Properties of (Ti1−xAlx)N coatings for cutting tools prepared by the cathodic arc ion plating method

1992 ◽  
Vol 10 (4) ◽  
pp. 1749-1756 ◽  
Author(s):  
Y. Tanaka ◽  
T. M. Gür ◽  
M. Kelly ◽  
S. B. Hagstrom ◽  
T. Ikeda ◽  
...  
Keyword(s):  
Cutting Tools ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Plating Method ◽  
Cathodic Arc ◽  
Coatings For Cutting Tools

Friction and wear properties of CrAlN and CrVN films deposited by cathodic arc ion plating method

2004 ◽  
Vol 177-178 ◽  
pp. 627-630 ◽  
Author(s):  
M. Uchida ◽  
N. Nihira ◽  
A. Mitsuo ◽  
K. Toyoda ◽  
K. Kubota ◽  
...  
Keyword(s):  
Friction And Wear ◽  
Wear Properties ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Plating Method ◽  
Friction And Wear Properties ◽  
Cathodic Arc

The optimization of molybdenum back contact films for Cu(In,Ga)Se2 solar cells by the cathodic arc ion plating method

2013 ◽  
Vol 548 ◽  
pp. 162-167 ◽  
Author(s):  
Yong Ki Cho ◽  
Gang Sam Kim ◽  
Young Sik Song ◽  
Tae Hong Lim ◽  
Donggeun Jung
Keyword(s):  
Solar Cells ◽  
Back Contact ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Plating Method ◽  
Cathodic Arc

scholarly journals Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

Coatings ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 841
Author(s):  
Yanmei Liu ◽  
Tie-Gang Wang ◽  
Wei Lin ◽  
Qiang Zhu ◽  
Bing Yan ◽  
...  
Keyword(s):  
Cutting Tools ◽  
Medium Carbon Steel ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Mechanical And Tribological Properties ◽  
Hardness Tester ◽  
Coated Tool ◽  
Solid Carbide ◽  
End Mills ◽  
Coating Design

Aluminum rich nitride coatings are often used to protect cutting tools and prolong their service life. In this work, a preoxidation technique and duplex coating design were combined to further improve the bearing capacity and heat resistance of cutting tools. The Al-Cr-Si-N, Al-Cr-Si-O-N, and Al-Cr-Si-N/Al-Cr-Si-O-N duplex coatings were developed by arc ion plating, respectively. The morphology, phase constituents, mechanical and tribological properties of the coatings were characterized and tested by SEM, XRD, a micro-hardness tester, scratch tester, and tribometer. The results showed the coating became more compact and smoother after oxygen doping. However, the Al-Cr-Si-N coating presented the best mechanical properties and tribological behaviors. Its hardness and critical load showed the highest values, which were about 4000 HV and 81 N, respectively. A friction coefficient of 0.67 and wear rate of 1.4 × 10−3 μm3/N·mm were also the lowest values in the study. The three coatings were deposited on the same solid carbide end mills and performed the cutting tests under same conditions. By comparison, the Al-Cr-Si-N coated tool presented the longest tool life and minimum cutting force when cutting C1045 medium-carbon steel. After 90 min of dry milling, the width of the flank wear band (VB) of the AlCrSiN coated tool reached 135 μm, which was much lower than that of the other two coated tools.

Microstructure, mechanical and tribological properties of WC/a-C:H coatings deposited by cathodic arc ion-plating

Vacuum ◽  
2016 ◽  
Vol 132 ◽  
pp. 31-39 ◽  
Author(s):  
Wei Wang ◽  
Vasiliy O. Pelenovich ◽  
M.I. Yousaf ◽  
Shaojian Yan ◽  
Han Bin ◽  
...  
Keyword(s):  
Tribological Properties ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Mechanical And Tribological Properties ◽  
Cathodic Arc
Sign in / Sign up

Export Citation Format

Share Document