scholarly journals Anion ordering enables fast H− conduction at low temperatures

2021 ◽  
Vol 7 (23) ◽  
pp. eabf7883
Author(s):  
Hiroki Ubukata ◽  
Fumitaka Takeiri ◽  
Kazuki Shitara ◽  
Cédric Tassel ◽  
Takashi Saito ◽  
...  
Keyword(s):  
Ionic Conductivity ◽  
Room Temperature ◽  
Structural Transition ◽  
Hexagonal Lattice ◽  
Ionic Conductors ◽  
Activation Barriers ◽  
Energy Devices ◽  
Energy Applications ◽  
Chemical Disorder ◽  
New Energy

The introduction of chemical disorder by substitutional chemistry into ionic conductors is the most commonly used strategy to stabilize high-symmetric phases while maintaining ionic conductivity at lower temperatures. In recent years, hydride materials have received much attention owing to their potential for new energy applications, but there remains room for development in ionic conductivity below 300°C. Here, we show that layered anion-ordered Ba2−δH3−2δX (X = Cl, Br, and I) exhibit a remarkable conductivity, reaching 1 mS cm−1 at 200°C, with low activation barriers allowing H− conduction even at room temperature. In contrast to structurally related BaH2 (i.e., Ba2H4), the layered anion order in Ba2−δH3−2δX, along with Schottky defects, likely suppresses a structural transition, rather than the traditional chemical disorder, while retaining a highly symmetric hexagonal lattice. This discovery could open a new direction in electrochemical use of hydrogen in synthetic processes and energy devices.

The Role of Defects in Li3ClO Solid Electrolyte: Calculations and Experiments

2013 ◽  
Vol 1526 ◽  
Author(s):  
M. Helena Braga ◽  
Verena Stockhausen ◽  
Joana C.E. Oliveira ◽  
Jorge A. Ferreira
Keyword(s):  
Ionic Conductivity ◽  
Solid Electrolyte ◽  
Room Temperature ◽  
Defect Formation ◽  
Ionic Conductors ◽  
Activation Barriers ◽  
Ionic Solid ◽  
Formation Energies ◽  
State Ionic

ABSTRACTWe have analyzed the hopping movement of a new ionic solid electrolyte by calculating defect formation energies and activation barriers. The role of the lattice during diffusion was established. Thermodynamic properties were determined by means of first principles and phonon calculations at working temperatures. The new solid electrolyte, an antiperovskite, Li3-2xMxAO (in which M is a higher valent cation like Ca2+ or Mg2+ and A is a halide like Cl- or Br- or a mixture of halides), was studied either pure or doped. Moreover, we present experimental ionic conductivity data for these novel solid state ionic conductors for the doped and the pure solid electrolyte from room temperature and up to ∼253 °C. In this paper, we compare the ionic conductivity of the latter solid electrolyte with other fast ionic conductors.

How Certain Are the Reported Ionic Conductivities of Thiophosphate-Based Solid Electrolytes? an Interlaboratory Study

2020 ◽  
Author(s):  
Saneyuki Ohno ◽  
Tim Bernges ◽  
Johannes Buchheim ◽  
Marc Duchardt ◽  
Anna-Katharina Hatz ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Ionic Conductivity ◽  
Relative Standard Deviation ◽  
Solid Electrolytes ◽  
Ionic Conductivities ◽  
Ionic Conductors ◽  
Energy Storage Devices ◽  
Activation Barriers ◽  
Storage Devices ◽  
Relative Standard

<p>Owing to highly conductive solid ionic conductors, all-solid-state batteries attract significant attention as promising next-generation energy storage devices. A lot of research is invested in the search and optimization of solid electrolytes with higher ionic conductivity. However, a systematic study of an <i>interlaboratory reproducibility</i> of measured ionic conductivities and activation energies is missing, making the comparison of absolute values in literature challenging. In this study, we perform an uncertainty evaluation via a Round Robin approach using different Li-argyrodites exhibiting orders of magnitude different ionic conductivities as reference materials. Identical samples are distributed to different research laboratories and the conductivities and activation barriers are measured by impedance spectroscopy. The results show large ranges of up to 4.5 mScm<sup>-1</sup> in the measured total ionic conductivity (1.3 – 5.8 mScm<sup>-1</sup> for the highest conducting sample, relative standard deviation 35 – 50% across all samples) and up to 128 meV for the activation barriers (198 – 326 meV, relative standard deviation 5 – 15%, across all samples), presenting the necessity of a more rigorous methodology including further collaborations within the community and multiplicate measurements.</p>

