FATIGUE STRENGTH ASSESSMENT OF THE FILLET WELDED CRUCIFORM JOINTS

2006 ◽  
Vol 20 (25n27) ◽  
pp. 4225-4230
Author(s):  
DAE-JIN KIM ◽  
CHANG-SUNG SEOK ◽  
JAE-MEAN KOO
Keyword(s):  
Fatigue Strength ◽  
Stress Concentration ◽  
Hot Spot ◽  
Fatigue Tests ◽  
Structural Stress ◽  
Hot Spot Stress ◽  
Cruciform Joints ◽  
Strength Assessment ◽  
Load Carrying ◽  
Cruciform Joint

In this study, fatigue tests to obtain S - N curves and FE analyses to obtain structural stress concentration factors were conducted for two types of fillet welded cruciform joints, that is, load-carrying and non load-carrying types. The obtained S - N curve of the load-carrying joint was changed to that based on hot-spot stress. As a result, the S - N curve of the load-carrying joint based on hot-spot stress almost coincided with that of the non load-carrying joint based on nominal stress. The fatigue strength of a welded joint which has a different geometry from that of the non load-carrying cruciform joint but the same bead profile as that of the non load-carrying cruciform joint could be estimated by using both the structural stress concentration factor at the weld toe position obtained from FEM and the nominal S - N curve of the non load-carrying cruciform joint from experiment.

A Comparative Study on the Fatigue Evaluation for Weldments under Out-of Plane Bending Load Using Structural Stress and Hot Spot Stress

2006 ◽  
Vol 326-328 ◽  
pp. 995-998
Author(s):  
Myung Hyun Kim ◽  
Chung In Ha ◽  
Sung Won Kang ◽  
Jeong Hwan Kim ◽  
Jae Myung Lee
Keyword(s):  
Fatigue Strength ◽  
Hot Spot ◽  
Mesh Size ◽  
Structural Stress ◽  
Hot Spot Stress ◽  
Strength Assessment ◽  
Bending Load ◽  
Load Carrying ◽  
Out Of Plane ◽  
Plane Bending

Fatigue strength assessments with two types of load carrying fillet weldment under out-of-plane bending load have been carried out by using both hot spot stress and structural stress methods. Basis for the derivation of structural stress method is discussed in detail. Finite element analyses using shell elements models have been performed for the fatigue strength assessment of weldments. As a result of the fatigue strength evaluation for load carrying transverse fillet weldment, hot spot stress method is found to be consistent with structural stress method as well as measurement. Hot spot stress, however, estimated for the load carrying longitudinal fillet weldment exhibit large variation with respect to mesh size and element type while the calculated structural stress for the longitudinal fillet weldment is relatively independent of mesh size. The fatigue life estimation according to structural stress has been introduced with the master S-N curve.

Design Analysis and Fatigue Testing of the Typical Structural Details of Aluminium Ships

2018 ◽  
Author(s):  
Huilong Ren ◽  
Kaikai Ma ◽  
Chenfeng Li ◽  
Zhichao Zhang ◽  
Weijun Xu ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Aluminium Alloy ◽  
Fatigue Testing ◽  
Hot Spot ◽  
Fatigue Tests ◽  
Material Strength ◽  
Original Design ◽  
Hot Spot Stress ◽  
Strength Assessment ◽  
Structural Details

Aluminium alloy is widely used structural design in light-weighting design. Due to the material strength loss in welding, fatigue strength of typical joints fabricated by aluminium alloy is more sensitive than steel joints. The aim of this study is to investigate one aluminium detail of the longitudinal through the transverse, with high-performance of fatigue strength compared to the original design. The alloy of longitudinal is AA6082-T6 and the other components (including plate and transverse) is AA5083-H2. Firstly, eight schemes of structural details with various configurations of bracket and / or stiffener are designed. Based on the finite element analyses, the stress distribution of panels with eight designed details is obtained under typical loading condition respectively. According to the principle of hot spot stress being minimum, the optimal detail is determined, which using stiffener reinforced on both sides of transverse. Secondly, the fatigue tests of the optimal detail were designed and carried out. The testing panels consist of 2-span and 3 longitudinal stiffeners, and the frame with optimal joints is located in the middle of the panels. The test panels were simply supported at two ends with applied cyclic loading in the middle panel. According to the designed loading scheme (loading level, frequency, etc.), the fatigue tests of the panels with typical detail were carried out. The hot stress and the cycle times of the typical detail under different load levels were obtained. Based on the test data, the S-N curve of the typical detail in aluminium alloy is established. Finally, the fatigue strength assessment of the typical detail in target ship is performed based on the Miner’s linear cumulative damage theory and established S-N curve. The results show that the fatigue life of proposed optimal detail meets the design requirements of the target ship. The S-N curve of the typical detail made of AA6082-T6 obtained in this study can be also used for other aluminium ships with similar structural details.

