Pinhole Model Measurement Errors Compensation in 3D Scanners

2019 ◽  
Vol 127 (4) ◽  
pp. 684-690
Author(s):  
A. A. Benuni ◽  
V. Ya. Kolyuchkin
Keyword(s):  
Measurement Errors ◽  
3D Scanners ◽  
Model Measurement ◽  
Pinhole Model

scholarly journals Компенсация погрешностей модели центральной проекции в трехмерных сканерах

2019 ◽  
Vol 127 (10) ◽  
pp. 631
Author(s):  
А.А. Бенуни ◽  
В.Я. Колючкин
Keyword(s):  
Measurement Errors ◽  
3D Scanners ◽  
Model Measurement ◽  
Pinhole Model

AbstractPinhole model measurement errors in 3D triangulation based scanners is studied in the present work. Pupil aberrations of the scanner lenses are shown to cause noticeable errors in determining the coordinates of surface points. The requirements for aberration characteristics are formulated to minimize the error of 3D scanners. A modification of the pinhole model allowing a decrease in the error induced by pupil aberration of lenses of triangulation-based scanners is proposed as well.

Precise on-line Measurement of Lattice Vectors

1990 ◽  
Vol 48 (1) ◽  
pp. 530-531
Author(s):  
W.J. de Ruijter ◽  
Sharma Renu
Keyword(s):  
Electron Microscope ◽  
Measurement Errors ◽  
Dynamic Range ◽  
Structural Information ◽  
Statistical Parameter ◽  
Systematic Errors ◽  
Geometric Distortion ◽  
Crystal Silicon ◽  
Camera System ◽  
On Line

Established methods for measurement of lattice spacings and angles of crystalline materials include x-ray diffraction, microdiffraction and HREM imaging. Structural information from HREM images is normally obtained off-line with the traveling table microscope or by the optical diffractogram technique. We present a new method for precise measurement of lattice vectors from HREM images using an on-line computer connected to the electron microscope. It has already been established that an image of crystalline material can be represented by a finite number of sinusoids. The amplitude and the phase of these sinusoids are affected by the microscope transfer characteristics, which are strongly influenced by the settings of defocus, astigmatism and beam alignment. However, the frequency of each sinusoid is solely a function of overall magnification and periodicities present in the specimen. After proper calibration of the overall magnification, lattice vectors can be measured unambiguously from HREM images.Measurement of lattice vectors is a statistical parameter estimation problem which is similar to amplitude, phase and frequency estimation of sinusoids in 1-dimensional signals as encountered, for example, in radar, sonar and telecommunications. It is important to properly model the observations, the systematic errors and the non-systematic errors. The observations are modelled as a sum of (2-dimensional) sinusoids. In the present study the components of the frequency vector of the sinusoids are the only parameters of interest. Non-systematic errors in recorded electron images are described as white Gaussian noise. The most important systematic error is geometric distortion. Lattice vectors are measured using a two step procedure. First a coarse search is obtained using a Fast Fourier Transform on an image section of interest. Prior to Fourier transformation the image section is multiplied with a window, which gradually falls off to zero at the edges. The user indicates interactively the periodicities of interest by selecting spots in the digital diffractogram. A fine search for each selected frequency is implemented using a bilinear interpolation, which is dependent on the window function. It is possible to refine the estimation even further using a non-linear least squares estimation. The first two steps provide the proper starting values for the numerical minimization (e.g. Gauss-Newton). This third step increases the precision with 30% to the highest theoretically attainable (Cramer and Rao Lower Bound). In the present studies we use a Gatan 622 TV camera attached to the JEM 4000EX electron microscope. Image analysis is implemented on a Micro VAX II computer equipped with a powerful array processor and real time image processing hardware. The typical precision, as defined by the standard deviation of the distribution of measurement errors, is found to be <0.003Å measured on single crystal silicon and <0.02Å measured on small (10-30Å) specimen areas. These values are ×10 times larger than predicted by theory. Furthermore, the measured precision is observed to be independent on signal-to-noise ratio (determined by the number of averaged TV frames). Obviously, the precision is restricted by geometric distortion mainly caused by the TV camera. For this reason, we are replacing the Gatan 622 TV camera with a modern high-grade CCD-based camera system. Such a system not only has negligible geometric distortion, but also high dynamic range (>10,000) and high resolution (1024x1024 pixels). The geometric distortion of the projector lenses can be measured, and corrected through re-sampling of the digitized image.

Development of reference materials with the composition of propyl and isopropyl alcohol solutions

2020 ◽  
pp. 66-72
Author(s):  
Irina A. Piterskikh ◽  
Svetlana V. Vikhrova ◽  
Nina G. Kovaleva ◽  
Tatyana O. Barynskaya
Keyword(s):  
Reference Materials ◽  
Measurement Errors ◽  
Isopropyl Alcohol ◽  
Certified Reference Materials ◽  
Toxic Substances ◽  
Biological Objects ◽  
Margin Of Error ◽  
Measurement Results ◽  
And Control ◽  
Characteristic Mass

Certified reference materials (CRM) composed of propyl (11383-2019) and isopropyl (11384-2019) alcohols solutions were created for validation of measurement procedures and control of measurement errors of measurement results of mass concentrations of toxic substances (alcohol) in biological objects (urine, blood) and water. Two ways of establishing the value of the certified characteristic – mass consentration of propanol-1 or propanol-2 have been studied. The results obtained by the preparation procedure and comparison with the standard are the same within the margin of error.

Sign in / Sign up

Export Citation Format

Share Document