Optimizing Lifetime Consumption and Increasing Flexibility Using Enhanced Lifetime Assessment Methods With Automated Stress Calculation From Long-Term Operation Data

2013 ◽  
Author(s):  
Jan Vogt ◽  
Thomas Schaaf ◽  
Klaus Helbig
Keyword(s):  
Power Plants ◽  
Low Cycle Fatigue ◽  
Combined Cycle ◽  
Transient Temperature ◽  
Steam Turbines ◽  
Transfer Coefficients ◽  
Term Operation ◽  
Flexible Mode ◽  
Start Up ◽  
Safety Margins

In the past most of the steam turbines were designed as base load machines. Due to new market requirements based on the effect of renewable energies, power plant operators are forced to operate with more frequent start-up events and load changes, resulting in a fundamental higher low cycle fatigue (LCF) lifetime consumption. Traditional methods of lifetime assessment often use representative start-ups, for the calculation of LCF damage, which can provide very conservative results with reasonable safety margins. For a high number of starts these safety margins may result in an overestimation of the LCF damage. At Alstom, an enhanced method for lifetime assessment has been developed, that evaluates the actual lifetime consumption from real operation data in an automated manner and provides much more realistic results. The operation data is used to calculate the transient temperature distribution and heat transfer coefficients along the rotor for each start-stop cycle. The corresponding stress distribution in the rotor is evaluated by means of a Finite-Element-method analysis. Finally the number of remaining cycles is extracted for the most critical locations using material data. In combination with the creep damage the lifetime consumption is evaluated. The entire process is highly automated, but also facilitates easy monitoring through the lifetime engineer by graphic presentation of calculation results. Using this enhanced method of lifetime assessment, the computed lifetime consumption is closer to the actual value, supporting the planning of overhauls and component replacements and minimizing the risk of failure or forced outages. The utilization of remaining lifetime can be optimized in favour of a more flexible mode of operation (e.g. low load operation and fast start-up) or extension of operational lifetime for conventional and combined cycle power plants.

Coordinated Control of Gas and Steam Turbines for Efficient Fast Start-Up of Combined Cycle Power Plants

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Yasuhiro Yoshida ◽  
Kazunori Yamanaka ◽  
Atsushi Yamashita ◽  
Norihiro Iyanaga ◽  
Takuya Yoshida
Keyword(s):  
Thermal Stress ◽  
Steam Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Thermal Stresses ◽  
Control Method ◽  
Coordinated Control ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Start Up

In the fast start-up for combined cycle power plants (CCPP), the thermal stresses of the steam turbine rotor are generally controlled by the steam temperatures or flow rates by using gas turbines (GTs), steam turbines, and desuperheaters to avoid exceeding the thermal stress limits. However, this thermal stress sensitivity to steam temperatures and flow rates depends on the start-up sequence due to the relatively large time constants of the heat transfer response in the plant components. In this paper, a coordinated control method of gas turbines and steam turbine is proposed for thermal stress control, which takes into account the large time constants of the heat transfer response. The start-up processes are simulated in order to assess the effect of the coordinated control method. The simulation results of the plant start-ups after several different cool-down times show that the thermal stresses are stably controlled without exceeding the limits. In addition, the steam turbine start-up times are reduced by 22–28% compared with those of the cases where only steam turbine control is applied.

Rotor-Blade Interaction During Blade Resonance Drive-Through

2021 ◽  
Author(s):  
Roland Grein ◽  
Ulrich Ehehalt ◽  
Christian Siewert ◽  
Norbert Kill
Keyword(s):  
Power Plants ◽  
Renewable Energy Sources ◽  
Cyclic Fatigue ◽  
Combined Cycle ◽  
Plant Design ◽  
Steam Turbines ◽  
Rotating Speed ◽  
Start Up ◽  
Blade Vibrations ◽  
Fast Start

Abstract In the future energy landscape, combined cycle power plants will increasingly take the role of providing balancing power for fluctuating renewable energy sources due to their high availability and fast start-up times. This implies more frequent cycling, a larger number of speed cycles and thus new challenges for plant design and operation. One of these challenges is a potential increase of cyclic fatigue incurred by last-stage blades during start-up and coast-down. Blade vibrations might be induced by synchronous shaft vibrations when the blade resonance is excited by lateral shaft vibrations. In this paper, we report measurement results of shaft and blade vibrations observed at some Siemens Energy steam turbines. Apart from the expected increase of blade vibrations when the double rotating speed crosses the blade resonance, a distinctive dip of shaft vibrations at the low-pressure turbine bearings is observed. We argue that this phenomenon is likely related to the aforementioned interaction between blade and shaft vibrations and present a theoretical framework to describe this interaction and the observed effect.

