Effects of Endwall 3D Contouring on Film Cooling Effectiveness of Cylindrical Hole Injections at Different Locations on Vane Endwall

2018 ◽  
Author(s):  
Pingting Chen ◽  
Hongyu Gao ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Secondary Flows ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Endwall Contouring

With the development of gas turbine, the secondary flow loss in vane passage is getting higher. To reduce the strength of secondary flows within vane passage, endwall 3D contouring is an effective design. Endwall 3D contouring can lead to significant changes in the secondary flow vortices, which lead to changes on jet-to-secondary flow interaction and then changes on the film cooling effectiveness. Meanwhile, the geometry configuration of the contoured endwall, such as the rising and falling on the endwall, can also have an impact on film cooling performance. As a result, the film cooling performance on contoured endwall differs from that on flat endwall. Understanding the difference in film cooling characteristics on the contoured endwall and flat endwall may help to make better endwall contouring design and better endwall film cooling arrangement. The present experiment compares the film cooling effectiveness of cylindrical hole injections at different locations on 3D contoured endwall versus flat endwall in an NGV (nozzle guide vane) passage. The measurement is performed in a low speed wind tunnel with a F-class annular sector NGV cascade. The cylindrical hole injections are located as 4 different rows at −30% axial chord, 30% axial chord, 50% axial chord and 70% axial chord. Endwall pressure distribution is measured with pressure taps by pressure sensor while film cooling effectiveness is measured using PSP (Pressure Sensitive Paint). Two density ratios with 1.0 and 1.5 and several average blowing ratios are investigated. Effects of endwall contouring, density ratio and blowing ratio on film cooling effectiveness are obtained and the results are presented and explained in this investigation.

Assessment of a Double Hole Film Cooling Geometry Using S-PIV and PSP

2013 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Charles P. Brown ◽  
Weston V. Harmon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Three Dimensional ◽  
Field Measurements ◽  
Secondary Flows ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Hole Geometry ◽  
Compound Angle

A novel, double hole film cooling configuration is investigated as an alternative to traditional cylindrical and fanshaped, laidback holes. This experimental investigation utilizes a Stereo-Particle Image Velocimetry (S-PIV) to quantitatively assess the ability of the proposed, double hole geometry to weaken or mitigate the counter-rotating vortices formed within the jet structure. The three-dimensional flow field measurements are combined with surface film cooling effectiveness measurements obtained using Pressure Sensitive Paint (PSP). The double hole geometry consists of two compound angle holes. The inclination of each hole is θ = 35°, and the compound angle of the holes is β = ± 45° (with the holes angled toward one another). The simple angle cylindrical and shaped holes both have an inclination angle of θ = 35°. The blowing ratio is varied from M = 0.5 to 1.5 for all three film cooling geometries while the density ratio is maintained at DR = 1.0. Time averaged velocity distributions are obtained for both the mainstream and coolant flows at five streamwise planes across the fluid domain (x/d = −4, 0, 1, 5, and 10). These transverse velocity distributions are combined with the detailed film cooling effectiveness distributions on the surface to evaluate the proposed double hole configuration (compared to the traditional hole designs). The fanshaped, laidback geometry effectively reduces the strength of the kidney-shaped vortices within the structure of the jet (over the entire range of blowing ratios considered). The three-dimensional velocity field measurements indicate the secondary flows formed from the double hole geometry strengthen in the plane perpendicular to the mainstream flow. At the exit of the double hole geometry, the streamwise momentum of the jets is reduced (compared to the single, cylindrical hole), and the geometry offers improved film cooling coverage. However, moving downstream in the steamwise direction, the two jets form a single jet, and the counter-rotating vortices are comparable to those formed within the jet from a single, cylindrical hole. These strong secondary flows lift the coolant off the surface, and the film cooling coverage offered by the double hole geometry is reduced.

Turbine Vane Endwall Film Cooling With Slashface Leakage and Discrete Hole Configuration

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Secondary Flows ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Leakage Flows ◽  
Turbine Vane

