Criteria for Spike Initiated Rotating Stall

2005 ◽  
Author(s):  
Huu Duc Vo ◽  
Choon S. Tan ◽  
Edward M. Greitzer
Keyword(s):  
Computational Study ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Length Scale ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Circumferential Extent

A computational study to define the phenomena that lead to the onset of short length-scale (spike) rotating stall disturbances has been carried out. Unsteady simulations show there are two conditions necessary for the formation of spike disturbances, both of which are linked to the tip clearance flow. One is that the interface between the tip clearance and oncoming flows becomes parallel to the leading edge plane. The second is the initiation of backflow, stemming from the fluid in adjacent passages, at the trailing edge plane. The two criteria also imply a length scale circumferential extent of spike disturbances. The scenario developed is consistent with numerical simulations as well as with experimental observations of axial compressor stall inception. A comparison of calculations for multiple blades with those for single passages also allows statements to be made about the utility of single passage computations as a descriptor of compressor stall.

Criteria for Spike Initiated Rotating Stall

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Huu Duc Vo ◽  
Choon S. Tan ◽  
Edward M. Greitzer
Keyword(s):  
Computational Study ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotating Stall ◽  
Short Length ◽  
Tip Clearance ◽  
Length Scale ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow

A computational study to define the phenomena that lead to the onset of short length-scale (spike) rotating stall disturbances has been carried out. Based on unsteady simulations, we hypothesize there are two conditions necessary for the formation of spike disturbances, both of which are linked to the tip clearance flow. One is that the interface between the tip clearance and oncoming flows becomes parallel to the leading-edge plane. The second is the initiation of backflow, stemming from the fluid in adjacent passages, at the trailing-edge plane. The two criteria also imply a circumferential length scale for spike disturbances. The hypothesis and scenario developed are consistent with numerical simulations and experimental observations of axial compressor stall inception. A comparison of calculations for multiple blades with those for single passages also allows statements to be made about the utility of single passage computations as a descriptor of compressor stall.

An Experimental and Computational Investigation of Tip Clearance Flow and Its Impact on Stall Inception

2010 ◽  
Author(s):  
Matthew A. Bennington ◽  
Mark H. Ross ◽  
Joshua D. Cameron ◽  
Scott C. Morris ◽  
Juan Du ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Axial Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Momentum Balance ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow

A numerical and experimental study was conducted to investigate the tip clearance flow and its relationship to stall in a transonic axial compressor. The CFD results were used to identify the existence of an interface between incoming axial flow and the reverse tip clearance flow. A surface streaking method was used to experimentally identify this interface as a line of zero axial shear stress at the casing. The position of this line, denoted xzs, moved upstream with decreasing flow coefficient in both the experiments and computations. The line was found to be at the rotor leading edge plane when the compressor stalled. Further measurements using rotor offset and inlet distortion further corroborated these results, and demonstrated that the movement of the interface upstream of the leading edge leads to the generation of rotating (“spike”) disturbances. Stall was therefore interpreted to occur as a result of a critical momentum balance between the approach fluid and the tip-leakage flow.

Short Length-Scale Rotating Stall Inception in a Transonic Axial Compressor: Criteria and Mechanisms

2006 ◽  
Author(s):  
Chunill Hah ◽  
Jo¨rg Bergner ◽  
Heinz-Peter Schiffer
Keyword(s):  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Eddy Simulation ◽  
Clearance Flow ◽  
Flow Mechanisms ◽  
Tip Clearance Vortex