State of the Art Steam Turbine Automation for Optimum Transient Operation Performance

2007 ◽  
Author(s):  
Rainer Quinkertz ◽  
Edwin Gobrecht
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Operation Performance ◽  
Control Functions ◽  
Steam Power Plants ◽  
Start Up ◽  
Full Speed ◽  
Startup Performance

The growing share of renewable energies in the power industry coupled with increased deregulation has led to the need for additional operating flexibility of steam turbine units in both Combined Cycle and Steam Power Plants. Siemens steam turbine engineering and controls presently have several solutions to address various operating requirements: - Use of an automatic step program to perform startups allows operating comfort and repeatability. - 3 start-up modes give the operator the flexibility to start quickly to meet demand or slowly to conserve turbine life. - Several options for lifetime management are available. These options range from a basic counter of equivalent operating hours to a detailed fatigue calculation. - Restarting capabilities have been improved to allow a faster response following a trip or shutdown. - In addition to control of speed, load and pressure, special control functions provide alternative work split modes during transient conditions. - Optimum steam temperatures are calculated by the steam turbine control system to achieve optimum startup performance. - Siemens steam turbines are also capable of load rejection to house load, some even to operation at full speed, no load. Several plants are already equipped with these solutions and have provided data showing they are operating with shorter start-up times and improved load rejection capabilities. Finally Siemens of course continues to pursue future development.

Component Low Cycle Fatigue Behavior Based on Standard Calculation Procedure and Non-Linear FEA

2017 ◽  
Author(s):  
Jürgen Rudolph ◽  
Adrian Willuweit ◽  
Steffen Bergholz ◽  
Christian Philippek ◽  
Jevgenij Kobzarev
Keyword(s):  
Power Plants ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Hybrid Approach ◽  
Combined Cycle ◽  
Cycle Fatigue ◽  
Element Analysis ◽  
Constitutive Material Model ◽  
Standard Design ◽  
Creep Fatigue

Components of conventional power plants are subject to potential damage mechanisms such as creep, fatigue and their combination. These mechanisms have to be considered in the mechanical design process. Against this general background — as an example — the paper focusses on the low cycle fatigue behavior of a main steam shut off valve. The first design check based on standard design rules and linear Finite Element Analysis (FEA) identifies fatigue sensitive locations and potentially high fatigue usage. This will often occur in the context of flexible operational modes of combined cycle power plants which are a characteristic of the current demands of energy supply. In such a case a margin analysis constitutes a logical second step. It may comprise the identification of a more realistic description of the real operational loads and load-time histories and a refinement of the (creep-) fatigue assessment methods. This constitutes the basis of an advanced component design and assessment. In this work, nonlinear FEA is applied based on a nonlinear kinematic constitutive material model, in order to simulate the thermo-mechanical behavior of the high-Cr steel component mentioned above. The required material parameters are identified based on data of the accessible reference literature and data from an own test series. The accompanying testing campaign was successfully concluded by a series of uniaxial thermo-mechanical fatigue (TMF) tests simulating the most critical load case of the component. This detailed and hybrid approach proved to be appropriate for ensuring the required lifetime period of the component.

Repowering and Retrofitting

2002 ◽  
Author(s):  
Andreas Pickard
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Free Market ◽  
Leading Edge ◽  
Project Planning ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Planning Stage ◽  
Reheat Steam ◽  
Plant Optimization

At the start of this new century, environmental regulations and free-market economics are becoming the key drivers for the electricity generating industry. Advances in Gas Turbine (GT) technology, allied with integration and refinement of Heat Recovery Steam Generators (HRSG) and Steam Turbine (ST) plant, have made Combined Cycle installations the most efficient of the new power station types. This potential can also be realized, to equal effect, by adding GT’s and HRSG’s to existing conventional steam power plants in a so-called ‘repowering’ process. This paper presents the economical and environmental considerations of retrofitting the steam turbine within repowering schemes. Changing the thermal cycle parameters of the plant, for example by deletion of the feed heating steambleeds or by modified live and reheat steam conditions to suit the combined cycle process, can result in off-design operation of the existing steam turbine. Retrofitting the steam turbine to match the combined cycle unit can significantly increase the overall cycle efficiency compared to repowering without the ST upgrade. The paper illustrates that repowering, including ST retrofitting, when considered as a whole at the project planning stage, has the potential for greater gain by allowing proper plant optimization. Much of the repowering in the past has been carried out without due regard to the benefits of re-matching the steam turbine. Retrospective ST upgrade of such cases can still give benefit to the plant owner, especially when it is realized that most repowering to date has retained an unmodified steam turbine (that first went into operation some decades before). The old equipment will have suffered deterioration due to aging and the steam path will be to an archaic design of poor efficiency. Retrofitting older generation plant with modern leading-edge steam-path technology has the potential for realizing those substantial advances made over the last 20 to 30 years. Some examples, given in the paper, of successfully retrofitted steam turbines applied in repowered plants will show, by specific solution, the optimization of the economics and benefit to the environment of the converted plant as a whole.

