Characterization of a Ferritic Stainless Sheet Steel in Simple Shear and Uniaxial Tension at Different Strain Rates

2011 ◽  
Author(s):  
Matti Isakov ◽  
Jeremy Seidt ◽  
Kauko O¨stman ◽  
Amos Gilat ◽  
Veli-Tapani Kuokkala
Keyword(s):  
Uniaxial Tension ◽  
Simple Shear ◽  
High Strain ◽  
Image Correlation ◽  
Materials Testing ◽  
Strain Rates ◽  
Test Results ◽  
High Strain Rates ◽  
Stress Strain

In this study the mechanical properties of ferritic stainless steel EN 1.4521 (AISI 444) were characterized in uniaxial tension and simple shear. The specimen geometries were designed so that tests could be carried out both with a conventional uniaxial materials testing machine and at high strain rates with the Tensile Hopkinson Split Bar method. During the tests, specimen surface deformation was measured using a three dimensional digital image correlation technique based on a two-camera stereovision setup. This technique allowed direct measurement of the specimen gauge section deformation during the test. Test results indicate that the selected approach is suitable for large strain plastic deformation characterization of ductile metals. The stress-strain data obtained from the simple shear tests shows a correlation with the tensile test results according to the von Mises effective stress-strain criterion. Since necking is absent in shear, test data can be obtained at considerably higher plastic strains than in tension. However, the final fracture occurs under a complex loading mode due to the distortion of the specimen geometry and multiaxial loading introduced by the simple shear arrangement. Test results also show that reliable material data can be obtained at high strain rates.

Dynamic Compression Behavior and Numerical Modeling of Ti-6246 Alloy at Different Temperatures

2012 ◽  
Vol 527 ◽  
pp. 159-164 ◽  
Author(s):  
Dmitri Gomon ◽  
Mikko Hokka ◽  
Veli Tapani Kuokkala
Keyword(s):  
Numerical Modeling ◽  
Strain Rate ◽  
Strain Hardening ◽  
High Strain ◽  
Material Behavior ◽  
Materials Testing ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Strain Hardening Rate

The current research concentrates on the characterization of the mechanical behavior of Ti-6Al-2Sn-4Zr-6Mo alloy. The material was studied in compression using the Split Hopkinson Pressure Bar (SHPB) equipment at high strain rates and conventional servohydraulic materials testing devices at low strain rates. The tests were performed at temperatures ranging from room temperature up to 600 °C. According to the results of the compression tests, the strain hardening rate of the studied material decreases strongly with increasing strain rate. The observed strong decrease in the strain hardening rate with increasing strain rate is a consequence of the extremely strong adiabatic heating of the material due to its high strength and low thermal conductivity. In this study, the Johnson-Cook material model parameters were obtained from isothermal stress-strain curves that were calculated from the experimental (adiabatic) stress-strain data. In this paper, the results of the mechanical testing at high strain rates and the numerical modeling of the material behavior are presented and discussed in details.

INVESTIGATING THE INFLUENCE OF ENVIRONMENTAL CONDITIONING ON EPOXY RESINS AT QUASISTATIC AND HIGH STRAIN RATES FOR MATERIAL OPERATING LIMIT

2021 ◽  
Author(s):  
SAGAR M. DOSHI, SAGAR M. DOSHI, ◽  
NITHINKUMAR MANOHARAN ◽  
BAZLE Z. (GAMA) HAQUE, ◽  
JOSEPH DEITZEL ◽  
JOHN W. GILLESPIE, JR.
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Yield Stress ◽  
High Strain ◽  
Operating Conditions ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Wide Range ◽  
Environmental Aging

