Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Characteristics of Auto-Ignition in Internal Combustion Engines Operated With Gaseous Fuels of Variable Methane Number

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
German Amador ◽  
Jorge Duarte Forero ◽  
Adriana Rincon ◽  
Armando Fontalvo ◽  
Antonio Bula ◽  
...  
Keyword(s):  
Compression Ratio ◽  
Internal Combustion Engines ◽  
Coal Gasification ◽  
Error Function ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Auto Ignition ◽  
Methane Number

This paper explores the feasibility of using Syngas with low methane number as fuel for commercial turbocharged internal combustion engines. The effect of methane number (MN), compression ratio (CR), and intake pressure on auto-ignition tendency in spark ignition internal combustion engines was determined. A nondimensional model of the engine was performed by using kinetics mechanisms of 98 chemical species in order to simulate the combustion of the gaseous fuels produced from different thermochemical processes. An error function, which combines the Livengood–Wu with ignition delay time correlation, to estimate the knock occurrence crank angle (KOCA) was proposed. The results showed that the KOCA decreases significantly as the MN increases. Results also showed that Syngas obtained from coal gasification is not a suitable fuel for engines because auto-ignition takes place near the beginning of the combustion phase, but it could be used in internal combustion engines with reactivity controlled compression ignition (RCCI) technology. For the case of high compression ratio and a high inlet pressure at the engine's manifold, fuels with high MN are suitable for the operating conditions proposed.

scholarly journals MATHEMATICAL MODEL OF AUTOMATION OF THE DIAGNOSIS OF INTERNAL COMBUSTION ENGINES OF THE YAMZ-238 FAMILY

2021 ◽  
pp. 12-23
Author(s):  
Dmytro Borysiuk ◽  
Viacheslav Zelinskyi ◽  
Igor Tverdokhlib ◽  
Yurii Polievoda
Keyword(s):  
Mathematical Model ◽  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Structural Parameters ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Inverse Transformation ◽  
Combustion Engines ◽  
Functional Relationships

Constructive improvement of mobile energy means, in particular their main unit - the internal combustion engine, is directed on: maintenance of differentiation of size of parameters of functioning of mechanisms of systems depending on variability of conditions and modes of operation of cars; increase of technical resource at use of cars on purpose in the set operating conditions. The existing methods and tools for diagnosing vehicle engines do not fully determine their current technical condition, which requires the development of mathematical models to automate the process of diagnosing their components and parts was found іn the analysis of literature sources. The object of diagnosis is a diesel internal combustion engine of the YaMZ-238 family, which is part of the power unit of most vehicles. Mathematical model of automation of the process of diagnosing internal combustion engines of the YaMZ-238 family is presents in the article. Replacing real technical devices with their idealized models allows the widespread use of various mathematical methods. In this case, the internal combustion engine of the YaMZ-238 family, as the object of diagnosis, is presented in the form of a «black box», the input and output parameters of which have a finite set of values. In general, the mathematical model is a system of functional relationships between each diagnostic signal and structural parameters. For internal combustion engines of the YaMZ-238 family, a diagnostic matrix has been compiled, which includes a list of faults and signs of faults. It is determined that the process of diagnosis based on the model of the diagnostic object is possible if the inverse transformation of the number of signs of malfunctions into the number of structural parameters (malfunctions) of the object was unambiguous. The proposed mathematical model of automation of the process of diagnosing internal combustion engines of the family YaMZ-238 will detect faults of components and parts depending on their characteristics.

DEVELOPMENT OF AN ELECTRONIC CONTROL SYSTEM FOR GAS-ENGINES WITH SPARK IGNITION, CONVERTED ON THE BASIS OF DIESEL ENGINES TO WORK FOR ON LIQUEFIED PETROLEUM GAS

2018 ◽  
pp. 12-18 ◽  
Author(s):  
Serhii Kovalov
Keyword(s):  
Control System ◽  
Diesel Engines ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Electronic Control ◽  
Liquefied Petroleum Gas ◽  
Electronic Control System

The expediency and advantages of using gas motor fuels, in particular, liquefied petroleum gas with respect to traditional liquid motor fuels, are shown. Technical solutions for the use of liquefied petroleum gas by diesel engines are presented and analysed. The expediency and advantages of converting diesel engines to gas spark ignition internal combustion engines with respect to conversion to gas diesel engines. Developed by the Ukrainian synthesis technology Avenir Gaz has for converting diesel engines to gas internal combustion engines with spark ignition. According to the synthesis technology of Avenir Gaz, re-equipment of diesel engines of vehicles is carried out on the basis of the universal electronic control system for gas internal combustion engines, which is based on the multifunctional electronic microprocessor control unit Avenir Gaz 37. The developed electronic microprocessor control system for gas internal combustion engines with forced ignition has a modular structure and consists of two main and a number of additional subsystems. A schematic diagram of a universal electronic control system of a gas internal combustion engine with spark ignition for operation on liquefied petroleum gas is presented. The principle of operation of the main subsystems, which include the subsystem of power management and injection of liquefied petroleum gas by gas electromagnetic injectors into the intake manifold of a gas engine, and the principle of operation of the control subsystem of the ignition with two-spark ignition coils are described. A multifunctional electronic control unit Avenir Gaz 37 has been designed and manufactured. Non-motorized tests of the electronic control unit confirmed its performance. Based on the synthesis technology of Avenir Gaz using the universal electronic control system for gas internal combustion engines with the Avenir Gaz 37 ECU, the D-240 diesel engine was converted into a gas spark ignition internal combustion engine of the D-240-LPG model. Keywords: gas internal combustion engine with forced ignition, liquefied petroleum gas (LPG), electronic microprocessor control system for gas internal combustion engines, vehicles operating on LPG.

