Entropy Generation Analysis of Mixed Convection Flow in a Nanofluid Filled Porous Cavity Using a Two-Component Lattice Boltzmann Method

2019 ◽  
Author(s):  
Dhrubajyoti Kashyap ◽  
Anoop K. Dass
Keyword(s):  
Heat Transfer ◽  
Boundary Conditions ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Lattice Boltzmann ◽  
Lattice Boltzmann Model ◽  
Convection Flow ◽  
Mixed Convection Flow ◽  
Two Phase ◽  
Good Concordance

Abstract In the present work, a comprehensive analysis is made to understand the effect of velocity boundary conditions on the flow and thermal behaviour during mixed convection flow in a nanofluid-saturated porous square cavity. Two different velocity boundary conditions based on the movement of horizontal walls of the cavity are considered. The vertical fixed walls are differentially heated and the horizontal lids are thermally insulated. We have adopted the two-phase thermal lattice Boltzmann model (TLBM) for nanofluid system and modified this model to simulate nanofluid-filled porous medium by incorporating the Brinkman–Forchheimer-extended Darcy model. The current results provide good concordance with the published results computed through conventional numerical techniques. The detailed study of the heat transfer rate, entropy generation is made for discretely varying Richardson numbers (Ri) from 0.1 to 10 and Darcy numbers (Da) from 10−4 to 10−2 while maintaining Grashof number (Gr) at 104 and volume fractions of Cu nanoparticle (ϕ) less than equal to 5%. It is observed from the results that the optimal flow condition in terms of energy efficiency depends on the values of Ri and Da. From the viewpoint of both 1st and 2nd laws of thermodynamics, the performance of nanofluid is not satisfactory compared to the base fluid for current configurations as the augmentation of entropy generation with ϕ is more prominent compared to heat transfer enhancement.

Effect of Nanofluid on Heat Transfer Enhancement for Mixed Convection Flow Over a Corrugated Surface

2020 ◽  
Vol 45 (4) ◽  
pp. 373-383
Author(s):  
Nepal Chandra Roy ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Thermal Boundary Layer ◽  
Volume Fraction ◽  
Convection Flow ◽  
Mixed Convection Flow

AbstractA mathematical model for mixed convection flow of a nanofluid along a vertical wavy surface has been studied. Numerical results reveal the effects of the volume fraction of nanoparticles, the axial distribution, the Richardson number, and the amplitude/wavelength ratio on the heat transfer of Al2O3-water nanofluid. By increasing the volume fraction of nanoparticles, the local Nusselt number and the thermal boundary layer increases significantly. In case of \mathrm{Ri}=1.0, the inclusion of 2 % and 5 % nanoparticles in the pure fluid augments the local Nusselt number, measured at the axial position 6.0, by 6.6 % and 16.3 % for a flat plate and by 5.9 % and 14.5 %, and 5.4 % and 13.3 % for the wavy surfaces with an amplitude/wavelength ratio of 0.1 and 0.2, respectively. However, when the Richardson number is increased, the local Nusselt number is found to increase but the thermal boundary layer decreases. For small values of the amplitude/wavelength ratio, the two harmonics pattern of the energy field cannot be detected by the local Nusselt number curve, however the isotherms clearly demonstrate this characteristic. The pressure leads to the first harmonic, and the buoyancy, diffusion, and inertia forces produce the second harmonic.

Sign in / Sign up

Export Citation Format

Share Document