Experimental Investigation of a Generic, Fuel Flexible Reheat Combustor at Gas Turbine Relevant Operating Conditions

2010 ◽  
Author(s):  
Julia M. Fleck ◽  
Peter Griebel ◽  
Adam M. Steinberg ◽  
Michael Sto¨hr ◽  
Manfred Aigner ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Natural Gas ◽  
Boundary Conditions ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Primary Energy ◽  
Operating Conditions ◽  
Energy Sources ◽  
Fuel Flexibility ◽  
Low Emission

Fuel flexibility in stationary gas turbines (GT) is becoming increasingly important due to the use of a broader spectrum of primary energy sources, particularly H2-rich fuels derived from the gasification of coal or biomass. GTs also must be able to operate at extremely low emission levels, which is currently achieved with lean-premixed burner designs. To investigate the performance of highly reactive fuels in the reheat combustion concept, mainly with respect to autoignition and flashback limits, a generic reheat combustor with excellent optical access has been developed. The first objective of this work was to carefully characterize the mixing section in order to derive well-defined boundary conditions for the subsequent autoignition studies. Initial autoignition results at T > 1000 K and p = 15 bar are presented for natural gas (NG) and H2-rich fuels. No autoignition was detected for NG at the investigated operating conditions. For H2/NG/N2 blends with a constant volumetric N2 concentration of 20% and H2 concentrations higher than 76%, autoignition in the mixing section was detected.

Fuel Flexibility in LM2500 and LM6000 Dry Low Emission Engines

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
John Blouch ◽  
Hejie Li ◽  
Mark Mueller ◽  
Richard Hook
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Inert Gases ◽  
Effect Of Temperature ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Kinetics Analysis ◽  
Fuel Flexibility ◽  
Low Emission ◽  
Commercial Operation

The LM2500 and LM6000 dry-low-emissions aeroderivative gas turbine engines have been in commercial service for 15 years and have accumulated nearly 10 × 106 hours of commercial operation. The majority of these engines utilize pipeline quality natural gas predominantly comprised of methane. There is; however, increasing interest in nonstandard fuels that contain varying levels of higher hydrocarbon species and/or inert gases. This paper reports on the demonstrated operability of LM2500 and LM6000 DLE engines with nonstandard fuels. In particular, rig tests at engine conditions were performed to demonstrate the robustness of the dual-annular counter-rotating swirlers premixer design, relative to flameholding with fuels containing high ethane, propane, and N2 concentrations. These experiments, which test the ability of the hardware to shed a flame introduced into the premixing region, have been used to expand the quoting limits for LM2500 and LM6000 gas turbine engines to elevated C2+ levels. In addition, chemical kinetics analysis was performed to understand the effect of temperature, pressure, and fuel compositions on flameholding. Test data for different fuels and operating conditions were successfully correlated with Damkohler number.

Fuel Flexibility in LM2500 and LM6000 Dry Low Emission Engines

2011 ◽  
Author(s):  
John Blouch ◽  
Hejie Li ◽  
Mark Mueller ◽  
Richard Hook
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Inert Gases ◽  
Effect Of Temperature ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Kinetics Analysis ◽  
Fuel Flexibility ◽  
Low Emission ◽  
Commercial Operation

The LM2500 and LM6000 dry-low-emissions (DLE) aeroderivative gas turbine engines have been in commercial service for 15 years and have accumulated nearly 10 million hours of commercial operation. The majority of these engines utilize pipeline quality natural gas predominantly comprised of methane. There is, however, increasing interest in nonstandard fuels that contain varying levels of higher hydrocarbon species and/or inert gases. This paper reports on the demonstrated operability of LM2500 and LM6000 DLE engines with nonstandard fuels. In particular, rig tests at engine conditions were performed to demonstrate the robustness of the dual-annular counter-rotating swirlers (DACRS) premixer design, relative to flameholding with fuels containing high ethane, propane, and N2 concentrations. These experiments, which test the ability of the hardware to shed a flame introduced into the premixing region, have been used to expand the quoting limits for LM2500 and LM6000 gas turbine engines to elevated C2+ levels. In addition, chemical kinetics analysis was performed to understand the effect of temperature, pressure, and fuel compositions on flameholding. Test data for different fuels and operating conditions were successfully correlated with Damkohler number.

