Aero-Thermal Investigations of Tip Leakage Flow In Axial Flow Turbines: Part I — Effect of Tip Geometry and Tip Clearance Gap

2007 ◽  
Author(s):  
S. K. Krishnababu ◽  
P. J. Newton ◽  
W. N. Dawes ◽  
G. D. Lock ◽  
H. P. Hodson ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Axial Flow ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Heat Transfer Characteristics ◽  
Tip Leakage ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

A numerical study has been performed to investigate the effect of tip geometry on the tip leakage flow and heat transfer characteristics in unshrouded axial flow turbines. Baseline flat tip geometry and squealer type geometries namely double squealer or cavity and suction side squealer were considered. The performances of the squealer geometries, in terms of the leakage mass flow and heat transfer to the tip, were compared with the flat tip at two different tip clearance gaps. The computations were performed using a single blade with periodic boundary conditions imposed along the boundaries in the pitchwise direction. Turbulence was modelled using three different models namely standard k-ε, low Re k-ω and SST k-ω, in order to assess the capability of the models in correctly predicting the blade heat transfer. The heat transfer and static pressure distributions obtained using the SST k-ω model was found to be in close agreement with the experimental data. It was observed that compared to the other two geometries considered, the cavity tip is advantageous both from the aerodynamic and from the heat transfer perspectives by providing a decrease in the amount of leakage, and hence losses, and average heat transfer to the tip. In general, for a given geometry, the leakage mass flow and the heat transfer to the tip increased with increase in tip clearance gap. Part II of this paper examines the effect of relative casing motion on the flow and heat transfer characteristics of tip leakage flow. In Part III of this paper the effect of coolant injection on the flow and heat transfer characteristics of tip leakage flow is presented.

Aerothermal Investigations of Tip Leakage Flow in Axial Flow Turbines—Part I: Effect of Tip Geometry and Tip Clearance Gap

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
S. K. Krishnababu ◽  
P. J. Newton ◽  
W. N. Dawes ◽  
G. D. Lock ◽  
H. P. Hodson ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Axial Flow ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Heat Transfer Characteristics ◽  
Tip Leakage ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

A numerical study has been performed to investigate the effect of tip geometry on the tip leakage flow and heat transfer characteristics in unshrouded axial flow turbines. Base line flat tip geometry and squealer type geometries, namely, double squealer or cavity and suction-side squealer, were considered. The performances of the squealer geometries, in terms of the leakage mass flow and heat transfer to the tip, were compared with the flat tip at two different tip clearance gaps. The computations were performed using a single blade with periodic boundary conditions imposed along the boundaries in the pitchwise direction. Turbulence was modeled using three different models, namely, standard k-ε, low Re k-ω, and shear stress transport (SST) k-ω, in order to assess the capability of the models in correctly predicting the blade heat transfer. The heat transfer and static pressure distributions obtained using the SST k-ω model were found to be in close agreement with the experimental data. It was observed that compared to the other two geometries considered, the cavity tip is advantageous both from the aerodynamic and from the heat transfer perspectives by providing a decrease in the amount of leakage, and hence losses, and average heat transfer to the tip. In general, for a given geometry, the leakage mass flow and the heat transfer to the tip increased with increase in tip clearance gap. Part II of this paper examines the effect of relative casing motion on the flow and heat transfer characteristics of tip leakage flow. In Part III of this paper the effect of coolant injection on the flow and heat transfer characteristics of tip leakage flow is presented.

scholarly journals Effect of Tip Clearance on Flow Field and Heat Transfer Characteristics in a Large Meridional Expansion Turbine

Energies ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 162 ◽  
Author(s):  
Fusheng Meng ◽  
Qun Zheng ◽  
Jie Gao ◽  
Weiliang Fu
Keyword(s):  
Heat Transfer ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Heat Transfer Characteristics ◽  
Tip Leakage ◽  
Turbine Stator ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Expansion Turbine

