Flow Boiling and Two-Phase Flows in Single Microchannels and Microchannel Heat Sinks: Fundamentals, Differences, and New Areas for Research

2018 ◽  
pp. 185-231
Author(s):  
Cristiano Bigonha Tibiriçá ◽  
Gherhardt Ribatski
Keyword(s):  
Flow Boiling ◽  
Heat Sinks ◽  
Two Phase Flows ◽  
Two Phase ◽  
Microchannel Heat Sinks

Microchannel Size Effects on Two-Phase Local Heat Transfer and Pressure Drop in Silicon Microchannel Heat Sinks With a Dielectric Fluid

2007 ◽  
Author(s):  
Tannaz Harirchian ◽  
Suresh V. Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Heat Sinks ◽  
Dielectric Fluid ◽  
Two Phase ◽  
Microchannel Heat Sinks ◽  
The Heat Transfer Coefficient

Two-phase heat transfer in microchannels can support very high heat fluxes for use in high-performance electronics-cooling applications. However, the effects of microchannel cross-sectional dimensions on the heat transfer coefficient and pressure drop have not been investigated extensively. In the present work, experiments are conducted to investigate the local flow boiling heat transfer in microchannel heat sinks. The effect of channel size on the heat transfer coefficient and pressure drop is studied for mass fluxes ranging from 250 to 1600 kg/m2s. The test sections consist of parallel microchannels with nominal widths of 100, 250, 400, 700, and 1000 μm, all with a depth of 400 μm, cut into 12.7 mm × 12.7 mm silicon substrates. Twenty-five microheaters embedded in the substrate allow local control of the imposed heat flux, while twenty-five temperature microsensors integrated into the back of the substrates enable local measurements of temperature. The dielectric fluid Fluorinert FC-77 is used as the working fluid. The results of this study serve to quantify the effectiveness of microchannel heat transport while simultaneously assessing the pressure drop trade-offs.

Experimental Investigation and Theoretical Model for Subcooled Flow Boiling Pressure Drop in Microchannel Heat Sinks

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Jaeseon Lee ◽  
Issam Mudawar
Keyword(s):  
Pressure Drop ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Heat Sinks ◽  
Bulk Liquid ◽  
Two Phase ◽  
Phase Layer ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Microchannel Heat Sinks

This study examines the pressure drop characteristics of subcooled two-phase microchannel heat sinks. A new model is proposed, which depicts the subcooled flow as consisting of a homogeneous two-phase flow layer near the heated walls of the microchannel and a second subcooled bulk liquid layer. This model is intended for conditions where subcooled flow boiling persists along the entire microchannel and the outlet fluid never reaches bulk saturation temperature. Mass, momentum, and energy control volume conservation equations are combined to predict flow characteristics for thermodynamic equilibrium qualities below zero. By incorporating a relation for apparent quality across the two-phase layer and a new criterion for bubble departure, this model enables the determination of axial variations in two-phase layer thickness and velocity as well as pressure drop. The model predictions are compared with HFE 7100 pressure drop data for four different microchannel sizes with hydraulic diameters of 176–416 μm, mass velocities of 670–5550 kg/m2 s, and inlet temperatures of 0°C and −30°C. The pressure drop database is predicted with a mean absolute error of 14.9%.

Two-Phase Microchannel Heat Sinks: Theory, Applications, and Limitations

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Issam Mudawar
Keyword(s):  
Flow Boiling ◽  
Large Diameter ◽  
Turbine Blades ◽  
Small Diameter ◽  
Jet Impingement ◽  
Heat Sinks ◽  
Geometrical Parameters ◽  
Two Phase ◽  
Microchannel Heat Sinks ◽  
Small Channels