Gas Turbine Fouling: The Influence of Climate and Part-Load Operating Conditions

2019 ◽  
Author(s):  
Nicola Aldi ◽  
Nicola Casari ◽  
Mirko Morini ◽  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
...  
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Environmental Influence ◽  
Electrical Power ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Continuous Increase ◽  
Part Load

Abstract Energy and climate change policies associated with the continuous increase in natural gas costs pushed governments to invest in renewable energy and alternative fuels. In this perspective, the idea to convert gas turbines from natural gas to syngas from biomass gasification could be a suitable choice. Biogas is a valid alternative to natural gas because of its low costs, high availability and low environmental impact. Syngas is produced with the gasification of plant and animal wastes and then burnt in gas turbine combustor. Although synfuels are cleaned and filtered before entering the turbine combustor, impurities are not completely removed. Therefore, the high temperature reached in the turbine nozzle can lead to the deposition of contaminants onto internal surfaces. This phenomenon leads to the degradation of the hot parts of the gas turbine and consequently to the loss of performance. The amount of the deposited particles depends on mass flow rate, composition and ash content of the fuel and on turbine inlet temperature (TIT). Furthermore, compressor fouling plays a major role in the degradation of the gas turbine. In fact, particles that pass through the inlet filters, enter the compressor and could deposit on the airfoil. In this paper, the comparison between five (5) heavy-duty gas turbines is presented. The five machines cover an electrical power range from 1 MW to 10 MW. Every model has been simulated in six different climate zones and with four different synfuels. The combination of turbine fouling, compressor fouling, and environmental conditions is presented to show how these parameters can affect the performance and degradation of the machines. The results related to environmental influence are shown quantitatively, while those connected to turbine and compressor fouling are reported in a more qualitative manner. Particular attention is given also to part-load conditions. The power units are simulated in two different operating conditions: 100 % and 80 % of power rate. The influence of this variation on the intensity of fouling is also reported.

Operability Limits of Tubular Injectors With Vortex Generators for a Hydrogen-Fueled Recuperated 100 kW Class Gas Turbine

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Stefan Bauer ◽  
Balbina Hampel ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Bulk Flow ◽  
Vortex Generators ◽  
Inlet Temperature ◽  
Test Rig ◽  
Temperature Range ◽  
Wide Range

Abstract Vortex generators are known to be effective in augmenting the mixing of fuel jets with air. The configuration investigated in this study is a tubular air passage with fuel injection from one single orifice placed in the side wall. In the range of typical gas turbine combustor inlet temperatures, the performance vortex generator premixers (VGPs) have already been investigated for natural gas as well as for blends of natural gas and hydrogen. However, for highly reactive fuels, the application of VGPs in recuperated gas turbines is particularly challenging because the high combustor inlet temperature leads to potential risk with regard to premature self-ignition and flame flashback. As the current knowledge does not cover the temperature range far above the self-ignition temperature, an experimental investigation of the operational limits of VGPs is currently being conducted at the Thermodynamics Institute of the Technical University of Munich, Garching, Germany, which is particularly focused on reactive fuels and the thermodynamic conditions present in recuperated gas turbines with pressure ratios of 4–5. For the study presented in this paper, an atmospheric combustion VGP test rig has been designed, which facilitates investigations in a wide range of operating conditions in order to comply with the situation in recuperated microgas turbines (MGT), namely, global equivalence ratios between 0.2 and 0.7, air preheating temperatures between 288 K and 1100 K, and air bulk flow rates between 6 and 16 g/s. Both the entire mixing zone in the VGP and the primary combustion zone of the test rig are optically accessible. High-speed OH* chemiluminescence imaging is used for the detection of the flashback and blow-off limits of the investigated VGPs. Flashback and blow-off limits of hydrogen in a wide temperature range covering the autoignition regime are presented, addressing the influences of equivalence ratio, air preheating temperature, and momentum ratio between air and hydrogen on the operational limits in terms of bulk flow velocity. It is shown that flashback and blow-off limits are increasingly influenced by autoignition in the ultrahigh temperature regime.