The large meridional expansion turbine stator leads to complex secondary flows and heat transfer characteristics in the blade endwall region, while the upstream tip clearance leakage flow of the rotor makes it more complex in flow and heat transfer. The influence of the upstream rotor tip clearance on the large meridian expansion stator is worth studying. The flow and heat transfer characteristics of the downstream large meridional expansion turbine stator were studied by comparing the tip leakage flow of 1.5-stage shrouded and unshrouded turbines using a three-dimensional Reynolds-Averaged Navier-Stokes (RANS) solver for viscous turbulent flows. Validation studies were performed to investigate the aerodynamics and heat transfer prediction ability of the shear stress transport (SST) turbulence model. The influence of different tip clearances of the rotor including unshrouded blade heights of 0%, 1% and 5% and a 1% shrouded blade height were investigated through numerical simulation. The results showed that the upper passage vortex separation was more serious and the separation, and attachment point of horseshoe vortex in the pressure side were significantly more advanced than that of non-expansion turbines. The tip leakage vortex obviously increased the negative incidence angle at the downstream inlet. Furthermore, the strength of the high heat transfer zone on the suction surface of the downstream stator was significantly increased, while that of the shrouded rotor decreased.

Tip Leakage Flow and Heat Transfer Characteristics on Rotor Casing and Blade Tip in an Axial Gas Turbine Engine: Steady Analysis

2008 ◽  
Author(s):  
Md Hamidur Rahman ◽  
Sung In Kim ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Heat Transfer Characteristics ◽  
Turbine Engine ◽  
Tip Leakage ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Blade Tip

Steady simulations have been performed to investigate tip leakage flow and heat transfer characteristics on the casing and rotor blade tip in a single stage turbine engine. A turbine stage of stator and rotor was modeled with a pressure ratio of 3.2. The predicted isentropic Mach number and adiabatic wall temperature on the casing showed good agreement with available experimental data. The effects of tip clearance height and rotor rotational speed on the blade tip and casing heat transfer characteristics are mainly considered. It is observed that the tip leakage flow structure is highly dependent on the height of the tip gap as well as speeds of the rotor blade. In all cases, flow separates just around the corner of the pressure side of the blade tip. The region of recirculating flow increases with the increase of the clearance height. Then the flow reattaches on the tip surface near the suction side beyond the flow separation. This flow reattachment enhances surface heat transfer. The leakage flow interaction with the reverse cross flow, induced by relative casing motion, is found to have significant effect on the blade tip and casing heat transfer distribution. Critical region of high heat transfer on the casing exists near the blade tip leading edge and along the pressure side edge at all clearance height. Whereas, at high speed rotation, it tends to move towards the trailing edge due to the change of inflow angle.

Aero-Thermal Investigation of Tip Leakage Flow in a Film Cooled Industrial Turbine Rotor

2008 ◽  
Author(s):  
S. K. Krishnababu ◽  
H. P. Hodson ◽  
G. D. Booth ◽  
G. D. Lock ◽  
W. N. Dawes
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flow ◽  
Turbine Rotor ◽  
Total Heat ◽  
Leakage Flow ◽  
Total Heat Flux ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Flow And Heat Transfer

A numerical investigation of the flow and heat transfer characteristics of tip leakage in a typical film cooled industrial gas turbine rotor is presented in this paper. The computations were performed on a rotating domain of a single blade with a clearance gap of 1.28% chord in an engine environment. This standard blade featured two coolant and two dust holes, in a cavity-type tip with a central rib. The computations were performed using CFX 5.6, which was validated for similar flow situations by Krishnababu et al., [18]. These predictions were further verified by comparing the flow and heat transfer characteristics computed in the absence of coolant ejection with computations previously performed in the company (SIEMENS) using standard in-house codes. Turbulence was modelled using the SST k-ω turbulence model. The comparison of calculations performed with and without coolant ejection has shown that the coolant flow partially blocks the tip gap, resulting in a reduction of the amount of mainstream leakage flow. The calculations identified that the main detrimental heat transfer issues were caused by impingement of the hot leakage flow onto the tip. Hence three different modifications (referred as Cases 1 to 3) were made to the standard blade tip in an attempt to reduce the tip gap exit mass flow and the associated impingement heat transfer. The improvements and limitations of the modified geometries, in terms of tip gap exit mass flow, total area of the tip affected by the hot flow and the total heat flux to the tip, are discussed. The main feature of the Case 1 geometry is the removal of the rib and this modification was found to effectively reduce both the total area affected by the hot leakage flow and total heat flux to the tip while maintaining the same leakage mass flow as the standard blade. Case 2 featured a rearrangement of the dust holes in the tip which, in terms of aero-thermal-dynamics, proved to be marginally inferior to Case 1. Case 3, which essentially created a suction-side squealer geometry, was found to be inferior even to the standard cavity tip blade. It was also found that the hot spots which occur in the leading edge region of the standard tip and all modifications contributed significantly to the area affected by the hot tip leakage flow and the total heat flux.