Investigation Into the Thermal Limitations of Steam Turbines During Start-Up Operation

2017 ◽  
Author(s):  
Monika Topel ◽  
Björn Laumert ◽  
Åsa Nilsson ◽  
Markus Jöcker
Keyword(s):  
Electricity Market ◽  
Low Cycle Fatigue ◽  
Operating Conditions ◽  
Limiting Factor ◽  
Steam Turbines ◽  
Expansion Behavior ◽  
Start Up ◽  
Schedule Design ◽  
Turbine Component ◽  
Differential Expansion

Liberalized electricity market conditions and concentrating solar power technologies call for increased power plant operational flexibility. Concerning the steam turbine component, one key aspect of its flexibility is the capability for fast starts. In current practice, turbine start-up limitations are set by consideration of thermal stress and low cycle fatigue. However, the pursuit of faster starts raises the question whether other thermal phenomena can become a limiting factor to the start-up process. Differential expansion is one of such thermal properties, especially since the design of axial clearances is not included as part of start-up schedule design and because its measurement during operation is often limited or not a possibility at all. The aim of this work is to understand differential expansion behavior with respect to transient operation and to quantify the effect that such operation would have in the design and operation of axial clearances. This was accomplished through the use of a validated thermo-mechanical model that was used to compare differential expansion behavior for different operating conditions of the machine. These comparisons showed that faster starts do not necessarily imply that wider axial clearances are needed, which means that the thermal flexibility of the studied turbine is not limited by differential expansion. However, for particular locations it was also obtained that axial rubbing can indeed become a limiting factor in direct relation to start-up operation. The resulting approach presented in this work serves to avoid over-conservative limitations in both design and operation concerning axial clearances.

A Study on the Temperature Calibration for a Small Electrical Resistance Furnace

2010 ◽  
Author(s):  
Un Bong Baek ◽  
Hae Moo Lee ◽  
Yun-Hee Lee ◽  
Seung Hoon Nahm
Keyword(s):  
Electrical Resistance ◽  
Power Plants ◽  
Low Cycle Fatigue ◽  
Small Scale ◽  
Temperature Calibration ◽  
Cycle Fatigue ◽  
Resistance Furnace ◽  
Small Space ◽  
Start Up ◽  
Electrical Resistance Furnace

A severe thermal stress occurs during start up/shutdown transients in thick walled components of high temperature power plants. Thus, a precise consideration of this issue is very important. Many researchers have studied low-cycle fatigue at high temperatures and small box-type electrical resistance furnaces have been developed for small-sized fatigue specimens. However, these small-scale electrical resistance furnaces need precise temperature calibrations because temperature control is difficult in a small space. Thus, a method for the temperature calibration of a box-type electrical resistance furnace is investigated and calibration procedures are proposed in this study.

scholarly journals Determination of Transient Fluid Temperature and Thermal Stresses in Pressure Thick-Walled Elements Using a New Design Thermometer

Energies ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 222 ◽  
Author(s):  
Magdalena Jaremkiewicz ◽  
Dawid Taler ◽  
Piotr Dzierwa ◽  
Jan Taler
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Critical Pressure ◽  
Thermal Stresses ◽  
Thermal Inertia ◽  
Internal Surface ◽  
Transient Temperature ◽  
Fluid Temperature ◽  
Start Up

In both conventional and nuclear power plants, the high thermal load of thick-walled elements occurs during start-up and shutdown. Therefore, thermal stresses should be determined on-line during plant start-up to avoid shortening the lifetime of critical pressure elements. It is necessary to know the fluid temperature and heat transfer coefficient on the internal surface of the elements, which vary over time to determine transient temperature distribution and thermal stresses in boilers critical pressure elements. For this reason, accurate measurement of transient fluid temperature is very significant, and the correct determination of transient thermal stresses depends to a large extent on it. However, thermometers used in power plants are not able to measure the transient fluid temperature with adequate accuracy due to their massive housing and high thermal inertia. The article aims to present a new technique of measuring transient superheated steam temperature and the results of its application on a real object.

Modeless Start-Up Control for Operational Flexibility of Combined Cycle Power Plants

2020 ◽  
Vol 53 (10) ◽  
pp. 636-645
Author(s):  
Yasuhiro Yoshida ◽  
Yuya Tokuda ◽  
Takuya Yoshida ◽  
Yuki Enomoto ◽  
Nobuhiro Osaki ◽  
...  
Keyword(s):  
Power Plants ◽  
Combined Cycle ◽  
Operational Flexibility ◽  
Start Up
Sign in / Sign up

Export Citation Format

Share Document