Epoxy resin-based composite panels used for armors may be subjected to a wide range of operating temperatures (-55°C to 76°C) and high strain rates on the order of 103-104 s-1. Over the life cycle, various environmental factors also affect the resin properties and hence influence the performance of the composites. Therefore, it is critical to determine the stress-strain behavior of the epoxy resin over a wide range of strain rates and temperatures for accurate multi-scale modeling of composites and to investigate the influence of environmental aging on the resin properties. Additionally, the characterization of key mechanical properties such as yield stress, modulus, and energy absorption (i.e. area under the stress-strain curve) at varying temperatures and moisture can provide critical data to calculate the material operating limits. In this study, we characterize mechanical properties of neat epoxy resin, SC-15 (currently used in structural armor) and RDL-RDC using uniaxial compression testing. RDL-RDC, developed by Huntsman Corporation, has a glass transition temperature of ~ 120°C, compared to ~ 85°C of SC-15. A split Hopkinson pressure bar is used for high strain rate testing. Quasistatic testing is conducted using a screw-driven testing machine (Instron 4484) at 10-3 s-1 and 10-1 s-1 strain rates and varying temperatures. The yield stress is fit to a modified Eyring model over the varying strain rates at room temperature. For rapid investigation of resistance to environmental aging, accelerated aging tests are conducted by immersing the specimens in 100°C water for 48 hours. Specimens are conditioned in an environmental chamber at 76 °C and 88% RH until they reach equilibrium. Tests are then conducted at five different temperatures from 0°C to 95°C, and key mechanical properties are then plotted vs. temperature. The results presented are an important step towards developing a methodology to identify environmental operating conditions for composite ground vehicle applications.

Determination of stress-strain characteristics at very high strain rates

1970 ◽  
Vol 10 (9) ◽  
pp. 370-376 ◽  
Author(s):  
C. K. H. Dharan ◽  
F. E. Hauser
Keyword(s):  
High Strain ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Very High

A Dynamic Mechanical Analysis of T2 Copper at High Strain Rates

2019 ◽  
Vol 812 ◽  
pp. 38-44
Author(s):  
Shuai Chen ◽  
Wen Bin Li ◽  
Xiao Ming Wang ◽  
Wen Jin Yao
Keyword(s):  
Yield Strength ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Pure Copper ◽  
Dislocation Slip ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Shpb Test

This work compares the pure copper (T2 copper)’s stress-strain relationship at different strain rates in the uni-axial tension test and Split Hopkinson Pressure Bar (SHPB) test. Small samples were utilized in the high strain rate SHPB test in which the accuracy was modified by numerical simulation. The experimental results showed that the T2 copper’s yield strength at high strain rates largely outweighed the quasi static yield strength. The flow stress in the stress-strain curves at different strain rates appeared to be divergent and increased with the increase in strain rates, showing great strain strengthening and strain rate hardening effects. Metallographic observation showed that the microstructure of T2 copper changed from equiaxed grains to twins and the interaction between the dislocation slip zone grain boundary and twins promoted the super plasticity distortion in T2 copper.

Characterization of the combustion of the mixtures biogas-syngas at high strain rates

Fuel ◽  
2020 ◽  
Vol 271 ◽  
pp. 117580
Author(s):  
Rima Zouagri ◽  
Abdelbaki Mameri ◽  
Fouzi Tabet ◽  
Amar Hadef
Keyword(s):  
High Strain ◽  
Strain Rates ◽  
High Strain Rates

Experimental Studies of the Behaviour at High Strain Rates of Unfilled and Filled Polypropylenes

2006 ◽  
Vol 3-4 ◽  
pp. 363-368 ◽  
Author(s):  
N. Temimi ◽  
Noelle Billon
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
High Strain ◽  
Experimental Studies ◽  
Young Modulus ◽  
Video Camera ◽  
Image Correlation ◽  
Strain Rates ◽  
High Strain Rates ◽  
Low Velocity

Thermo mechanical behaviour of unfilled and filled polypropylenes are studied in tension from 10-4 to 102 s-1. Complementary low velocity compression and shear tests are also performed. A high-speed video camera (up to 2500 frames/s) combined with image analysis, image correlation and an infra red pyrometer allow measuring 3D-strain fields and temperature during tests. Thus, data can be processed without restrictive assumptions. Beside usual (for polymers) temperature and strain rate sensitivities it is found that plastic deformation in these materials does not obey incompressibility assumption. Voiding damage is evidenced in the polymer matrix by SEM observations that result in volume change and significant decrease in Young modulus for both materials. Moreover, an increase in the temperature of more than 10 °C is observed and is likely to modify the behaviour of each material at high strain rates. Shear and compression measurements demonstrate that yield criteria and constitutive equation depend on loading. It is concluded that apparent yield stress in semi-crystalline polypropylene can be a result of a combination of “non strain rate sensitive” “non-cohesive mechanisms” and “strain rate sensitive” “cohesive mechanisms”. Experimental characterisation on polymers should then be revisited as most of the usual assumptions are invalid and non monotonic tests should be generalized.

Sign in / Sign up

Export Citation Format

Share Document