Exhaust Pressure Estimation and Its Application to Detection and Isolation of Turbocharger System Faults for Internal Combustion Engines

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Yue-Yun Wang ◽  
Ibrahim Haskara
Keyword(s):  
High Speed ◽  
Internal Combustion Engines ◽  
Failure Modes ◽  
Combustion Engine ◽  
Pressure Sensors ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Recirculation Flow ◽  
Model Based

Engine exhaust backpressure is a critical parameter in the calculation of the volumetric efficiency and exhaust gas recirculation flow of an internal combustion engine. The backpressure also needs to be controlled to a presetting limit under high speed and load engine operating conditions to avoid damaging a turbocharger. In this paper, a method is developed to estimate exhaust pressure for internal combustion engines equipped with variable geometry turbochargers. The method uses a model-based approach that applies a coordinate transformation to generate a turbine map for the estimation of exhaust pressure. This estimation can substitute for an expensive pressure sensor, thus saving significant cost for production vehicles. On the other hand, for internal combustion engines that have already installed exhaust pressure sensors, this estimation can be used to generate residual signals for model-based diagnostics. Cumulative sum algorithms are applied to residuals based on multiple sensor fusion, and with the help of signal processing, the algorithms are able to detect and isolate critical failure modes of a turbocharger system.

Application of Mechanisms for the Control of Autoignition in High Power Internal Combustion Engine Fueled With Natural Gas

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Jesus Garcia Garcia ◽  
Marco San Juan Mejia ◽  
Lesme Corredor Martinez
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engine ◽  
Control Strategy ◽  
Internal Combustion Engines ◽  
Feedforward Control ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Control Loop ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a thermodynamic model of a spark ignition internal combustion engine fueled with natural gas is developed in order to estimate the air-fuel-unburned gas temperature at before top dead center (BTDC). This temperature is used as controlled variable in a control loop in order to avoid the autoignition phenomena when the engine operates with a fuel with different methane number from the methane number requirement of the engine. The model formulation is based on a polytropic compression proccess whose coefficient was determined experimentally in a turbocharged internal combustion engine fueled with natural gas. To make feasible the use of differents gaseous fuels from natural gas, it was necessary to design two control strategies to avoid the knocking phenomenon and choose the best one. The ambient temperature is the disturbance considered, whose changes are significant in different places in the world. The first control strategy that was implemented is called “Robust”, which employs a conventional feedback control loop with a robust controller which is designed. The response of this control loop is compared to the response of the second control strategy called “Feedforward control”. The results obtained reveals that Feedforward control strategy has better performance than robust control strategy for this application. The control strategy and the model proposed will allow increase the range of application of gaseous fuels with low methane number (MN) leading to guarantee a safe running in internal combustion engines that currently are fueled with natural gas.

scholarly journals Less wear on the piston skirts of internal combustion engines

2020 ◽  
Vol 21 (3) ◽  
pp. 175-180
Author(s):  
Arthur R. Asoyan ◽  
Alexander S. Gorshkov ◽  
Ani H. Israelyan
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Surface Plastic ◽  
Combustion Engines ◽  
Piston Cylinder ◽  
Operational Life ◽  
Piston Skirts

A significant proportion of mechanical losses in internal combustion engines accounted for mechanical losses in the cylinder-piston group. Depending on the operating modes of the internal combustion engine, contact interaction in the piston-cylinder pair is possible, which leads to wear of the working surfaces of the resource-determining elements and a decrease in the operational life of the power unit as a whole, in connection with which the reduction of friction losses in the internal combustion engine elements and the piston - cylinder liner coupling in particular is relevant. Both domestic and foreign researchers are engaged in the solution of the above described problems, various profiles of pistons, methods of calculating the parameters of the oil layer are proposed, but the practical state of the issue determines the relevance of research in this direction. The paper considers the possibility of reducing the wear of piston skirts by reducing the contact surface in conjugation and providing an oil film in the friction zone, regardless of engine operating conditions. This opportunity is realized by forming a certain macro profile on the working surface of the piston skirt. The formation of the macrorelief was carried out by means of surface plastic deformation, with the reciprocating movement of a spherical tool on the machined surface.

scholarly journals The Importance of Thermal Barrier Coating in Compression and Spark Ignition Engines

2020 ◽  
Vol 9 (4) ◽  
pp. 1738-1742
Keyword(s):  
Thermal Barrier Coating ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Renewable Energy Sources ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Thermal Barrier ◽  
Combustion Engines ◽  
Spark Ignition Engines ◽  
Barrier Coating

This paper explains the importance of applying thermal barrier coating (TBC) technique in internal combustion engines by providing an effective way of reducing gas emission which are carbon monoxide (CO), oxide of nitrogen (NOX), hydrocarbon (HC) including particulate matter (PM) thereby increasing engine performance (brake thermal efficiency) achieved by applying coating layers on some internal combustion engine parts using materials with low thermal conductivities and matched coefficients of thermal expansion (CTE close to the substrate material) which are mainly ceramics. Energy demand for various activities of life is increasing on a daily basis. The world depends majorly on non-renewable energy sources from fossil fuels to meet these energy demands. To be comfortable in life, better means of transportation and provision of power are required. Compression and spark ignition engines which are also called Internal Combustion Engines (ICEs) provide better transport facilities and power. However, combusting these fuels in automobile and stationary engines produces unfriendly atmosphere, contaminates water and air that are consumed by man. Pollution created as a result of combustion of gases in ICE is one of the worst man made contribution to atmospheric pollution.

Sign in / Sign up

Export Citation Format

Share Document