Turbine vanes are typically assembled as a section containing single or double airfoil units in an annular pattern. First stage guide vane assembly results in two common mating interfaces: a gap between combustor and vane endwall and another resulted from the adjacent sections, called slashface. High pressure coolant could leak through these gaps to reduce the ingestion of hot gas and achieve certain cooling benefit. As vane endwall region flow field is already very complicated due to highly three-dimensional secondary flows, then a significant influence on endwall cooling can be expected due to the gap leakage flows. To determine the effect of leakage flows from those gaps, film cooling effectiveness distributions were measured using pressure sensitive paint (PSP) technique on the endwall of a scaled up, midrange industrial turbine vane geometry with the multiple rows of discrete film cooling (DFC) holes inside the passages. Experiments were performed in a blow-down wind tunnel cascade facility at the exit Mach number of 0.5 corresponding to Reynolds number of 3.8 × 105 based on inlet conditions and axial chord length. Passive turbulence grid was used to generate free-stream turbulence (FST) level about 19% with an integral length scale of 1.7 cm. Two parameters, coolant-to-mainstream mass flow ratio (MFR) and density ratio (DR), were studied. The results are presented as two-dimensional film cooling effectiveness distribution on the vane endwall surface with the corresponding spanwise averaged values along the axial direction.

Comparison of Film Cooling Performance for Different Purge Slot Configurations in a Cylindrical and State-of-the-Art Nozzle Guide Vane

2021 ◽  
Author(s):  
Christian Landfester ◽  
Gunther Müller ◽  
Robert Krewinkel ◽  
Clemens Domnick ◽  
Martin Böhle
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on the film cooling performance by injecting coolant through the purge slot. An experimental study compares the film cooling effectiveness as well as the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with four cylindrical vanes, the contoured endwall cascade consisted of four modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the purge slot width and injection angle, as well as different blowing ratios (BR) at an engine-like density ratio (DR = 1.6) were realized to investigate the real-life effect of thermal expansion, design modifications and the interaction between secondary flow and coolant. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. The Pressure Sensitive Paint (PSP) technique was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements (DR = 1.0) were performed to measure the flow field with its characteristic vortex structures as well as the loss distribution in the vane wake region. For a more profound insight into the origin and development of the secondary flows, oil dye visualizations were carried out on both endwalls. The measurement results will be discussed based on a side-by-side comparison of the distribution of film cooling effectiveness on the endwall, its area-averaged values as well as the two-dimensional distribution of total pressure losses and the secondary flow field. The results of this study show that the advances in NGV design development have had a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. In contrast to the results of the cylindrical profile, sufficient cooling can be already provided with a perpendicular injection in the case of the modern NGV. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Turbine Vane Endwall Film Cooling Effectiveness of Different Purge Slot Configurations in a Linear Cascade

2020 ◽  
Vol 142 (3) ◽  
Author(s):  
Gunther Müller ◽  
Christian Landfester ◽  
Martin Böhle ◽  
Robert Krewinkel
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Experimental Tests ◽  
Secondary Flows ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Density Ratios ◽  
Endwall Film Cooling

Abstract This study is concerned with the film cooling effectiveness of the flow issuing from the gap between the nozzle guide vane (NGV) and the transition duct on the NGV endwall, i.e., the purge slot. Different slot widths, positions, and injection angles were examined in order to represent changes due to thermal expansion as well as design modifications. Apart from these geometric variations, different blowing ratios (BRs) and density ratios (DRs) were realized to investigate the effects of the interaction between secondary flow and film cooling effectiveness. The experimental tests were performed in a linear scale-1 cascade equipped with four highly loaded turbine vanes at the Institute of Fluid Mechanics and Fluid Machinery of the University of Kaiserslautern. The mainstream flow parameters were, with a Reynolds number of 300,000 and a Mach number (outlet) of 0.6, set to meet real engine conditions. By using various flow conditioners, periodic flow was obtained in the region of interest (ROI). The adiabatic film cooling effectiveness was determined using the pressure sensitive paint (PSP) technique. In this context, nitrogen and carbon dioxide were used as tracer gases realizing two different density ratios DR = 1.0 and 1.6. The investigation was conducted for a broad range of blowing ratios with 0.25 ≤ BR ≤ 1.50. In combination with 10 geometry variations and the aforementioned blowing and density ratio variations, 100 single operating points were investigated. For a better understanding of the coolant distribution, the secondary flows on the endwall were visualized by oil dye. The measurement results will be discussed based on the areal distribution of film cooling effectiveness, its lateral spanwise, as well as its area average. The results will provide a better insight into various parametric effects of gap variations on turbine vane endwall film cooling performance—notably under realistic engine conditions.