How Certain Are the Reported Ionic Conductivities of Thiophosphate-Based Solid Electrolytes? an Interlaboratory Study

2019 ◽  
Author(s):  
Saneyuki Ohno ◽  
Tim Bernges ◽  
Johannes Buchheim ◽  
Marc Duchardt ◽  
Anna-Katharina Hatz ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Ionic Conductivity ◽  
Relative Standard Deviation ◽  
Solid Electrolytes ◽  
Ionic Conductivities ◽  
Ionic Conductors ◽  
Energy Storage Devices ◽  
Activation Barriers ◽  
Storage Devices ◽  
Relative Standard

<p>Owing to highly conductive solid ionic conductors, all-solid-state batteries attract significant attention as promising next-generation energy storage devices. A lot of research is invested in the search and optimization of solid electrolytes with higher ionic conductivity. However, a systematic study of an <i>interlaboratory reproducibility</i> of measured ionic conductivities and activation energies is missing, making the comparison of absolute values in literature challenging. In this study, we perform an uncertainty evaluation via a Round Robin approach using different Li-argyrodites exhibiting orders of magnitude different ionic conductivities as reference materials. Identical samples are distributed to different research laboratories and the conductivities and activation barriers are measured by impedance spectroscopy. The results show large ranges of up to 4.5 mScm<sup>-1</sup> in the measured total ionic conductivity (1.3 – 5.8 mScm<sup>-1</sup> for the highest conducting sample, relative standard deviation 35 – 50% across all samples) and up to 128 meV for the activation barriers (198 – 326 meV, relative standard deviation 5 – 15%, across all samples), presenting the necessity of a more rigorous methodology including further collaborations within the community and multiplicate measurements.</p>

Cu(OH)2: a New Ferroelectric

1995 ◽  
Vol 28 (5) ◽  
pp. 594-598 ◽  
Author(s):  
S. C. Abrahams ◽  
J. Ravez ◽  
A. Simon ◽  
A. Reller ◽  
H. R. Oswald
Keyword(s):  
Crystal Structure ◽  
Heat Capacity ◽  
Ionic Conductivity ◽  
Curie Temperature ◽  
Room Temperature ◽  
Structural Transition ◽  
Wide Frequency Range ◽  
Dielectric Anomaly ◽  
Frequency Range ◽  
Acta Cryst

The crystal structure of Cu(OH)2, recently redetermined at room temperature by Oswald, Reller, Schmalle & Dubler [Acta Cryst. (1990), C46, 2279–2284], is shown to satisfy the structural criteria for ferroelectricity. The Cu2+ ion at 295 K is displaced 0.131 Å from the most likely paraelectric atomic arrangement, allowing the prediction to be made that the ferroelectric Curie temperature is Tc = 343 K. This prediction is in excellent agreement with an earlier report of a reversible structural transition at 325–335 K in Cu(OH)2. The presence of a λ-shaped anomaly in the heat capacity at about 335 K has been confirmed, and a dielectric anomaly is also observed at similar temperatures over a wide frequency range; the frequency dependence is dispersive, owing at least partly to ionic conductivity. The prediction is hence verified, and Cu(OH)2 is demonstrated experimentally to be a new ferroelectric.

scholarly journals How Certain Are the Reported Ionic Conductivities of Thiophosphate-Based Solid Electrolytes? an Interlaboratory Study

2020 ◽  
Author(s):  
Saneyuki Ohno ◽  
Tim Bernges ◽  
Johannes Buchheim ◽  
Marc Duchardt ◽  
Anna-Katharina Hatz ◽  
...  
Keyword(s):  
Standard Deviation ◽  
Ionic Conductivity ◽  
Relative Standard Deviation ◽  
Solid Electrolytes ◽  
Ionic Conductivities ◽  
Ionic Conductors ◽  
Energy Storage Devices ◽  
Activation Barriers ◽  
Storage Devices ◽  
Relative Standard

<p>Owing to highly conductive solid ionic conductors, all-solid-state batteries attract significant attention as promising next-generation energy storage devices. A lot of research is invested in the search and optimization of solid electrolytes with higher ionic conductivity. However, a systematic study of an <i>interlaboratory reproducibility</i> of measured ionic conductivities and activation energies is missing, making the comparison of absolute values in literature challenging. In this study, we perform an uncertainty evaluation via a Round Robin approach using different Li-argyrodites exhibiting orders of magnitude different ionic conductivities as reference materials. Identical samples are distributed to different research laboratories and the conductivities and activation barriers are measured by impedance spectroscopy. The results show large ranges of up to 4.5 mScm<sup>-1</sup> in the measured total ionic conductivity (1.3 – 5.8 mScm<sup>-1</sup> for the highest conducting sample, relative standard deviation 35 – 50% across all samples) and up to 128 meV for the activation barriers (198 – 326 meV, relative standard deviation 5 – 15%, across all samples), presenting the necessity of a more rigorous methodology including further collaborations within the community and multiplicate measurements.</p>

