scholarly journals Film Cooling From a Row of Holes Supplemented With Anti Vortex Holes

2007 ◽  
Author(s):  
Alok Dhungel ◽  
Yiping Lu ◽  
Wynn Phillips ◽  
Srinath V. Ekkad ◽  
James Heidmann
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Circular Cross Section ◽  
Flux Ratio ◽  
Upstream Region ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes ◽  
Film Cooling Holes

The primary focus of this paper is to study the film cooling performance for a row of cylindrical holes each supplemented with two symmetrical anti vortex holes which branch out from the main holes. The anti-vortex design was originally developed at NASA-Glenn Research Center by Dr. James Heidmann, co-author of this paper. This “anti-vortex” design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The hole design is intended to counteract the detrimental vorticity associated with standard circular cross-section film cooling holes. The geometry and orientation of the anti vortex holes greatly affect the cooling performance downstream, which is thoroughly investigated. By performing experiments at a single mainstream Reynolds number of 9683 based on the free stream velocity and film hole diameter at four different coolant-to-mainstream blowing ratio of 0.5, 1, 1.5, 2 and using the transient IR thermography technique, detailed film cooling effectiveness and heat transfer coefficients are obtained simultaneously from a single test. When the anti vortex holes are nearer to the primary film cooling holes and are developing from the base of the primary holes, better film cooling is accomplished as compared to other anti vortex hole orientations. When the anti vortex holes are laid back in the upstream region, film cooling diminishes considerably. Although an enhancement in heat transfer coefficient is seen in cases with high film cooling effectiveness, the overall heat flux ratio as compared to standard cylindrical holes is much lower. Thus cases with anti vortex holes placed near the main holes certainly show promising results.

scholarly journals Film Cooling From a Row of Holes Supplemented With Antivortex Holes

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
Alok Dhungel ◽  
Yiping Lu ◽  
Wynn Phillips ◽  
Srinath V. Ekkad ◽  
James Heidmann
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Circular Cross Section ◽  
Upstream Region ◽  
Cooling Effectiveness ◽  
Freestream Velocity ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes ◽  
Film Cooling Holes

The primary focus of this paper is to study the film cooling performance for a row of cylindrical holes each supplemented with two symmetrical antivortex holes, which branch out from the main holes. The antivortex design was originally developed at NASA-Glenn Research Center by James Heidmann, coauthor of this paper. This “antivortex” design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The hole design is intended to counteract the detrimental vorticity associated with standard circular cross-section film cooling holes. The geometry and orientation of the antivortex holes greatly affect the cooling performance downstream, which is thoroughly investigated. By performing experiments at a single mainstream Reynolds number of 9683 based on the freestream velocity and film hole diameter at four different coolant-to-mainstream blowing ratios of 0.5, 1, 1.5, and 2 and using the transient IR thermography technique, detailed film cooling effectiveness and heat transfer coefficients are obtained simultaneously from a single test. When the antivortex holes are nearer the primary film cooling holes and are developing from the base of the primary holes, better film cooling is accomplished as compared to other antivortex hole orientations. When the antivortex holes are laid back in the upstream region, film cooling diminishes considerably. Although an enhancement in heat transfer coefficient is seen in cases with high film cooling effectiveness, the overall heat flux ratio as compared to standard cylindrical holes is much lower. Thus cases with antivortex holes placed near the main holes certainly show promising results.

Film Cooling From a Row of Holes With Both Ends Embedded in Transverse Slots

2008 ◽  
Author(s):  
D. H. Zhang ◽  
L. Sun ◽  
Q. Y. Chen ◽  
M. Lin ◽  
M. Zeng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Aerodynamic Performance ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Discharge Coefficients ◽  
Cylindrical Holes

Embedding a row of typical cylindrical holes in a transverse slot can improve the cooling performance. Rectangular slots can increase the cooling effectiveness but is at the cost of decreasing of discharge coefficients. An experiment is conducted to examine the effects of an overlying transverse inclined trench on the film cooling performance of axial holes. Four different trench configurations are tested including the baseline inclined cylindrical holes. The influence of the geometry of the upstream lip of the exit trench and the geometry of the inlet trench on cooling performance is examined. Detailed film cooling effectiveness and heat transfer coefficients are obtained separately using the steady state IR thermography technique. The discharge coefficients are also acquired to evaluate the aerodynamic performance of different hole configurations. The results show that the film cooling holes with both ends embedded in slots can provide higher film cooling effectiveness and lower heat transfer coefficients; it also can provide higher discharge coefficients whilst retaining the mechanical strength of a row of discrete holes. The cooling performance and the aerodynamic performance of the holes with both ends embedded in inclined slots are superior to the holes with only exit trenched. To a certain extent, the configuration of the upstream lip of the exit trench affects the cooling performance of the downstream of the trench. The filleting for the film hole inlet avail the improvement of the cooling effect, but not for the film hole outlet. Comparing film cooling with embedded holes to unembedded holes, the overall heat flux ratio shows that the film holes with both ends embedded in slots and filleting for the film hole inlet can produce the highest heat flux reduction.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Cylindrical Holes