Turbine Vane Endwall Film Cooling With Slashface Leakage and Discrete Hole Configuration

2016 ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Secondary Flows ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Leakage Flows ◽  
Turbine Vane ◽  
Inlet Conditions

Turbine vanes are typically assembled as a section containing single or double airfoil units in an annular pattern. First stage guide vane assembly results in two common mating interfaces — a gap between combustor and vane endwall and another resulted from the adjacent sections, called slashface. High pressure coolant could leak through these gaps to reduce the ingestion of hot gas and achieve certain cooling benefit. As vane endwall region flow field is already very complicated due to highly three-dimensional secondary flows, then a significant influence on endwall cooling can be expected due to the gap leakage flows. To determine the effect of leakage flows from those gaps, film cooling effectiveness distributions were measured using Pressure Sensitive Paint (PSP) technique on the endwall of a scaled up, mid-range industrial turbine vane geometry with the multiple rows of discrete film cooling holes inside the passages. Experiments were performed in a blow-down wind tunnel cascade facility at the exit Mach number of 0.5 corresponding to Reynolds number of 3.8 × 105 based on inlet conditions and axial chord length. Passive turbulence grid was used to generate freestream turbulence level about 19% with an integral length scale of 1.7 cm. Two parameters, coolant-to-mainstream mass flow ratio and density ratio were studied. The results are presented as two-dimensional film cooling effectiveness distribution on the vane endwall surface and the corresponding spanwise averaged values along the axial direction are also demonstrated.

Film Cooling Performance of Tripod Antivortex Injection Holes Over the Pressure and Suction Surfaces of a Nozzle Guide Vane

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
Sridharan Ramesh ◽  
Christopher LeBlanc ◽  
Diganta Narzary ◽  
Srinath Ekkad ◽  
Mary Anne Alvin
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Nozzle Guide

Film cooling performance of the antivortex (AV) hole has been well documented for a flat plate. The goal of this study is to evaluate the same over an airfoil at three different locations: leading edge suction and pressure surface and midchord suction surface. The airfoil is a scaled up first stage vane from GE E3 engine and is mounted on a low-speed linear cascade wind tunnel. Steady-state infrared (IR) technique was employed to measure the adiabatic film cooling effectiveness. The study has been divided into two parts: the initial part focuses on the performance of the antivortex tripod hole compared to the cylindrical (CY) hole on the leading edge. Effects of blowing ratio (BR) and density ratio (DR) on the performance of cooling holes are studied here. Results show that the tripod hole clearly provides higher film cooling effectiveness than the baseline cylindrical hole case with overall reduced coolant usage on the both pressure and suction sides of the airfoil. The second part of the study focuses on evaluating the performance on the midchord suction surface. While the hole designs studied in the first part were retained as baseline cases, two additional geometries were also tested. These include cylindrical and tripod holes with shaped (SH) exits. Film cooling effectiveness was found at four different blowing ratios. Results show that the tripod holes with and without shaped exits provide much higher film effectiveness than cylindrical and slightly higher effectiveness than shaped exit holes using 50% lesser cooling air while operating at the same blowing ratios. Effectiveness values up to 0.2–0.25 are seen 40-hole diameters downstream for the tripod hole configurations, thus providing cooling in the important trailing edge portion of the airfoil.

Numerical Investigation of the Cooling Performance on the Endwall With and Without Fillet

2018 ◽  
Author(s):  
Qingzong Xu ◽  
Qiang Du ◽  
Pei Wang ◽  
Jun Liu ◽  
Guang Liu
Keyword(s):  
Secondary Flow ◽  
Turbulence Model ◽  
Film Cooling ◽  
Computational Method ◽  
Inlet Temperature ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Numerical Predictions ◽  
Turbine Vane

High inlet temperature of turbine vane increases the demand of high film cooling effectiveness. Vane endwall region was extensively cooled due to the high and flat exit temperature distribution of combustor. Leakage flow from the combustor-turbine gap was used to cool the endwall region except for preventing hot gas ingestion. Numerical predictions were conducted to investigate the flow structure and adiabatic film cooling effectiveness of endwall region in a linear cascade with vane-endwall junction fillet. The simulations were completed by solving the three-dimensional Reynolds-Averaged Navier-Stokes(RANS) equations with shear stress transport(SST) k-ω turbulence model, meanwhile, the computational method and turbulence model were validated by comparing computational result with the experiment. Three types of linear fillet with the length-to-height ratio of 0.5, 1 and 2, named fillet A, fillet B and fillet C respectively, were studied. In addition, circular fillet with radius of 2mm was compared with linear fillet B. The interrupted slot, produced by changing the way of junction of combustor and turbine vane endwall, is introduced at X/Cax = −0.2 upstream of the vane leading edge. Results showed that fillet can significantly affect the cooling performance on the endwall due to suppressing the strength of the secondary flow. Fillet C presented the best cooling performance comparing to fillet A and fillet B because a portion of the coolant which climbs to the fillet was barely affected by secondary flow. Results also showed the effect of fillet on the total pressure loss. The result indicated that only fillet A slightly decreases endwall loss.