The current paper reports on investigations aimed at advancing the understanding of the flow mechanism that leads to the onset of short-length scale rotating stall in a transonic axial compressor. Experimental data show large oscillation of the tip clearance vortex as the rotor operates near the stall condition. Inception of spike-type rotating stall is also measured in the current transonic compressor with high response pressure transducers. Computational studies of a single passage and the full annulus were carried out to identify flow mechanisms behind the spike-type stall inception in the current transonic compressor rotor. Steady and unsteady single passage flow simulations were performed, first to get insight into the interaction between the tip clearance vortex and the passage shock. The conventional Reynolds-averaged Navier-Stokes method with a standard turbulence closure scheme does not accurately reproduce tip clearance vortex oscillation and the measured unsteady pressure field. Consequently, a Large Eddy Simulation (LES) was carried out to capture more relevant physics in the computational simulation of the rotating stall inception. The unsteady random behavior of the tip clearance vortex and it’s interaction with the passage shock seem to be critical ingredients in the development of spike-type rotating stall in a transonic compressor. The Large Eddy Simulation was further extended to the full annulus to identify flow mechanisms behind the measured spike-type rotating stall inception. The current study shows that the spike-type rotating stall develops after the passage shock is fully detached from the blade passages. Interaction between the tip clearance vortex and the passage shock creates a low momentum area near the pressure side of the blade. As the mass flow rate decreases, this low momentum area moves further upstream and reversed tip clearance flow is initiated at the trailing edge plane. Eventually, the low momentum area near the pressure side reaches the leading edge and forward spillage of the tip clearance flow occurs. The flows in the affected blade passage or passages then stall. As the stalled blade passages are formed behind the passage shock, the stalled area rotates counter to the blade rotation just like the classical Emmon’s type rotating stall. Both the measurements and the computations show that the rotating stall cell covers one to two blade passage lengths and rotates at roughly 50% of the rotor speed.

Short Length-Scale Rotating Stall Inception in a Transonic Axial Compressor: Experimental Investigation

2006 ◽  
Author(s):  
Jo¨rg Bergner ◽  
Matthias Kinzel ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah
Keyword(s):  
Experimental Investigation ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Wall Pressure ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Contour Plots ◽  
Transonic Axial Compressor

To improve the understanding of spike-type stall inception of a transonic axial compressor, measurements of the unsteady static pressure in the rotor endwall region are analyzed. At design speed, a detailed experimental investigation of the unsteadiness of the pressure field at the rotor endwall at near stall condition shows a strong fluctuation of the tip clearance flow. Both vortex strength and -trajectory oscillate randomly. Analysis of the wall pressure time histories during stall inception suggests that spike-type disturbances of the flow field correlate with an upstream motion of one blade passages shock front. In addition, the evolution of a stall cell could be visualized by means of static wall-pressure contour plots.

Experimental Study of Modal Disturbance and Rotating Stall Distribution

2013 ◽  
Vol 718-720 ◽  
pp. 1804-1810
Author(s):  
An Qing Lai ◽  
Jun Hu ◽  
Liang Li ◽  
Ju Luo
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Propagation Speed ◽  
Axial Direction ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Rotor Speed ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Modal Type

To execute stall active control technology effectively and make clear of stall inception induced by modal disturbance, this paper carries out the correlative research on modal disturbance and rotating stall on the two-stage low-speed axial compressor. The results indicate that the stall inception of the compressor is modal style and the modal oscillation propagates at 38% rotor speed while the stall cell propagation speed is 42% rotor speed. The phase angles of modal oscillation and rotating stall along the axial direction are different, but their trajectories are both similar to the blade passage shape. The stall mechanisms of modal-type and spike-type inceptions are different. It doesnt appear that leading-edge tip clearance flow spillage blow the blade tip while the modal-type stall formation.

scholarly journals Effects of Tip Clearance Flow on Rotating Stall Inception Process in an Axial Compressor Rotor

2013 ◽  
Vol 79 (801) ◽  
pp. 900-916 ◽  
Author(s):  
Kazutoyo YAMADA ◽  
Hiroaki KIKUTA ◽  
Masato FURUKAWA ◽  
Satoshi GUNJISHIMA ◽  
Yasunori HARA
Keyword(s):  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow

The Impact of Casing Groove Location on Stall Margin and Tip Clearance Flow in a Low-Speed Axial Compressor

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Du Juan ◽  
Li Jichao ◽  
Gao Lipeng ◽  
Lin Feng ◽  
Chen Jingyi
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
The Impact

In this study, the impact of single grooves at different locations on compressor stability and tip clearance flow are numerically and experimentally investigated. Initially, the numerical stall margin improvement (SMI) curve is examined using experimental data. Then, the evolution of the interface between the tip leakage flow (TLF) and the incoming main flow (MF) in the prestall and stall inception processes for two typical grooves, i.e., the worst and the optimal grooves in terms of their SMI, are compared with the smooth casing. The results show two different interface behaviors throughout the throttling process. The compressor with the worst single groove casing first experiences a long-length-scale disturbance after the interface near the blade suction side spills in front of the rotor leading-edge plane, and then goes through spikes after the whole interface spills. With the smooth casing and the optimal single groove near midchord, the interface reaches the rotor leading edge at the last stable operating point and spikes appear once the whole interface spills over the rotor leading edge. A model that illustrates the spillage patterns of the interface for the two stall precursors is thus proposed accordingly and used to explain their effectiveness in terms of the SMI. At last, the relevance of these results to the preliminary selection of groove locations for multigroove casing treatments (CTs) is verified by test data and discussed.