Numerical Simulation of Tip Leakage Flows in Axial Flow Turbines, With Emphasis on Flow Physics: Part I — Effect of Tip Clearance Height

2000 ◽  
Author(s):  
J. Tallman ◽  
B. Lakshminarayana
Keyword(s):  
Mass Flow ◽  
Axial Flow ◽  
Numerical Procedure ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Flow Physics ◽  
Tip Leakage ◽  
Inlet Conditions

A pressure-correction based, 3D Navier-Stokes CFD code was used to simulate the effects of turbine parameters on the tip leakage flow and vortex in a linear turbine cascade to understand the detailed flow physics. A baseline case simulation of a cascade was first conducted in order to validate the numerical procedure with experimental measurements. The effects of realistic tip clearance spacing, inlet conditions, and relative endwall motion were then sequentially simulated, while maintaining previously modified parameters. With each additional simulation, a detailed comparison of the leakage flow’s direction, pressure gradient, and mass flow, as well as the leakage vortex and its roll-up, size, losses, location, and interaction with other flow features, was conducted. Part I of this two-part paper series focuses on the effect of reduced tip clearance height on the leakage flow and vortex. Reduced tip clearance resulted in less mass flow through the gap, a smaller leakage vortex, and less aerothermal losses in both the gap and the vortex. The shearing of the leakage jet and passage flow to which leakage vortex roll-up is usually attributed to was not observed in any of the simulations. Alternative explanations of the leakage vortex’s roll-up are presented. Additional secondary flows that were seen near the casing were also discussed. A more thorough thesis on the research presented in this paper can be found at the World Wide Web address http://navier.aero.psu.edu/∼jat.

Aero-Thermal Investigations of Tip Leakage Flow In Axial Flow Turbines: Part II — Effect of Relative Casing Motion

2007 ◽  
Author(s):  
S. K. Krishnababu ◽  
W. N. Dawes ◽  
H. P. Hodson ◽  
G. D. Lock ◽  
J. Hannis ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Numerical Study ◽  
Axial Flow ◽  
Suction Side ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Average Heat ◽  
Tip Leakage

A numerical study has been performed to investigate the effect of casing motion on the tip leakage flow and heat transfer characteristics in unshrouded axial flow turbines. The relative motion between the blade tip and the casing was simulated by moving the casing in a direction from the suction side to the pressure side of the stationary blade. Baseline flat tip geometry and squealer type geometries namely double squealer or cavity and suction side squealer were considered at a clearance gap of 1.6%C. The computations were performed using a single blade with periodic boundary conditions imposed along the boundaries in the pitchwise direction. Turbulence was modelled using the SST k-ω model. The flow conditions correspond to an exit Reynolds number of 2.3×105. The results were compared with those obtained without the relative casing motion reported in part I of this paper. In general, the effect of relative casing motion was to decrease the tip leakage mass flow and the average heat transfer to the tip due to the decrease in leakage flow velocity caused by a drop in driving pressure difference. Compared to the computations with stationary casing, in the case of all the three geometries considered, the average heat transfer to the suction surface of the blade was found to be larger in the case of the computations with relative casing motion. At a larger clearance gap of 2.8%C, in case of flat tip, while the tip leakage mass flow decreased due to relative casing motion only a smaller change in the average heat transfer to the tip and the suction surface of the blade was noticed.