Film Cooling of the Gas Turbine Endwall by Discrete-Hole Injection

1996 ◽  
Vol 118 (2) ◽  
pp. 278-284 ◽  
Author(s):  
M. Y. Jabbari ◽  
K. C. Marston ◽  
E. R. G. Eckert ◽  
R. J. Goldstein
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Reynolds Numbers ◽  
Hole Injection ◽  
Qualitative Information ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Density Ratios

Film cooling performance for injection through discrete holes in the endwall of a turbine blade is investigated. The effectiveness is measured at 60 locations in the region covered by injection. Three nominal blowing rates, two density ratios, and two approaching flow Reynolds numbers are examined. Analysis of the data reveals that even 60 locations are insufficient for the determination of the field of film cooling effectiveness with its strong local variations. Visualization of the traces of the coolant jets on the endwall surface, using ammonium-diazo-paper, provides useful qualitative information for the interpretation of the measurements, revealing the paths and interaction of the jets, which change with blowing rate and density ratio.

Injection Angle Influence of Secondary Holes on the Enhancement of Film Cooling Effectiveness With Horn-Shaped or Cylindrical Primary Holes

2017 ◽  
Author(s):  
Rui Zhu ◽  
Gongnan Xie ◽  
Terrence W. Simon
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Inclination Angles ◽  
Cooling Hole ◽  
Cylindrical Holes

Secondary holes to a main film cooling hole are used to improve film cooling performance by creating anti-kidney vortices. The effects of injection angle of the secondary holes on both film cooling effectiveness and surrounding thermal and flow fields are investigated in this numerical study. Two kinds of primary hole shapes are adopted. One is a cylindrical hole, the other is a horn-shaped hole which is designed from a cylindrical hole by expanding the hole in the transverse direction to double the hole size at the exit. Two smaller cylindrical holes, the secondary holes, are located symmetrically about the centerline and downstream of the primary hole. Three compound injection angles (α = 30°, 45° and 60°, β = 30°) of the secondary holes are analyzed while the injection angle of the primary hole is kept at 45°. Cases with various blowing ratios are computed. It is shown from the simulation that cooling effectiveness of secondary holes with a horn-shaped primary hole is better than that with a cylindrical primary hole, especially at high blowing ratios. With a cylindrical primary hole, increasing inclination angle of the secondary holes provides better cooling effectiveness because the anti-kidney vortices created by shallow secondary holes cannot counteract the kidney vortex pairs adequately, enhancing mixing of main flow and coolant. For secondary holes with a horn-shaped primary hole, large secondary hole inclination angles provide better cooling performance at low blowing ratios; but, at high blowing ratios, secondary holes with small inclination angles are more effective, as the film coverage becomes wider in the downstream area.

An Experimental Study of the Leakage Flow Effect on the Film Cooling Effectiveness of a Gas Turbine Shroud

2021 ◽  
pp. 1-18
Author(s):  
Gi Mun Kim ◽  
Soo In Lee ◽  
Jin Young Jeong ◽  
Jae Su Kwak ◽  
Seokbeom Kim ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Density Ratio ◽  
Secondary Flows ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
High Heat Transfer ◽  
Hole Configuration ◽  
Cooling Hole

Abstract In the vicinity of gas turbine blades, a complex flow field is formed due to the flow separation, reattachment, and secondary flows, and this results in a locally non-uniform and high heat transfer on the surfaces. The present study experimentally investigates the effects of leakage flow through the slot between the gas turbine vane and blade rows on the film cooling effectiveness of the forward region of the shroud ring segment. The experiment is carried out in a linear cascade with five blades. Instead of the vane, a row of rods at the location of the vane trailing edge is installed to consider the wake effect. The leakage flow is introduced through the slot between the vane and blade rows, and additional coolant air is injected from the cooling holes installed at the vane's outer zone. The effects of the slot geometry, cooling hole configuration, and blowing ratio on the film cooling effectiveness are experimentally investigated using the pressure sensitive paint (PSP) technique. CO2 gas and a mixture of SF6 and N2 (25%+75%) are used to simulate the leakage flow to the mainstream density ratios of 1.5 and 2.0, respectively. The results indicate that the area averaged film cooling effectiveness is affected more by the slot width than by the cooling hole configuration at the same injection conditions, and the lower density ratio cases show higher film cooling effectiveness than the higher density ratio case at the same cooling configuration.

Sign in / Sign up

Export Citation Format

Share Document