2017 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo ◽  
Ying-ni Zhai
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow Channels ◽  
Cylindrical Holes

This paper presents an experimental and numerical investigation on the film cooling with different coolant feeding channel structures. Two ribbed cross-flow channels with rib-orientation of 135° and 45° respectively and the plenum coolant channel have been studied and compared to find out the effect of rib orientation on the film cooling performances of cylindrical holes. The film cooling effectiveness and heat transfer coefficient were measured by the transient heat transfer measurement technique with narrow-band thermochromic liquid crystal. Numerical simulations with realizable k-ε turbulence model were also performed to analyze the flow mechanism. The results show that the coolant channel structure has a notable effect on the flow structure of film jet which is the most significant mechanism affecting the film cooling performance. Generally, film cooling cases fed with ribbed cross-flow channels have asymmetric counter-rotating vortex structures and related asymmetric temperature distributions, which make the film cooling effectiveness and the heat transfer coefficient distributions asymmetric to the hole centerline. The discharge coefficient of the 45° rib case is the lowest among the three cases under all the blowing ratios. And the plenum case has higher discharge coefficient than the 135° rib case under low blowing ratio. With the increase of blowing ratio, the discharge coefficient of the 135° rib case gets larger than the plenum case gradually, because the vortex in the upper half region of the coolant channel rotates in the same direction with the film hole inclination direction and makes the jet easy to flow into the film hole in the 135° rib case.

Effects of Film Hole Exit Radiusing on Film Cooling Performance

2016 ◽  
Author(s):  
Antar M. M. Abdala ◽  
Fifi N. M. Elwekeel ◽  
Qun Zheng
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Flux Ratio ◽  
Cooling Effectiveness ◽  
Flow Rates ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Net Heat Flux ◽  
Mass Flow Rates

In the present study, theoretical investigation of film cooling effectiveness and heat transfer behavior for radiusing of film hole exit was evaluated. Seven rounding radii of R=0.0D, 0.06D, 0.08D, 0.1D, 0.3D, 0.5D and 0.8D were investigated. The film cooling effectiveness, the heat transfer coefficient, net heat flux ratio and discharge coefficient were investigated. Four mass flow rates in the range of 0.00044: 0.0018[kg/s] were used to investigate the effects of coolant velocity on the film cooling performance. Results show that using the film hole exit radiusing helps in improvement the film cooling effectiveness. The radius of R=0.5D shows higher film cooling effectiveness among the other radii. The spatially average laterally film cooling effectiveness and net heat flux ratio of R=0.5D outperforms the case of R=0.0D at all mass flow rates except at higher rates the values are lower. Discharge coefficient of R=0.5D shows enhancement than R=0.0D with the pressure ratios. Interpretation of the low and high heat transfer coefficient regions for radii of R=0.5D and R= 0.0D depending on the flow structures was explained in detail.

Film Cooling Characteristic of Double-Fan-Shaped Film Cooling Holes

2009 ◽  
Author(s):  
Jiang-Tao Bai ◽  
Hui-ren Zhu ◽  
Cun-liang Liu
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Diameter Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes ◽  
Film Cooling Holes