Electron Microscope study of commensurate-incommensurate phase transition in BaZnGeO4

1990 ◽  
Vol 48 (4) ◽  
pp. 172-173
Author(s):  
Naoki Yamamoto ◽  
Makoto Kikuchi ◽  
Tooru Atake ◽  
Akihiro Hamano ◽  
Yasutoshi Saito
Keyword(s):  
Phase Transition ◽  
Electron Microscope Study ◽  
Room Temperature ◽  
Hexagonal Lattice ◽  
Ferroelectric Materials ◽  
Temperature Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Periodic Arrays ◽  
Modulation Wave Vector

BaZnGeO4 undergoes many phase transitions from I to V phase. The highest temperature phase I has a BaAl2O4 type structure with a hexagonal lattice. Recent X-ray diffraction study showed that the incommensurate (IC) lattice modulation appears along the c axis in the III and IV phases with a period of about 4c, and a commensurate (C) phase with a modulated period of 4c exists between the III and IV phases in the narrow temperature region (—58°C to —47°C on cooling), called the III' phase. The modulations in the IC phases are considered displacive type, but the detailed structures have not been studied. It is also not clear whether the modulation changes into periodic arrays of discommensurations (DC’s) near the III-III' and IV-V phase transition temperature as found in the ferroelectric materials such as Rb2ZnCl4.At room temperature (III phase) satellite reflections were seen around the fundamental reflections in a diffraction pattern (Fig.1) and they aligned along a certain direction deviated from the c* direction, which indicates that the modulation wave vector q tilts from the c* axis. The tilt angle is about 2 degree at room temperature and depends on temperature.

Exploring the Influence of Substitution on the Structure and Transport Properties in the Sodium Superionic Conductor Na11+xSn2+x(Sb1−yPy)1−xS12

2020 ◽  
Author(s):  
Marvin Kraft ◽  
Lara Gronych ◽  
Theodosios Famprikis ◽  
Saneyuki Ohno ◽  
Wolfgang Zeier
Keyword(s):  
Electrochemical Impedance ◽  
Structural Phase ◽  
Ionic Transport ◽  
Sodium Ion ◽  
Ionic Conductors ◽  
Temperature Dependent ◽  
Activation Barriers ◽  
Rietveld Refinements ◽  
High Performing ◽  
The Given

<p>Sulfidic sodium ion conductors are currently investigated for the possible use in all-solid-state sodium ion batteries. The design of high performing electrolytes in terms of temperature-dependent ionic transport is based upon the fundamental understanding of structure – transport relationships within the given structural phase boundaries inherent to the investigated materials class. In this work, the Na<sup>+</sup> superionic structural family of Na<sub>11</sub>Sn<sub>2</sub>PS<sub>12</sub> is explored by using the systematic antimony substitution with phosphorous in Na<sub>11+<i>x</i></sub>Sn<sub>2+<i>x</i></sub>(Sb<sub>1-<i>y</i></sub>P<i><sub>y</sub></i>)<sub>1-<i>x</i></sub>S<sub>12</sub>. A combination of Rietveld refinements against X-ray synchrotron diffraction data with electrochemical impedance spectroscopy is used to monitor the changes in the anionic framework, the Na<sup>+</sup> substructure and the ionic transport. A new simplified descriptor for the average Na<sup>+</sup> diffusion pathways, the average Na<sup>+</sup> polyhedral volume is introduced, which is used to correlate the contraction of the overall lattice and the found activation barriers in the system. This study exemplifies how substitution affects diffusion pathways in ionic conductors and widens the knowledge about the related structural motifs and their influence on the ionic transport in this novel class of ionic conductors.</p>

Defect-Mediated Conductivity Enhancements in Na3-xPn1-xWxS4 (Pn = P, Sb) using Aliovalent Substitutions

2019 ◽  
Author(s):  
Till Fuchs ◽  
Sean Culver ◽  
Paul Till ◽  
Wolfgang Zeier
Keyword(s):  
Ionic Conductivity ◽  
Vacancy Concentration ◽  
Sodium Ion ◽  
High Ionic Conductivity ◽  
Ionic Conductors ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solid State Batteries ◽  
Ion Conducting ◽  
Very High

