Investigation of Unsteady Flow Field in Vaned Diffuser of a Transonic Centrifugal Compressor

2006 ◽  
Author(s):  
Seiichi Ibaraki ◽  
Tetsuya Matsuo ◽  
Takao Yokoyama
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
Transonic Compressor ◽  
Inlet Conditions

Transonic centrifugal compressors are used with high-load turbochargers and turboshaft engines. These compressors usually have a vaned diffuser to increase the efficiency and the pressure ratio. To improve the performance of such a centrifugal compressor, it is required to optimize not only the impeller but also the diffuser. However the flow field of the diffuser is quite complex and unsteady because of the impeller located upstream. Although some research on vaned diffusers has been published, the diffuser flow is strongly dependent on the particular impeller exit flow, and some of the flow physics remain to be elucidated. In the research reported here, detailed flow measurements within a vaned diffuser were conducted using a particle image velocimetery (PIV). The vaned diffuser was designed with high subsonic inlet conditions marked by an inlet Mach number of 0.95 for the transonic compressor. As a result, a complex three-dimensional flow with distortion between the shroud and the hub was observed. Also, unsteady flow accompanying the inflow of the impeller wake was confirmed. Steady computational flow analysis was performed and compared with the experimental results.

Investigation of Unsteady Flow Field in a Vaned Diffuser of a Transonic Centrifugal Compressor

2006 ◽  
Vol 129 (4) ◽  
pp. 686-693 ◽  
Author(s):  
Seiichi Ibaraki ◽  
Tetsuya Matsuo ◽  
Takao Yokoyama
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
Transonic Compressor ◽  
Inlet Conditions

Transonic centrifugal compressors are used with high-load turbochargers and turboshaft engines. These compressors usually have a vaned diffuser to increase the efficiency and the pressure ratio. To improve the performance of such a centrifugal compressor, it is required to optimize not only the impeller but also the diffuser. However the flow field of the diffuser is quite complex and unsteady because of the impeller located upstream. Although some research on vaned diffusers has been published, the diffuser flow is strongly dependent on the particular impeller exit flow, and some of the flow physics remain to be elucidated. In the research reported here, detailed flow measurements within a vaned diffuser were conducted using a particle image velocimetery (PIV). The vaned diffuser was designed with high subsonic inlet conditions marked by an inlet Mach number of 0.95 for the transonic compressor. As a result, a complex three-dimensional flow with distortion between the shroud and the hub was observed. Also, unsteady flow accompanying the inflow of the impeller wake was confirmed. Steady computational flow analysis was performed and compared with the experimental results.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier–Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field and influenced by the unsteady interaction with the impeller. Detailed particle image velocimetry flow measurements within the diffuser are available for comparison purposes.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2007 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field, and influenced by the unsteady interaction with the impeller. Detailed Particle Image Velocimetry (PIV) flow measurements within the diffuser are available for comparison purposes.

Design and Off-Design Numerical Investigation of a Transonic Double-Splitter Centrifugal Compressor

2008 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Cross Sections ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Complex Flow ◽  
Flow Measurements ◽  
Vaned Diffuser

The flow field of a high pressure ratio centrifugal compressor for turbocharger applications is investigated using a three-dimensional Navier-Stokes solver. The compressor is composed of a double-splitter impeller followed by a vaned diffuser. The flow field of the transonic open-shrouded impeller is highly three-dimensional, and it is influenced by shock waves, tip leakage vortices and secondary flows. Their interactions generate complex flow structures which are convected and distorted through the impeller blades. Both steady and unsteady computations are performed in order to understand the physical mechanisms which govern the impeller flow field while the operation ranges from choke to surge. Detailed Laser Doppler Velocimetry (LDV) flow measurements are available at various cross-sections inside the impeller blades at both design and off-design operating conditions.

CFD Analysis of Unsteady Flow Interactions in a Centrifugal Compressor Stage

2000 ◽  
Author(s):  
A. Koumoutsos ◽  
A. Tourlidakis ◽  
R. L. Elder
Keyword(s):  
Steady State ◽  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Fourier Transforms ◽  
Flow Analysis ◽  
Design Flow ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage

This paper describes the unsteady flow analysis in a centrifugal compressor stage using a three dimensional CFD algorithm. The flow unsteadiness arising from the interaction between the impeller and the diffuser has been analysed using an algorithm suitable for equal or multiple number of rotor and diffuser blades. The multi-block, structured grid CFD code TASCflow was used as a basis and algorithm development was undertaken to provide the required capability of modelling the unsteady interactions of the impeller and the diffuser. The centrifugal compressor stage studied consists of an impeller with splitters and a vaned diffuser. The results presented are for off-design flow conditions where some experimental results were available for comparison. The results obtained for the steady-state model show a good agreement with the measurements. In general the unsteady flow field obtained show a reasonable agreement with experimental data and demonstrates significant differences when compared to the steady state results especially in terms of the velocity field. A detailed analysis of the unsteady flow field is carried out using Fourier transforms of velocity and pressure at various locations of the flow field and the level of unsteadiness is determined as distributed to various frequencies. The unsteadiness in the impeller passage is much less than in the diffuser where a strong coupling is predicted in the vaneless space.

