Modeling Strategy and Numerical Validation for a Darrieus Vertical Axis Micro-Wind Turbine

2010 ◽  
Author(s):  
Marco Raciti Castelli ◽  
Guido Ardizzon ◽  
Lorenzo Battisti ◽  
Ernesto Benini ◽  
Giorgio Pavesi
Keyword(s):  
Wind Turbine ◽  
Recirculation Zone ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Cfd Analysis ◽  
Mesh Quality ◽  
Induced Drag ◽  
Node Distribution ◽  
Spatial Grid ◽  
Modeling Strategy

This paper presents a model for the evaluation of optimal spatial grid node distribution in the CFD analysis of a Darrieus vertical axis micro wind turbine, by analyzing the trends over a 360° rotation of some indicators of near-blade mesh quality. To this purpose, a complete validation campaign has been conducted through a systematic comparison of numerical simulations with wind tunnel experimental data. Both two-dimensional and three-dimensional grids, characterized by average y+ values of 30 and 1, have been tested by applying some statistical techniques as a guidance in selecting the appropriate grid configuration and corresponding turbulence model. Finally, the tip downstream recirculation zone due to the finite blade extension and the influence of spokes have been analyzed, achieving a numerical quantification of the influence of induced drag and spokes drag on overall rotor performance.

scholarly journals CFD ANALYSIS OF THE AIR FLOW AROUND THE BLADES OF THE VERTICAL AXIS WIND TURBINE

2017 ◽  
Vol 3 (1) ◽  
pp. 1-7
Author(s):  
Muhammed Musab Gavgali ◽  
Zbigniew Czyż ◽  
Jacek Czarnigowski
Keyword(s):  
Wind Turbine ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Turbine Rotor ◽  
Rotor Blades ◽  
Cfd Analysis ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Bladed Rotor ◽  
The Individual

The paper presents the results of calculations of flow around the vertical axis wind turbine. Three-dimensional calculations were performed using ANSYS Fluent. They were made at steady-state conditions for a wind speed of 3 m/s for 4 angular settings of the three-bladed rotor. The purpose of the calculations was to determine the values of the aerodynamic forces acting on the individual blades and to present the pressure contours on the surface of turbine rotor blades. The calculations were made for 4 rotor angular settings

Performance enhancement of Savonius wind turbine by blade shape and twisted angle modifications

2021 ◽  
pp. 095765092098794
Author(s):  
Ahmed M Nagib Elmekawy ◽  
Hassan A Hassan Saeed ◽  
Sadek Z Kassab
Keyword(s):  
Wind Turbine ◽  
Performance Enhancement ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Vertical Axis ◽  
Cfd Simulations ◽  
Sliding Mesh ◽  
Blade Shape ◽  
Rotor Shape ◽  
Twisting Angle

Three-dimensional CFD simulations are carried out to study the increase of power generated from Savonius vertical axis wind turbines by modifying the blade shape and blade angel of twist. Twisting angle of the classical blade are varied and several proposed novel blade shapes are introduced to enhance the performance of the wind turbine. CFD simulations have been performed using sliding mesh technique of ANSYS software. Four turbulence models; realizable k -[Formula: see text], standard k - [Formula: see text], SST transition and SST k -[Formula: see text] are utilized in the simulations. The blade twisting angle has been modified for the proposed dimensions and wind speed. The introduced novel blade increased the power generated compared to the classical shapes. The two proposed novel blades achieved better power coefficients. One of the proposed models achieved an increase of 31% and the other one achieved 32.2% when compared to the classical rotor shape. The optimum twist angel for the two proposed models achieved 5.66% and 5.69% when compared with zero angle of twist.

scholarly journals Design and 3D CFD Static Performance Study of a Two-Blade IceWind Turbine

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5356
Author(s):  
Hamdy Mansour ◽  
Rola Afify
Keyword(s):  
Wind Turbine ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Scale Model ◽  
Vertical Axis Wind Turbine ◽  
Performance Study ◽  
Static Performance ◽  
New Type ◽  
Torque Values ◽  
Static Torque

The IceWind turbine, a new type of Vertical Axis Wind Turbine, was proposed by an Iceland based startup. It is a product that has been featured in few published scientific research studies. This paper investigates the IceWind turbine’s performance numerically. Three-dimensional numerical simulations are conducted for the full scale model using the SST K-ω model at a wind speed of 15.8 m/s. The following results are documented: static torque, velocity distributions and streamlines, and pressure distribution. Comparisons with previous data are established. Additionally, comparisons with the Savonius wind turbine in the same swept area are conducted to determine how efficient the new type of turbine is. The IceWind turbine shows a similar level of performance with slightly higher static torque values. Vortices behind the IceWind turbine are confirmed to be three-dimensional and are larger than those of Savonius turbine.

Effect of Blade Inclination Angle on a Darrieus Wind Turbine

2010 ◽  
Author(s):  
Marco Raciti Castelli ◽  
Ernesto Benini
Keyword(s):  
Wind Turbine ◽  
Inclination Angle ◽  
Vertical Axis ◽  
Energy Performance ◽  
Vertical Axis Wind Turbine ◽  
Azimuthal Position ◽  
Induced Drag ◽  
Axial Forces ◽  
Phase Shift Angle ◽  
Modeling Software

This paper presents a model for the evaluation of energy performance and aerodynamic forces acting on a small helical Darrieus vertical axis wind turbine depending on blade inclination angle. It consists of an analytical code coupled to a solid modeling software, capable of generating the desired blade geometry depending on the desired design geometric parameters, which is linked to a finite volume CFD code for the calculation of rotor performance. After describing and validating the model with experimental data, the results of numerical simulations are proposed on the bases of five machine architectures, which are characterized by an inclination of the blades with respect to the horizontal plane in order to generate a phase shift angle between lower and upper blade sections of 0°, 30°, 60°, 90° and 120° for a rotor having an aspect ratio of 1.5. The effects of blade inclination on tangential and axial forces are first discussed and then the overall rotor torque is considered as a function of azimuthal position of the blades. Finally, the downstream tip recirculation zone due to the finite blade extension is analyzed for each blade inclination angle, achieving a numerical quantification of the influence of induced drag on rotor performance, as a function of both blade element longitudinal and azimuthal positions of the blade itself.

Comparative CFD analysis of Vertical Axis Wind Turbine in upright and tilted configuration

2016 ◽  
Vol 85 ◽  
pp. 327-337 ◽  
Author(s):  
Abdullah Mobin Chowdhury ◽  
Hiromichi Akimoto ◽  
Yutaka Hara
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Cfd Analysis ◽  
Vertical Axis Wind Turbine

Three-dimensional flow field around and downstream of a subscale model rotating vertical axis wind turbine

2016 ◽  
Vol 57 (3) ◽  
Author(s):  
Kevin J. Ryan ◽  
Filippo Coletti ◽  
Christopher J. Elkins ◽  
John O. Dabiri ◽  
John K. Eaton
Keyword(s):  
Flow Field ◽  
Wind Turbine ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Three Dimensional Flow ◽  
Dimensional Flow
Sign in / Sign up

Export Citation Format

Share Document