Operability Limits of Tubular Injectors With Vortex Generators for a Hydrogen Fuelled Recuperated 100kW Class Gas Turbine

2016 ◽  
Author(s):  
Stefan Bauer ◽  
Balbina Hampel ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Bulk Flow ◽  
Vortex Generators ◽  
Test Rig ◽  
Temperature Range ◽  
Auto Ignition ◽  
Wide Range

Vortex generators are known to be effective in augmenting the mixing of fuel jets with air. The configuration investgated in this study is a tubular air passage with fuel injection from one single orifice placed in the side wall. In the range of typical gas turbine combustor inlet temperatures, the performance vortex generator premixers (VGPs) have already been investigated for natural gas as well as for blends of natural gas and hydrogen. However, for highly reactive fuels, the application of VGPs in recuperated gas turbines is particularly challenging because the high combustor inlet temperature leads to potential risk with regard to premature self-ignition and flame flashback. As the current knowledge does not cover the temperature range far above the self-ignition temperature, an experimental investigation of the operational limits of VGPs is currently being conducted at the Thermodynamics Institute of the Technical University of Munich, which is particularly focused on reactive fuels and the thermodynamic conditions present in recuperated gas turbines with pressure ratios of 4–5. For the study presented in the paper, an atmospheric combustion VGP test rig has been designed, which facilitates investigations in a wide range of operating conditions in order to comply with the situation in recuperated micro gas turbines, namely global equivalence ratios between 0.2 and 0.7, air preheating temperatures between 288K and 1100K, and air bulk flow rates between 6–16 g/s. Both the entire mixing zone in the VGP and the primary combustion zone of the test rig are optically accessible. High speed OH* chemiluminescence imaging is used for the detection of the flashback and blow-off limits of the investigated VGPs. Flashback and blow-off limits of hydrogen in a wide temperature range covering the auto-ignition regime are presented, addressing the influences of equivalence ratio, air preheating temperature and momentum ratio between air and hydrogen on the operational limits in terms of bulk flow velocity. It is shown that flashback and blow-off limits are increasingly influenced by auto-ignition in the ultra-high temperature regime.

LNG Vaporization Using a Novel Co-Generation System

2008 ◽  
Author(s):  
H. Griepentrog ◽  
G. Tsatsaronis ◽  
T. Morosuk
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Electricity Generation ◽  
Primary Energy ◽  
Liquefied Natural Gas ◽  
Energy Sources ◽  
Generation System ◽  
Large Share ◽  
Total Cost ◽  
Liquefaction Process

Natural gas is one of the most important primary energy sources. It is expected to account for about 30% of total electricity generation by 2020 compared with 17% in 2000. Liquefied natural gas (LNG) is expected to have a large share in this expansion of use of natural gas. In the last years the total cost of LNG technology has decreased mainly due to improvements in the liquefaction process. The paper discusses some novel, gas-turbine-based concepts for combining LNG regasification with electricity generation. A comparative exergetic evaluation of the concepts is presented.

scholarly journals Volatile, Low Lubricity Fuels in Gas Turbine Plants: A Review of Main Fuel Options and Their Respective Merits

1998 ◽  
Author(s):  
M. Molière ◽  
F. Geiger ◽  
E. Deramond ◽  
T. Becker
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Primary Energy ◽  
Liquid Fuels ◽  
Heavy Duty ◽  
Gas Condensates ◽  
Clear Identification

While natural gas is achieving unrivalled penetration in the power generation sector, especially in gas-turbine combined cycles (CCGT), an increasing number of alternative fuels are in a position to take up the ground left vacant by this major primary energy. In particular, within the thriving family of liquid fuels, the class of volatile products opens interesting prospects for clean and efficient power generation in CCGT plants. Therefore, it has become a necessity for the gas turbine industry to extensively evaluate such new fuel candidates, among which: naphtha’s; kerosines; gas condensates; Natural Gas Liquids (NGL) and alcohols are the most prominent representatives. From a technical standpoint, the success of such projects requires both a careful approach to several specific issues (eg: fuel handling & storage, operation safety) and a clear identification of technological limits. For instance, while the purity of gas condensates meets the requirements of heavy-duty technologies, it generally appears unsuitable for aeroderivative machines. This paper offers a succinct but comprehensive technical approach and overviews some experience acquired in this area with heavy duty gas turbines. Its aim is to inform gas turbine users/engineers and project developers who envisage volatile fuels as alternative primary energies in gas turbine plants.

scholarly journals CFD Modeling of Syngas Combustion and Emissions for Marine Gas Turbine Applications

2016 ◽  
Vol 23 (3) ◽  
pp. 39-49 ◽  
Author(s):  
Nader R. Ammar ◽  
Ahmed I. Farag
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Alternative Fuels ◽  
Flame Temperature ◽  
Operating Conditions ◽  
Cfd Modeling ◽  
Ansys Fluent ◽  
Gas Fuel