scholarly journals The Inner Workings of Axial Casing Grooves in a One and a Half Stage Axial Compressor With a Large Rotor Tip Gap: Changes in Stall Margin and Efficiency

2018 ◽  
Author(s):  
Chunill Hah
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Rates ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Flow Boundary ◽  
Clearance Flow ◽  
Large Rotor

Effects of axial casing grooves (ACGs) on the stall margin and efficiency of a one and a half stage low-speed axial compressor with a large rotor tip gap are investigated in detail. The primary focus of the current paper is to identify the flow mechanisms behind the changes in stall margin and on the efficiency of the compressor stage with a large rotor tip gap. Semicircular axial grooves installed in the rotor’s leading edge area are investigated. A large eddy simulation (LES) is applied to calculate the unsteady flow field in a compressor stage with ACGs. The calculated flow fields are first validated with previously reported flow visualizations and stereo PIV (SPIV) measurements. An in-depth examination of the calculated flow field indicates that the primary mechanism of the ACG is the prevention of full tip leakage vortex (TLV) formation when the rotor blade passes under the axial grooves periodically. The TLV is formed when the incoming main flow boundary layer collides with the tip clearance flow boundary layer coming from the opposite direction near the casing and rolls up around the rotor tip vortex. When the rotor passes directly under the axial groove, the tip clearance flow boundary layer on the casing moves into the ACGs and no roll-up of the incoming main flow boundary layer can occur. Consequently, the full TLV is not formed periodically as the rotor passes under the open casing of the axial grooves. Axial grooves prevent the formation of the full TLV. This periodic prevention of the full TLV generation is the main mechanism explaining how the ACGs extend the compressor stall margin by reducing the total blockage near the rotor tip area. Flows coming out from the front of the grooves affect the overall performance as it increases the flow incidence near the leading edge and the blade loading with the current ACGs. The primary flow mechanism of the ACGs is periodic prevention of the full TLV formation. Lower efficiency and reduced pressure rise at higher flow rates for the current casing groove configuration are due to additional mixing between the main passage flow and the flow from the grooves. At higher flow rates, blockage generation due to this additional mixing is larger than any removal of the flow blockage by the grooves. Furthermore, stronger double-leakage tip clearance flow is generated with this additional mixing with the ACGs at a higher flow rate than that of the smooth wall.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

On the Interpretation of Casing Measurements in Axial Compressors

2008 ◽  
Author(s):  
Joshua D. Cameron ◽  
Scott C. Morris ◽  
Sean T. Barrows ◽  
Jen-Ping Chen
Keyword(s):  
Experimental Studies ◽  
Rotating Stall ◽  
Basic Flow ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Axial Compressors ◽  
Clearance Flow ◽  
Flow Variables ◽  
Insight Into

Experimental studies of stall inception in axial compressors typically involve the measurement of basic flow variables (often pressure or velocity) with low spatial resolution. These measurements are used to make inferences about the fluid dynamics of stall. This experimental paradigm has been used by many investigators to great effect over the last several decades. However, several limitations remain which restrict the utility of these types of measurements for developing further insight into stall inception physics. Primary among these limitations is the impracticality of making measurements within the rotating blade passages. This is especially troublesome in light of recent computational studies which indicate that the generation of short length-scale rotating disturbances is related to the rotor tip clearance flow. This study utilized the results of a recent full annulus rotating stall simulation to investigate the relationships between the casing pressure field and less observable flow quantities which are believed to be causally related to the generation of rotating disturbances. The CFD results are assumed to represent the true flow physics within the compressor. To the extent that this approximation is true, these results can be used to interpret the meaning of experimental measurements of basic flow variables. These observations not only provide new insight into the interpretation of the large catalog of experimental stall measurements found in the literature, they also give directives for future measurements and numerical simulations.

Sign in / Sign up

Export Citation Format

Share Document