Boiling water in small channels that are formed along turbine blades has been examined since the 1970s as a means to dissipating large amounts of heat. Later, similar geometries could be found in cooling systems for computers, fusion reactors, rocket nozzles, avionics, hybrid vehicle power electronics, and space systems. This paper addresses (a) the implementation of two-phase microchannel heat sinks in these applications, (b) the fluid physics and limitations of boiling in small passages, and effective tools for predicting the thermal performance of heat sinks, and (c) means to enhance this performance. It is shown that despite many hundreds of publications attempting to predict the performance of two-phase microchannel heat sinks, there are only a handful of predictive tools that can tackle broad ranges of geometrical and operating parameters or different fluids. Development of these tools is complicated by a lack of reliable databases and the drastic differences in boiling behavior of different fluids in small passages. For example, flow boiling of certain fluids in very small diameter channels may be no different than in macrochannels. Conversely, other fluids may exhibit considerable “confinement” even in seemingly large diameter channels. It is shown that cutting-edge heat transfer enhancement techniques, such as the use of nanofluids and carbon nanotube coatings, with proven merits to single-phase macrosystems, may not offer similar advantages to microchannel heat sinks. Better performance may be achieved by careful optimization of the heat sink’s geometrical parameters and by adapting a new class of hybrid cooling schemes that combine the benefits of microchannel flow with those of jet impingement.

Comparison of 30 Boiling and Condensation Correlations for Two-Phase Flows in Compact Plate-Fin Heat Exchangers

2017 ◽  
Author(s):  
Wenhai Li ◽  
Ken Alabi ◽  
Foluso Ladeinde
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase Flows ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Heat Exchanger Design ◽  
Micro Channels ◽  
Vertical Tubes

Over the years, empirical correlations have been developed for predicting saturated flow boiling [1–15] and condensation [16–30] heat transfer coefficients inside horizontal/vertical tubes or micro-channels. In the present work, we have examined 30 of these models, and modified many of them for use in compact plate-fin heat exchangers. However, the various correlations, which have been developed for pipes and ducts, have been modified in our work to make them applicable to extended fin surfaces. The various correlations have been used in a low-order, one-dimensional, finite-volume type numerical integration of the flow and heat transfer equations in heat exchangers. The NIST’s REFPROP database [31] is used to account for the large variations in the fluid thermo-physical properties during phase change. The numerical results are compared with Yara’s experimental data [32]. The validity of the various boiling and condensation models for a real plate-fin heat exchanger design is discussed. The results show that some of the modified boiling and condensation correlations can provide acceptable prediction of heat transfer coefficient for two-phase flows in compact plate-fin heat exchangers.

Design of a Microscale Breather for Two-Phase Thermal Management Devices

2008 ◽  
Author(s):  
B. R. Alexander ◽  
E. N. Wang
Keyword(s):  
Phase Change ◽  
Removal Rate ◽  
Heat Removal ◽  
Design Guidelines ◽  
Heat Sinks ◽  
Two Phase ◽  
Cross Sectional ◽  
Optical Visualization ◽  
Gas Removal ◽  
Microchannel Heat Sinks

Two-phase microchannels promise an efficient method to dissipate heat from high performance electronic systems by utilizing the latent heat of vaporization during the phase-change process. However, phase-change in microchannel heat sinks leads to challenges that are not present in macroscale systems due to the increasing importance of surface tension and viscous forces. In particular, flow instabilities often occur during the boiling process, which lead to liquid dry-out in the microchannels and severely limits the heat removal capabilities of the system. We propose a microscale breather device consisting of an array of hydrophobic breather ports which allow vapor bubbles to escape from the microchannels to improve flow stability. In this study, we use the combination of microfabricated structures and surface chemistry to separate vapor from the liquid flow. We designed test devices that allow for cross-sectional optical visualization to better understand the governing parameters of a breather design with high vapor removal efficiencies and minimal liquid leakage. We examined breather devices with average liquid velocities ranging from 0.5 cm/s to 4 cm/s and breather vacuum levels between 1 kPa and 9 kPa on the maximum gas removal rate through the breather. We demonstrated successful breather performance. In addition, a model was developed that offers design guidelines for future integrated breathers in microchannel heat sinks. The breathers also have significant promise for other microscale systems, such as micro-fuel cells, where liquid-vapor separation can significantly enhance system performance.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2004 ◽  
Vol 126 (3) ◽  
pp. 288-300 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406×2.032mm2 cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Features unique to two-phase micro-channel flow were identified and employed to validate key assumptions of an annular flow boiling model that was previously developed to predict pressure drop and heat transfer in two-phase micro-channel heat sinks. This earlier model was modified based on new findings from the adiabatic two-phase flow study. The modified model shows good agreement with experimental data for water-cooled heat sinks.

Sign in / Sign up

Export Citation Format

Share Document