The film cooling performance downstream of a single row of double-fan-shaped film cooling holes in a flat plate have been investigated by experimental measurements and numerical simulation. The entrance and exit of double-fan-shaped holes are comprised of a lateral expansion of 15° from the original simple cylindrical shape with stream-wise inclination of 45°. The width of the exit face to cylinder diameter ratio is 1.5; the length-to-diameter ratio is 4.24 and the pitch-to-diameter ratio is 3. The experimental method used to obtain the adiabatic film cooling effectiveness values and the heat transfer coefficient is a transient narrow band liquid crystal technique. Both film cooling effectiveness and heat transfer coefficient are measured at three momentum ratios (I = 0.5, 1, 2) at constant Reynolds number (Re = 10000) and free stream turbulence (Tu = 2%). The film cooling effectiveness, heat transfer coefficient and Net Heat Flux Reduction (NHFR) are presented for detailed distribution and span-wise averaged values. Discharge coefficients are also measured in the experiment. A commercial package is used to numerically simulate the flow and heat transfer of double-fan-shaped holes; simple cylindrical holes are also simulated for comparison. Numerical simulation use RNG turbulence model with a standard wall function for near wall region. Experimental and Numerical simulation results show that: 1) the double-fan-shaped holes present higher discharge coefficient than simple cylindrical holes at respective momentum ratio; 2) the numerical simulation film cooling effectiveness results of double-fan-shaped holes accord well with the experimental results; 3) at measured three momentum ratios, the double-fan-shaped holes demonstrate better film cooling performance (higher NHFR) than simple cylindrical holes, better film cooling expansion on span-wise; 4) the best momentum ratio of double-fan-shaped holes is 0.5.

Film Cooling From a Row of Holes Embedded in Transverse Slots

2005 ◽  
Author(s):  
Yiping Lu ◽  
Hasan Nasir ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Flux Ratio ◽  
Stream Velocity ◽  
Cooling Performance ◽  
Cylindrical Holes ◽  
Film Cooling Holes

Film cooling performance for a row of cylindrical holes can be enhanced by embedding the row in transverse slots. The geometry of the transverse slot greatly affects the cooling performance downstream of injection. The effect of the slot exit area and edge shape is investigated. Detailed heat transfer coefficient and film effectiveness measurements are obtained simultaneously using a single test transient IR thermography technique. The study is performed at a single mainstream Reynolds number based on free-stream velocity and film hole diameter of 7150 at three different coolant-to-mainstream blowing ratios of 0.5, 1.0, and 1.5. The results show that the film cooling holes provide higher film effectiveness when embedded in a slot. However, in some geometries when the slot begins at the upstream edge of the hole, the film effectiveness diminishes. The heat transfer coefficient enhancement due to the embedding is not significantly higher compared to the typical unembedded cylindrical hole. The overall heat flux ratio comparing film cooling with embedded holes to unembedded holes shows that the full slot and downstream slot spacing after the hole exit produce the highest heat flux reduction. The holes-in-slot geometry is certainly very promising.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Compound Holes

2018 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Orientation Angle ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To investigate the effects of the inclined ribs on internal flow structure in film hole and the film cooling performance on outer surface, experimental and numerical studies are conducted on the effects of rib orientation angle on film cooling of compound cylindrical holes. Three coolant channel cases, including two ribbed cross-flow channels (135° and 45° angled ribs) and the plenum case, are studied under three blowing ratios (0.5, 1.0 and 2.0). 2D contours of film cooling effectiveness as well as heat transfer coefficient were measured by transient liquid crystal measurement technique (TLC). The steady RANS simulations with realizable k-ε turbulence model and enhanced wall treatment were performed. The results show that the spanwise width of film coverage is greatly influenced by the rib orientation angle. The spanwise width of the 45° rib case is obviously larger than that of the 135° rib case under lower blowing ratios. When the blowing ratio is 1.0, the area-averaged cooling effectiveness of the 135° rib case and the 45° rib case are higher than that of the plenum case by 38% and 107%, respectively. With the increase of blowing ratio, the film coverage difference between different rib orientation cases becomes smaller. The 45° rib case also produces higher heat transfer coefficient, which is higher than the 135° rib case by 3.4–8.7% within the studied blowing ratio range. Furthermore, the discharge coefficient of the 45° rib case is the lowest among the three cases. The helical motion of coolant flow is observed in the hole of 45° rib case. The jet divides into two parts after being blown out of the hole due to this motion, which induces strong velocity separation and loss. For the 135° rib case, the vortex in the upper half region of the secondary-flow channel rotates in the same direction with the hole inclination direction, which leads to the straight streamlines and thus results in lower loss and higher discharge coefficient.

