulators is investigated. A polynomial of degree 8 is obtained to describe this problem and it is shown that this polynomial is minimal since 8 real solutions corresponding to actual configurations have been found for a given set of actuator coordinates and a given architecture. This result completes the study on the direct kinematics of spherical three-degre-of-freedom parallel manipulators undertaken by the authors in a previous paper. An example of an architecture and a set of actuator coordinates which lead to 8 real solutions is presented to illustrate the results.

Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator

2006 ◽  
Vol 129 (3) ◽  
pp. 320-325 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three-degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three-DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base mounted, higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of the tangent of the half-angle between one of the limbs and the base plane. Hence, there are at most 16 assembly configurations for the manipulator. In addition, it is shown that the 16 solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

Parametric Design of a Spherical Eight-Bar Linkage Based on a Spherical Parallel Manipulator

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Parametric Design ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Arbitrary Base ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a procedure that determines the dimensions of two constraining links to be added to a three degree-of-freedom spherical parallel manipulator so that it becomes a one degree-of-freedom spherical (8, 10) eight-bar linkage that guides its end-effector through five task poses. The dimensions of the spherical parallel manipulator are unconstrained, which provides the freedom to specify arbitrary base attachment points as well as the opportunity to shape the overall movement of the linkage. Inverse kinematics analysis of the spherical parallel manipulator provides a set of relative poses between all of the links, which are used to formulate the synthesis equations for spherical RR chains connecting any two of these links. The analysis of the resulting spherical eight-bar linkage verifies the movement of the system.

A new closed-form kinematics of the generalized 3-DOF spherical parallel manipulator

Robotica ◽  
1999 ◽  
Vol 17 (5) ◽  
pp. 475-485 ◽  
Author(s):  
Zhen Huang ◽  
Y. Lawrence Yao
Keyword(s):  
Closed Form ◽  
Analytical Method ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
New Method ◽  
Numerical Example ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a new method to analyze the closed-form kinematics of a generalized three-degree-of-a-freedom spherical parallel manipulator. Using this analytical method, concise and uniform solutions are achieved. Two special forms of the three-degree-of-freedom spherical parallel manipulator, i.e. right-angle type and a decoupled type, are also studied and their unique and interesting properties are investigated, followed by a numerical example.

Kinematics of a New High Precision Three Degree-of-Freedom Parallel Manipulator

2005 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base-mounted; higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of tangent of half-angle between one of the limbs and the base plane. Hence, there are at most sixteen assembly configurations for the manipulator. In addition, it is shown that the sixteen solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

scholarly journals A Parallel Manipulator With Only Translational Degrees of Freedom

1996 ◽  
Author(s):  
Lung-Wen Tsai ◽  
Richard Stamper
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Translational Motion ◽  
Forward Kinematics ◽  
Closed Form Solutions ◽  
Real Solutions ◽  
Revolute Joints ◽  
Inverse Kinematics Problem ◽  
Three Degree Of Freedom

Abstract This paper presents a novel three degree of freedom parallel manipulator that employs only revolute joints and constrains the manipulator output to translational motion. Closed-form solutions are developed for both the inverse and forward kinematics. It is shown that the inverse kinematics problem has up to four real solutions, and the forward kinematics problem has up to 16 real solutions.

Parallel Computational Algorithms for the Kinematics and Dynamics of Planar and Spatial Parallel Manipulators

1996 ◽  
Vol 118 (1) ◽  
pp. 22-28 ◽  
Author(s):  
C. M. Gosselin
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Inverse Dynamics ◽  
Parallel Manipulators ◽  
Degree Of Freedom ◽  
Kinematic Chains ◽  
Novel Approach ◽  
Judicious Choice ◽  
Six Degree Of Freedom ◽  
Three Degree Of Freedom

This paper introduces a novel approach for the computation of the inverse dynamics of parallel manipulators. It is shown that, for this type of manipulator, the inverse kinematics and the inverse dynamics procedures can be easily parallelized. The result is a closed-form efficient algorithm using n processors, where n is the number of kinematic chains connecting the base to the end-effector. The dynamics computations are based on the Newton-Euler formalism. The parallel algorithm arises from a judicious choice of the coordinate frames attached to each of the legs, which allows the exploitation of the parallel nature of the mechanism itself. Examples of the application of the algorithm to a planar three-degree-of-freedom parallel manipulator and to a spatial six-degree-of-freedom parallel manipulator are presented.

Sign in / Sign up

Export Citation Format

Share Document