Abstract Strong restrictions on emissions from marine power plants will probably be adopted in the near future. One of the measures which can be considered to reduce exhaust gases emissions is the use of alternative fuels. Synthesis gases are considered competitive renewable gaseous fuels which can be used in marine gas turbines for both propulsion and electric power generation on ships. The paper analyses combustion and emission characteristics of syngas fuel in marine gas turbines. Syngas fuel is burned in a gas turbine can combustor. The gas turbine can combustor with swirl is designed to burn the fuel efficiently and reduce the emissions. The analysis is performed numerically using the computational fluid dynamics code ANSYS FLUENT. Different operating conditions are considered within the numerical runs. The obtained numerical results are compared with experimental data and satisfactory agreement is obtained. The effect of syngas fuel composition and the swirl number values on temperature contours, and exhaust gas species concentrations are presented in this paper. The results show an increase of peak flame temperature for the syngas compared to natural gas fuel combustion at the same operating conditions while the NO emission becomes lower. In addition, lower CO2 emissions and increased CO emissions at the combustor exit are obtained for the syngas, compared to the natural gas fuel.

Pentane Rich Fuels for Standard Siemens DLE Gas Turbines

2011 ◽  
Author(s):  
Mats Andersson ◽  
Anders Larsson ◽  
Arturo Manrique Carrera
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combustion Dynamics ◽  
Heating Value ◽  
Special Adaptation ◽  
Fuel Flexibility ◽  
Combustion Properties ◽  
Model Substance ◽  
Wobbe Index

Associated gases at oil wells are often rich in heavy hydrocarbons (HHC, here denoting hydrocarbons heavier than propane). HHC cause handling difficulties and the combustion properties are quite different from standard natural gas. For this and other reasons HHC rich associated gases are often flared or vented. This is an enormous waste of useable energy and a significant contribution to emissions of pollutants, global CO2 and other greenhouse gases. Siemens Industrial Turbomachinery AB in Finspong (SIT AB) recently tested a standard DLE 25 MW SGT-600 gas turbine and a standard 31 MW SGT-700 gas turbine with HHC rich natural gas. Pentane was chosen as a model substance for HHC. The tested gases had up to 30% of the fuel heating value from pentane. The unmodified standard DLE gas turbines proved to be very tolerant to the tested pentane rich gases. CO emissions were reduced with increasing pentane content in the fuel for the same power output. NOx was observed to increase linearly with the pentane content. Combustion dynamics was affected mildly, but noticeably by the pentane rich fuel. This result, together with earlier presented results for the same DLE engines on nitrogen rich natural gases, gives an accepted and tested total LHV range of 25–50 MJ/kg and Wobbe index range of 25–55 MJ/Nm3. No special adaptation of the gas turbines was necessary for allowing this wide fuel range. The benefit of increased and proven fuel flexibility is obvious as it allows the gas turbine owner to make full use of opportunity fuels and to supply power at low fuel cost.

Retrofittable Solutions to Keep Existing Gas Turbine Power Plants Viable and Profitable in an Increasingly Dynamic Power Generation Market: Validation of Low Pressure Drop FlameSheet™ Combustor

2019 ◽  
Author(s):  
Fred Hernandez ◽  
Hany Rizkalla
Keyword(s):  
Power Plant ◽  
Pressure Drop ◽  
Natural Gas ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Load Range ◽  
Pressure Losses ◽  
Fuel Flexibility

Abstract As renewable energy sources continue their global energy market penetration, new natural gas fired power plant installations have decreased significantly. The reduction in new installed capacity has increased pressure on operators to profitably maintain and expand their existing fleet capability. Retrofitting existing gas turbines to increase baseload power output, expand fuel flexibility and provide a wider operating load range are key natural gas fired power plant market demands. The FlameSheet™ combustor system addresses these considerations with a novel “dual-zone burn system” design that reduces emissions, increases fuel flexibility and reduces pressure losses to improve thermal cycle efficiency. The present work presents the results of FlameSheet™ installations into GE 7F.03 heavy duty gas turbines at two commercial sites. The first installation combined FlameSheet™ with PSM’s Gas Turbine Optimization Package (GTOP) to provide higher output through a combination of lower combustor pressure drop, higher mass flows and an increase in firing temperature, while maintaining sub-9ppm NOx emissions across the expanded operating range. Results are also presented for a second site on a unit that operates with up to 5% hydrogen blend into the baseline natural gas, where a reduction in NOx to sub-4 ppm levels at a typical 7F.03 baseload point has been safely and reliably achieved. Both results continue to demonstrate that fuel flexibility and expanded operational windows are possible to “future proof” existing gas turbine installations at a fraction of the cost of a new unit installation.

Sign in / Sign up

Export Citation Format

Share Document