Uncertainty Modeling for Fatigue Strength Assessment of Welded Structures

1998 ◽  
Vol 120 (2) ◽  
pp. 97-102 ◽  
Author(s):  
W. Fricke ◽  
A. Mu¨ller-Schmerl
Keyword(s):  
Fatigue Strength ◽  
Hot Spot ◽  
Offshore Structures ◽  
Fatigue Tests ◽  
Published Data ◽  
Hot Spot Stress ◽  
Total Uncertainty ◽  
Strength Assessment ◽  
Characteristic Values ◽  
Fatigue Strength Assessment

The results of fatigue tests are characterized by much scatter. Such scatter is further increased if data from different test series are combined to derive, for instance, characteristic values for individual types of welded joints used in codes. Characteristic values are normally applied to the design of fatigue-resistant ship and offshore structures in connection with the nominal stress approach using S-N curves. More advanced approaches such as the hot-spot stress approach and the notch stress approach are applied to an increasing extent. Such approaches explicitly consider certain influence factors and allow the scatter of these factors to be treated individually. This way, probably even the total uncertainty can be reduced. After reviewing the different approaches used for fatigue strength assessment, the sources of scatter are addressed and assigned to factors considered in the different approaches. Based on published data of fatigue tests and imperfections observed in real structures, an attempt is made to quantify the uncertainties of the different factors and to draw conclusions for their individual consideration in the approaches mentioned.

Fatigue Strength Evaluation of the Load-Carrying Cruciform Fillet Welded Joints Using Hot-Spot Stress

2006 ◽  
Vol 324-325 ◽  
pp. 1281-1284 ◽  
Author(s):  
Byeong Wook Noh ◽  
Jung I. Song ◽  
Sung In Bae
Keyword(s):  
Fatigue Strength ◽  
Welded Joints ◽  
Hot Spot ◽  
Plate Thickness ◽  
Structural Stress ◽  
Leg Length ◽  
Element Analysis ◽  
Hot Spot Stress ◽  
Load Carrying ◽  
Weld Toe

In this study, fatigue strength of load-carrying cruciform fillet welded joints were evaluated using a new method proposed by Yamada, for geometric or structural stress in welded joint, that is, one-millimeter stress below the surface in the direction corresponding to the expected crack path. Validity of the method is verified by analyzing fatigue test results for load-carrying cruciform welded specimens has different size of weld toe radius, leg length and plate thickness reported in literature. Structural stress concentration factor for 1mm below the surface was calculated by finite element analysis for each specimen respectively. When compared to the basic fatigue resistance curve offered by BS7608, the one-millimeter stress method shows conservative evaluation for load-carrying cruciform fillet welded joints.

Fatigue Strength Assessment of the Cruciform Fillet Welded Joint Using Hot-spot Stress Approach

2005 ◽  
Vol 29 (11) ◽  
pp. 1488-1493 ◽  
Author(s):  
Chang-Sung Seok ◽  
Dae-Jin Kim ◽  
Jae-Mean Koo ◽  
Jung-Won Seo ◽  
Byeong-Choon Goo
Keyword(s):  
Fatigue Strength ◽  
Welded Joint ◽  
Hot Spot ◽  
Hot Spot Stress ◽  
Strength Assessment ◽  
Fatigue Strength Assessment

scholarly journals Analysis of fatigue behavior of welded joints in orthotropic bridge deck using traction structural stress

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401989021 ◽  
Author(s):  
Haibo Yang ◽  
Hongliang Qian ◽  
Ping Wang ◽  
Pingsha Dong
Keyword(s):  
Stress Concentration ◽  
Stress Concentration Factor ◽  
Welded Joints ◽  
Concentration Factor ◽  
Hot Spot ◽  
Fatigue Behavior ◽  
Steel Bridge ◽  
Structural Stress ◽  
Test Results ◽  
Hot Spot Stress

In this study, the fatigue behavior of welded joints in an orthotropic steel bridge is simulated and analyzed. The traction structural stress method is proven to be more accurate and effective, and the predicted results agree well with the test results compared to traditional assessment methods, including the nominal stress, hot-spot stress, and effective notch stress methods. The traction structural stress concentration factor curves of welded joints under cyclic tensile and bending moment loading are obtained. The accuracy and validity of finite-element simulation methods for welded joints in orthotropic steel bridge are verified by comparing simulation results with full-scale tests results. Equivalent nominal stresses predicted by the master S–N curve method based on traction structural stress results agree well with the fatigue test results with small standard deviation. The fatigue behavior of orthotropic steel bridge analysis specifications Eurocode3 and GB50017 is combined with the traction structural stress method using unified traction structural stress concentration factor curves. This approach provides practical guidance for the fatigue behavior design of orthotropic steel bridges.

Sign in / Sign up

Export Citation Format

Share Document