Rib Turbulator Effects on Crossflow-Fed Shaped Film Cooling Holes

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Dale W. Fox ◽  
Fraser B. Jones ◽  
John W. McClintic ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
...  
Keyword(s):  
Film Cooling ◽  
Velocity Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Smooth Channel ◽  
Cooling Hole ◽  
Film Cooling Holes ◽  
Inlet Position ◽  
The Impact

Most studies of turbine airfoil film cooling in laboratory test facilities have used relatively large plenums to feed flow into the coolant holes. However, a more realistic inlet condition for the film cooling holes is a relatively small channel. Previous studies have shown that the film cooling performance is significantly degraded when fed by perpendicular internal crossflow in a smooth channel. In this study, angled rib turbulators were installed in two geometric configurations inside the internal crossflow channel, at 45 deg and 135 deg, to assess the impact on film cooling effectiveness. Film cooling hole inlets were positioned in both prerib and postrib locations to test the effect of hole inlet position on film cooling performance. A test was performed independently varying channel velocity ratio and jet to mainstream velocity ratio. These results were compared to the film cooling performance of previously measured shaped holes fed by a smooth internal channel. The film cooling hole discharge coefficients and channel friction factors were also measured for both rib configurations with varying channel and inlet velocity ratios. Spatially averaged film cooling effectiveness is largely similar to the holes fed by the smooth internal crossflow channel, but hole-to-hole variation due to inlet position was observed.

Effect of Internal Crossflow Velocity on Film Cooling Effectiveness: Part II — Compound Angle Shaped Holes

2017 ◽  
Author(s):  
John W. McClintic ◽  
Joshua B. Anderson ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
Zachary D. Webster
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Film Cooling ◽  
Velocity Ratio ◽  
Injection Rate ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Crossflow Velocity ◽  
Film Cooling Holes ◽  
Compound Angle

In gas turbine engines, film cooling holes are commonly fed with an internal crossflow, the magnitude of which has been shown to have a notable effect on film cooling effectiveness. In Part I of this study, as well as in a few previous studies, the magnitude of internal crossflow velocity was shown to have a substantial effect on film cooling effectiveness of axial shaped holes. There is, however, almost no data available in the literature that shows how internal crossflow affects compound angle shaped film cooling holes. In Part II, film cooling effectiveness, heat transfer coefficient augmentation, and discharge coefficients were measured for a single row of compound angle shaped film cooling holes fed by internal crossflow flowing both in-line and counter to the span-wise direction of coolant injection. The crossflow-to-mainstream velocity ratio was varied from 0.2–0.6 and the injection velocity ratio was varied from 0.2–1.7. It was found that increasing the magnitude of the crossflow velocity generally caused degradation of the film cooling effectiveness, especially for in-line crossflow. An analysis of jet characteristic parameters demonstrated the importance of crossflow effects relative to the effect of varying the film cooling injection rate. Heat transfer coefficient augmentation was found to be primarily dependent on injection rate, although for in-line crossflow, increasing crossflow velocity significantly increased augmentation for certain conditions.

Film Cooling Mechanism of Combined Hole and Saw-tooth Slot

2019 ◽  
Vol 36 (4) ◽  
pp. 425-433
Author(s):  
Wei Zhang ◽  
Shuai Zhou ◽  
Zhuang Wu ◽  
Guangchao Li ◽  
Zhihai Kou
Keyword(s):  
Film Cooling ◽  
Numerical Data ◽  
Diameter Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Inclination Angles ◽  
Cylindrical Holes ◽  
Cooling Mechanism ◽  
Experimental Values

Abstract Film cooling performance of one row of cylindrical holes integrated with saw-tooth slots was numerically studied at blowing ratios of 0.5, 1.0 1.5 and 2.0 respectively. The saw-tooth slot concept combines the advantages both of easy machining for the slot and of the high film cooling effectiveness caused by the anti-vortex induced by the shaped hole. The film holes have an inclination angles of 30°, length to diameter ratio of 4 and pitch to diameter ratio of 3. The corner angles of the saw-tooth are 60°, 90°, 120°, 150° and 180° respectively. The 180° corner angle corresponds to a standard transverse slot. The emphasis of this other is on the influence of the corner angles of the saw-tooth on film cooling effectiveness. The flow field and thermal field were obtained to explain the mechanism of film cooling performance improvement by the saw-tooth slot. The results show that the numerical data agrees with the experimental values for the cylindrical holes. Relatively small corner angles generate uniform local film cooling effectiveness and high spanwise averaged film cooling effectiveness due to the coolant ejected from the hole smoothly flowing into the slot. The effect of corner angles strongly depends on blowing ratios. The increase of x/D decreases the differences of film cooling effectiveness between various corner angles. At low blowing ratios, an anti-vortex can be found with the spanwise angle of 60° and 120°. At high blowing ratios, an anti-vortex can be found with the spanwise angle of 60°.

Sign in / Sign up

Export Citation Format

Share Document