Numerical Investigation of a Transonic Centrifugal Compressor

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Shock Waves ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Turbulence Models ◽  
Tip Clearance ◽  
Complex Flow ◽  
Low Velocity ◽  
Flow Measurements ◽  
Vaned Diffuser

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high-pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. The inlet flow to the open shrouded impeller is transonic, thus giving rise to interactions between shock waves and boundary layers and between shock waves and tip leakage vortices. These interactions generate complex flow structures which are convected and distorted through the impeller blades. Detailed laser Doppler velocimetry flow measurements are available at various cross sections inside the impeller blades highlighting the presence of low-velocity flow regions near the shroud. Particular attention is focused on understanding the physical mechanisms which govern the flow phenomena in the near shroud region. To this end numerical investigations are performed using different tip clearance modelizations and various turbulence models, and their impact on the computed flow field is discussed.

Numerical Investigation of a Transonic Centrifugal Compressor

2006 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Shock Waves ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Tip Clearance ◽  
Complex Flow ◽  
Low Velocity ◽  
Flow Measurements

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vane diffuser. The inlet flow to the open shrouded impeller is transonic, thus giving rise to interactions between shock waves and boundary layers and between shock waves and tip leakage vortices. These interactions generate complex flow structures which are convected and distorted through the impeller blades. Detailed Laser Doppler Velocimetry (LDV) flow measurements are available at various cross sections inside the impeller blades highlighting the presence of low velocity flow regions near the shroud. Particular attention is focused on understanding the physical mechanisms which govern the flow phenomena in the near shroud region. To this end numerical investigations are performed using different tip clearance modelizations and various turbulence models, and their impact on the computed flow field is discussed.

Numerical study on the Effect of Interaction Vaned Diffuser with Impeller on the Performance of a Modified Centrifugal Compressor

2013 ◽  
Vol 30 (2) ◽  
pp. 113-121 ◽  
Author(s):  
L. H. Jawad ◽  
S. Abdullah ◽  
R. Zulkifli ◽  
W. M. F. W. Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Internal Flow ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Compressor Impeller ◽  
Inlet Conditions

ABSTRACTThis paper is a numerical simulation that was made in the three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an auto-motive turbo charger. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between compressor impeller and vaned diffuser, influencing significantly surge and the efficiency of centrifugal compressor stages. In addition, a modified compressor impeller, coupled with vane and vaneless diffuser, has been found to have similar internal flow patterns for both the vaneless and vaned diffuser design. The vaned diffuser effect has been paid particular attention in terms of better analysis where the diffuser was designed for high sub-sonic inlet conditions. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken by using a commercial software, the so-called ANSYS CFX, to predict numerically the performance in terms of pressure ratio, poly tropic efficiency and mass flow rate for the centrifugal compressor stage. The results were generated from CFD and were analyzed for better understanding of the fluid flow through centrifugal compressor stage. Conclusively, it was observed that the effect of the vaned diffuser is to convert the kinetic energy into a high static pressure after analyzing the results of the simulation.

Optimization of 6.2:1 Pressure Ratio Centrifugal Compressor Impeller by 3D Inverse Design

2011 ◽  
Author(s):  
M. Zangeneh ◽  
N. Amarel ◽  
K. Daneshkhah ◽  
H. Krain
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Mechanical Performance ◽  
Design Method ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Inverse Design ◽  
Transonic Compressor ◽  
Design Variables ◽  
Compressor Impeller

In this work, the redesign of a centrifugal transonic compressor impeller with splitter blades by means of the three-dimensional inverse design code TURBOdesign-1 is presented. The basic design methodology for impellers with splitter blades is outlined and is applied in a systematic way to improve the aero/mechanical performance of a transonic 6.2:1 pressure ratio centrifugal compressor impeller. The primary design variables are the main and splitter blades loading and their thickness distributions, the splitter to main blade work ratio, as well as the span-wise swirl distribution. The flow in the original and redesigned impellers are then analyzed by means of a commercial CFD code (ANSYS CFX). The predicted flow field for the original impeller is compared with detailed L2F measurements inside and outside the impeller. The validated CFD results are used to compare the flow field in the optimized and original impeller. It is shown that the inverse design method could be effectively used to control the position and strength of the shock waves, eliminate flow separation and hence obtain a more uniform impeller exit flow in order to improve the aerodynamic performance. In addition, some results are presented on the comparison of stress and vibration in both impellers.

scholarly journals Analysis of the Unsteady Flow Field in a Centrifugal Compressor from Peak Efficiency to Near Stall with Full-Annulus Simulations

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Yannick Bousquet ◽  
Xavier Carbonneau ◽  
Guillaume Dufour ◽  
Nicolas Binder ◽  
Isabelle Trebinjac
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Suction Side ◽  
Operating Point ◽  
Peak Efficiency ◽  
Vaned Diffuser

This study concerns a 2.5 pressure ratio centrifugal compressor stage consisting of a splittered unshrouded impeller and a vaned diffuser. The aim of this paper is to investigate the modifications of the flow structure when the operating point moves from peak efficiency to near stall. The investigations are based on the results of unsteady three-dimensional simulations, in a calculation domain comprising all the blade. A detailed analysis is given in the impeller inducer and in the vaned diffuser entry region through time-averaged and unsteady flow field. In the impeller inducer, this study demonstrates that the mass flow reduction from peak efficiency to near stall leads to intensification of the secondary flow effects. The low momentum fluid accumulated near the shroud interacts with the main flow through a shear layer zone. At near stall condition, the interface between the two flow structures becomes unstable leading to vortices development. In the diffuser entry region, by reducing the mass flow, the high incidence angle from the impeller exit induces a separation on the diffuser vane suction side. At near stall operating point, vorticity from the separation is shed into vortex cores which are periodically formed and convected downstream along the suction side.

Sign in / Sign up

Export Citation Format

Share Document