Application of Mechanisms for the Control of Autoignition in High Power Internal Combustion Engine Fueled With Natural Gas

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Jesus Garcia Garcia ◽  
Marco San Juan Mejia ◽  
Lesme Corredor Martinez
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engine ◽  
Control Strategy ◽  
Internal Combustion Engines ◽  
Feedforward Control ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Control Loop ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a thermodynamic model of a spark ignition internal combustion engine fueled with natural gas is developed in order to estimate the air-fuel-unburned gas temperature at before top dead center (BTDC). This temperature is used as controlled variable in a control loop in order to avoid the autoignition phenomena when the engine operates with a fuel with different methane number from the methane number requirement of the engine. The model formulation is based on a polytropic compression proccess whose coefficient was determined experimentally in a turbocharged internal combustion engine fueled with natural gas. To make feasible the use of differents gaseous fuels from natural gas, it was necessary to design two control strategies to avoid the knocking phenomenon and choose the best one. The ambient temperature is the disturbance considered, whose changes are significant in different places in the world. The first control strategy that was implemented is called “Robust”, which employs a conventional feedback control loop with a robust controller which is designed. The response of this control loop is compared to the response of the second control strategy called “Feedforward control”. The results obtained reveals that Feedforward control strategy has better performance than robust control strategy for this application. The control strategy and the model proposed will allow increase the range of application of gaseous fuels with low methane number (MN) leading to guarantee a safe running in internal combustion engines that currently are fueled with natural gas.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Effect of Engine Operating Parameters on Combustion and Emission Characteristics

1992 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Internal Combustion ◽  
Operating Parameters ◽  
Emission Characteristics ◽  
Pollutants Emission

Abstract Numerical simulation of flow, combustion, heat release rate and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data are compared with experimental results and show excellent agreement for peak pressure and the rate of pressure rise as a function of crank angle. The results obtained for NO and CO are also found to be in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multi-component chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

scholarly journals Individual drive of internal combustion engine lubrication system based on switched reluctance motor

2020 ◽  
Vol 6 (2) ◽  
pp. 146-151
Author(s):  
Ihor Holovach ◽  
◽  
Lidiia Kasha ◽  
Ivan Hudzii
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Switched Reluctance Motor ◽  
Internal Combustion ◽  
Hydrodynamic Resistance ◽  
Lubrication System ◽  
Resistance Characteristic ◽  
Switched Reluctance ◽  
Reluctance Motor

The article analyses the modern lubrication systems for internal combustion engines. Systems with mechanical drive components that contain mechanical and electronic components have been found to have a number of disadvantages. In particular, when the internal combustion engine is started cold, when the viscosity of the oil is high, the hydrodynamic resistance characteristic rises sharply, which leads to high pressure at low speeds and the drive requires low pump speeds. Again, the increase in oil temperature causes a decrease in viscosity, the hydrodynamic resistance characteristic becomes flatter. This, in turn, reduces the pressure in the lubrication system and requires an increase in pump speed in order to keep the pressure constant. Based on the analysis, the requirements for lubrication systems are formulated and a separate lubrication system with forced oil supply is proposed in this paper. For the drive of pump lubrication system of the internal combustion engine, a switched reluctance motor is proposed and calculated. Such motor by its qualities is one of the most useful in this type of systems.

scholarly journals Assessment of thermodynamic cycle of internal combustion engine in terms of rightsizing

2019 ◽  
Vol 178 (3) ◽  
pp. 182-186
Author(s):  
Zbigniew SROKA ◽  
Maciej DWORACZYŃSKI
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Internal Combustion ◽  
Research Problem ◽  
Combustion Engines ◽  
Operating Characteristics ◽  
Swept Volume

The modification of the downsizing trend of internal combustion engines towards rightsizing is a new challenge for constructors. The change in the displacement volume of internal combustion engines accompanying the rightsizing idea may in fact mean a reduction or increase of the defining swept volume change factors and thus may affect the change in the operating characteristics as a result of changes in combustion process parameters - a research problem described in this publication. Incidents of changes in the displacement volume were considered along with the change of the compression space and at the change of the geometric degree of compression. The new form of the mathematical dependence describing the efficiency of the thermodynamic cycle makes it possible to evaluate the opera-tion indicators of the internal combustion engine along with the implementation of the rightsizing idea. The work demonstrated the in-variance of cycle efficiency with different forms of rightsizing.

FEATURES OF MEASURING THE CAMSHAFT OF INTERNAL COMBUSTION ENGINES

2021 ◽  
Vol 4 (30) ◽  
pp. 99-105
Author(s):  
A. V. Summanen ◽  
◽  
S. V. Ugolkov ◽  
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Technical Condition ◽  
Combustion Engines

This article discusses the issues of assessing the technical condition of the camshaft, internal combustion engine. The necessary parameters for assessing the technical condition of the engine camshaft have been determined. How and how to measure and calculate this or that parameter is presented in detail. Methods for calculating the parameters are presented. A scheme and method for measuring neck wear, determining the height of the cam, determining the beating of the central journal of the camshaft are proposed. The main defects of the camshafts are presented. The issues of the influence of these parameters on the operability of the camshaft and the internal combustion engine as a whole are considered.

Possibility of using gas lubricant in the cylinders of internal combustion engines of transport vehicles

2021 ◽  
pp. 13-20
Author(s):  
Keyword(s):  
Internal Combustion Engine ◽  
Bearing Capacity ◽  
Power Plants ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Engine Piston ◽  
Suspension Stiffness ◽  
Gas Layer

The prospects of using the gas-static suspension of the internal combustion engine piston in transport vehicles and power plants are considered. The diagram of the piston and the method for calculating the stiffness and bearing capacity of the gas layer surrounding the piston are presented, as well as the results of experiments that showed the relevance of this method. The possibility of gas and static centering of the engine piston is confirmed. Keywords: internal combustion engine, piston, gasstatic suspension, stiffness, bearing capacity, gas medium. [email protected]

Sign in / Sign up

Export Citation Format

Share Document