Effect of Gauge Volume on the Residual Stress Measurement Using Deep Hole Drilling Technique

2010 ◽  
Author(s):  
Amir H. Mahmoudi ◽  
David J. Smith ◽  
Chris E. Truman ◽  
Martyn J. Pavier
Keyword(s):  
Residual Stress ◽  
Material Removal ◽  
Stress Measurement ◽  
Measurement Techniques ◽  
Residual Stress Measurement ◽  
Hole Drilling ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Gauge Volume ◽  
Drilling Technique

Accurate evaluation of residual stress is essential if is to be taken into account in structural integrity assessments. For thick components, many non-destructive residual stress measurement techniques cannot be used since they are unable to measure the stresses deep within the component. Measurement techniques which involve mechanical strain relief through material removal are the only alternative. Recently, it has been found that these techniques may fail to measure the stresses correctly when highly triaxial stresses are present because plastic redistribution can occur when the material removal is carried out. The Deep Hole Drilling technique is a very powerful method to measure the stresses within very thick engineering components. However, it can suffer from high levels of plasticity and lead to inaccurate results. It is shown in the present research that the effect of plasticity on the measured stresses can be eliminated. In the present work, the effect of gauge volume on the plasticity effect is investigated.

Calibration of the Ultrasonic Technique Using the Deep Hole Drilling, Neutron Diffraction and Contour Residual Stress Measurement on a Ring Stiffened Cylindrical Structures

2016 ◽  
Author(s):  
Xavier Ficquet ◽  
Remi Romac ◽  
Douglas Cave ◽  
Ed J. Kingston
Keyword(s):  
Residual Stress ◽  
Neutron Diffraction ◽  
Tensile Test ◽  
Stress Measurement ◽  
Measurement Techniques ◽  
Residual Stress Measurement ◽  
Hole Drilling ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Cylindrical Structures

This paper presents the residual stress measurements carried out on a t-section representative of a ring stiffened cylindrical structures. This paper presents the work carried out to ascertain the residual stresses present within a T-plate section representative of a ring stiffened cylindrical structures. The contour, the deep hole drilling (DHD) and the neutron diffraction (ND) methods were applied to determine the longitudinal component of residual stress in the weld toe of the fillet weld in the as-welded condition. The results of these measurements are presented and compared to highlight agreements and discrepancies in the measured residual stress distributions using these different techniques. Finally, non-destructive residual stress measurement using the ultrasonic (US) technique was carried out on the component. The ultrasonic measurement provides a relative measurement and usually requires a tensile test in order to determine the acoustoelastic constant and the time of flight in a stress-free state. The tensile test requires some material to be extracted from the component. The tensile test can be avoided if other residual stress measurement techniques are used for the calibration. After the calibration the US technique can be deployed on a full-scale ring stiffened cylindrical structures to detect abnormal variation in the residual stress field.

Residual Stress Investigation in a Stainless Steel Ring Welded Circular Disc by Over-Coring Deep Hole Drilling Simulation and Measurement

2014 ◽  
Author(s):  
Gang Zheng ◽  
Sayeed Hossain ◽  
Mike C. Smith ◽  
David J. Smith
Keyword(s):  
Residual Stress ◽  
Neutron Diffraction ◽  
Stress Measurement ◽  
Circular Disc ◽  
Residual Stress Measurement ◽  
Hole Drilling ◽  
Deep Hole ◽  
Deep Hole Drilling ◽  
Welding Simulation ◽  
Drilling Simulation

A circular disc containing a partial ring weld has been devised to permit high levels of residual stress to be created in a relatively small specimen. The purpose of this research is to investigate the residual stress within the weld whilst developing a residual stress measurement method called the over-coring deep hole drilling (oDHD) method. The welding simulation, incremental deep hole drilling (iDHD) simulation and measurement and neutron diffraction were previously studied and reported in [1]. In this paper, the welding simulation results were mapped into a 3D model that included the necessary mesh and boundary conditions to simulate the process of residual measurement using the oDHD method. An experimental programme of residual stress measurement using the oDHD method was then conducted on a welded circular disc. The results from the oDHD simulation and measurement matched well with previous iDHD simulations on the original stress field in the ring weld, which also matched earlier neutron diffraction results.