<p>The sodium-ion conducting family of Na<sub>3</sub><i>Pn</i>S<sub>4</sub>, with <i>Pn</i> = P, Sb, have gained interest for the use in solid-state batteries due to their high ionic conductivity. However, significant improvements to the conductivity have been hampered by the lack of aliovalent dopants that can introduce vacancies into the structure. Inspired by the need for vacancy introduction into Na<sub>3</sub><i>Pn</i>S<sub>4</sub>, the solid solutions with WS<sub>4</sub><sup>2-</sup> introduction are explored. The influence of the substitution with WS<sub>4</sub><sup>2-</sup> for PS<sub>4</sub><sup>3-</sup> and SbS<sub>4</sub><sup>3-</sup>, respectively, is monitored using a combination of X-ray diffraction, Raman and impedance spectroscopy. With increasing vacancy concentration improvements resulting in a very high ionic conductivity of 13 ± 3 mS·cm<sup>-1</sup> for Na<sub>2.9</sub>P<sub>0.9</sub>W<sub>0.1</sub>S<sub>4</sub> and 41 ± 8 mS·cm<sup>-1</sup> for Na<sub>2.9</sub>Sb<sub>0.9</sub>W<sub>0.1</sub>S<sub>4</sub> can be observed. This work acts as a stepping-stone towards further engineering of ionic conductors using vacancy-injection via aliovalent substituents.</p>

Defect-Mediated Conductivity Enhancements in Na3-xPn1-xWxS4 (Pn = P, Sb) using Aliovalent Substitutions

2019 ◽  
Author(s):  
Till Fuchs ◽  
Sean Culver ◽  
Paul Till ◽  
Wolfgang Zeier
Keyword(s):  
Ionic Conductivity ◽  
Vacancy Concentration ◽  
Sodium Ion ◽  
High Ionic Conductivity ◽  
Ionic Conductors ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solid State Batteries ◽  
Ion Conducting ◽  
Very High

<p>The sodium-ion conducting family of Na<sub>3</sub><i>Pn</i>S<sub>4</sub>, with <i>Pn</i> = P, Sb, have gained interest for the use in solid-state batteries due to their high ionic conductivity. However, significant improvements to the conductivity have been hampered by the lack of aliovalent dopants that can introduce vacancies into the structure. Inspired by the need for vacancy introduction into Na<sub>3</sub><i>Pn</i>S<sub>4</sub>, the solid solutions with WS<sub>4</sub><sup>2-</sup> introduction are explored. The influence of the substitution with WS<sub>4</sub><sup>2-</sup> for PS<sub>4</sub><sup>3-</sup> and SbS<sub>4</sub><sup>3-</sup>, respectively, is monitored using a combination of X-ray diffraction, Raman and impedance spectroscopy. With increasing vacancy concentration improvements resulting in a very high ionic conductivity of 13 ± 3 mS·cm<sup>-1</sup> for Na<sub>2.9</sub>P<sub>0.9</sub>W<sub>0.1</sub>S<sub>4</sub> and 41 ± 8 mS·cm<sup>-1</sup> for Na<sub>2.9</sub>Sb<sub>0.9</sub>W<sub>0.1</sub>S<sub>4</sub> can be observed. This work acts as a stepping-stone towards further engineering of ionic conductors using vacancy-injection via aliovalent substituents.</p>

Electrochemical Deposition of Polypyrrole Nanostructures for Energy Applications: A Review

2020 ◽  
Vol 16 (4) ◽  
pp. 462-477 ◽  
Author(s):  
Patrizia Bocchetta ◽  
Domenico Frattini ◽  
Miriana Tagliente ◽  
Filippo Selleri
Keyword(s):  
Lithium Batteries ◽  
High Performance ◽  
Relevant Literature ◽  
Chemical Parameters ◽  
Energy Devices ◽  
Energy Applications ◽  
Physico Chemical ◽  
Potential Applications ◽  
Template Free ◽  
Cathodic Polymerization

By collecting and analyzing relevant literature results, we demonstrate that the nanostructuring of polypyrrole (PPy) electrodes is a crucial strategy to achieve high performance and stability in energy devices such as fuel cells, lithium batteries and supercapacitors. In this critic and comprehensive review, we focus the attention on the electrochemical methods for deposition of PPy, nanostructures and potential applications, by analyzing the effect of different physico-chemical parameters, electro-oxidative conditions including template-based or template-free depositions and cathodic polymerization. Diverse interfaces and morphologies of polymer nanodeposits are also discussed.

Sign in / Sign up

Export Citation Format

Share Document