Aerothermal Investigations of Tip Leakage Flow in Axial Flow Turbines—Part II: Effect of Relative Casing Motion

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
S. K. Krishnababu ◽  
W. N. Dawes ◽  
H. P. Hodson ◽  
G. D. Lock ◽  
J. Hannis ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Axial Flow ◽  
Suction Side ◽  
Leakage Flow ◽  
Base Line ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Average Heat ◽  
Tip Leakage

A numerical study has been performed to investigate the effect of casing motion on the tip leakage flow and heat transfer characteristics in unshrouded axial flow turbines. The relative motion between the blade tip and the casing was simulated by moving the casing in a direction from the suction side to the pressure side of the stationary blade. Base line flat tip geometry and squealer type geometries, namely, double squealer or cavity and suction side squealer, were considered at a clearance gap of 1.6%C. The computations were performed using a single blade with periodic boundary conditions imposed along the boundaries in the pitchwise direction. Turbulence was modeled using the shear stress transport k-ω model. The flow conditions correspond to an exit Reynolds number of 2.3×105. The results were compared to those obtained without the relative casing motion reported in Part I of this paper. In general, the effect of relative casing motion was to decrease the tip leakage mass flow and the average heat transfer to the tip due to the decrease in leakage flow velocity caused by a drop in driving pressure difference. Compared to the computations with stationary casing, in the case of all the three geometries considered, the average heat transfer to the suction surface of the blade was found to be larger in the case of the computations with relative casing motion. At a larger clearance gap of 2.8%C, in case of a flat tip, while the tip leakage mass flow decreased due to relative casing motion, only a smaller change in the average heat transfer to the tip and the suction surface of the blade was noticed.

Numerical Simulation of Tip Leakage Flows in Axial Flow Turbines, With Emphasis on Flow Physics: Part I—Effect of Tip Clearance Height

2000 ◽  
Vol 123 (2) ◽  
pp. 314-323 ◽  
Author(s):  
J. Tallman ◽  
B. Lakshminarayana
Keyword(s):  
Mass Flow ◽  
Axial Flow ◽  
Numerical Procedure ◽  
Secondary Flows ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Flow Physics ◽  
Tip Leakage ◽  
Inlet Conditions

A pressure-correction based, 3D Navier-Stokes CFD code was used to simulate the effects of turbine parameters on the tip leakage flow and vortex in a linear turbine cascade to understand the detailed flow physics. A baseline case simulation of a cascade was first conducted in order to validate the numerical procedure with experimental measurements. The effects of realistic tip clearance spacing, inlet conditions, and relative endwall motion were then sequentially simulated, while maintaining previously modified parameters. With each additional simulation, a detailed comparison of the leakage flow’s direction, pressure gradient, and mass flow, as well as the leakage vortex and its roll-up, size, losses, location, and interaction with other flow features, was conducted. Part I of this two-part paper focuses on the effect of reduced tip clearance height on the leakage flow and vortex. Reduced tip clearance results in less mass flow through the gap, a smaller leakage vortex, and less aerothermal losses in both the gap and the vortex. The shearing of the leakage jet and passage flow to which leakage vortex roll-up is usually attributed to is not observed in any of the simulations. Alternative explanations of the leakage vortex’s roll-up are presented. Additional secondary flows that are seen near the casing are also discussed.

On Prediction of Tip Leakage Flow and Heat Transfer in Gas Turbines

2004 ◽  
Author(s):  
Fadil Mumic ◽  
Daniel Eriksson ◽  
Bengt Sunde´n
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbines ◽  
Numerical Study ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Flow And Heat Transfer

A numerical study has been performed to simulate the tip leakage flow and heat transfer on the first stage of a high-pressure turbine, which represents a modern gas turbine blade geometry. The low Re k-ω (SST) model is used to model the turbulence. Calculations are performed for both a flat and a squealer blade tip for three different tip gap clearances. The computations were carried out using a single blade with periodic conditions imposed along the boundaries in the circumferential (pitch) direction. The predicted tip heat transfer and static pressure distributions show reasonable agreement with experimental data. It was also observed that the tip clearance has a significant influence on local tip heat transfer coefficient distribution. The flat tip blade provides a higher overall heat transfer coefficient than the squealer tip blade.

Sign in / Sign up

Export Citation Format

Share Document