Uncertainties in Triaxial Residual Stress Measurements

2011 ◽  
Vol 681 ◽  
pp. 498-503 ◽  
Author(s):  
D.M. Goudar ◽  
M.S. Hossain ◽  
Christopher E. Truman ◽  
Ed J. Kingston ◽  
David John Smith
Keyword(s):  
Residual Stress ◽  
Error Analysis ◽  
Cold Water ◽  
Stress Measurement ◽  
Measurement Techniques ◽  
Mechanical Strain ◽  
Hole Drilling ◽  
Stress Distributions ◽  
Deep Hole ◽  
Deep Hole Drilling

Residual stress measurement techniques using mechanical strain relaxation depend on a number of physical quantities and are therefore sensitive to errors associated with the measured data. The resulting stress uncertainties can easily become significant and compromise the usefulness of the results or lead to misinterpretation of the behaviour of the residual stress distributions. It is therefore essential to develop an error analysis procedure for the measurements undertaken. Error analysis procedures for the deep hole drilling (DHD) method are developed to consider triaxial residual stresses. A modified deep hole drilling method, called the incremental deep-hole drilling (iDHD), was applied to measure the near yield residual stress distributions in a cold water quenched aluminium 7010 alloy forged block. The experimental results are used to illustrate the errors.

Finite Element Validation of the over-Coring Deep-Hole Drilling Technique

2011 ◽  
Vol 70 ◽  
pp. 291-296 ◽  
Author(s):  
Sayeed Hossain ◽  
Ed J. Kingston ◽  
Christopher E. Truman ◽  
David John Smith
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Field ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Residual Stress Measurement ◽  
Hole Drilling ◽  
Deep Hole ◽  
Residual Stress Field ◽  
Deep Hole Drilling

The main objective of the present study is to validate a simple over-coring deep-hole drilling (oDHD) residual stress measurement technique by utilising finite element simulations of the technique. A number of three dimensional (3D) finite element analyses (FEA) were carried out to explore the influence of material removal and the cutting sequence during the deep-hole drilling (DHD) residual stress measurement process on the initial residual stress field. Two models were considered in the study. First, the residual stress field predicted in a rapid spray water quenched solid cylinder was used as the initial stress field for the DHD FE model. The DHD reconstructed residual stresses were compared with the initial FE predicted stresses. Different cutting sequences and different dimensions were systematically simulated before arriving at an optimum solution for the oDHD technique. The oDHD technique significantly improved the spatial resolution and was applied in a second model consisting of a 40mm thick butt-welded pipe. The DHD reconstructed residual stresses compared very well with the initial FE predicted weld residual stress thereby validating the oDHD technique.

Residual stress measurement techniques for Ti6Al4V parts fabricated using selective laser melting: state of the art review

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ruben B.O. Acevedo ◽  
Klaudia Kantarowska ◽  
Edson Costa Santos ◽  
Marcio C. Fredel
Keyword(s):  
Residual Stress ◽  
Selective Laser Melting ◽  
Stress Measurement ◽  
State Of The Art ◽  
Measurement Techniques ◽  
Residual Stress Measurement ◽  
Hole Drilling ◽  
X Ray Diffraction ◽  
Laser Melting ◽  
Content Type

Purpose This paper aims to generate a review of available techniques to measure Residual Stress (RS) in Ti6Al4V components made by Ti6Al4V. Design/methodology/approach State of the art; literature review in the field of Residual Stress measurement of Ti6Al4V parts made by selective laser melting (SLM). Findings Different Residual Stress measurement techniques were detailed, regarding its concept, advantages and limitations. Regarding all researched references, hole drilling (semi destructive) and X-ray diffraction (nondestructive) were the most cited techniques for Residual Stress measurement of Ti6Al4V parts made by SLM. Originality/value An extensive analysis of RS measurement techniques for Ti6Al4V parts made by SLM.

Sign in / Sign up

Export Citation Format

Share Document