A FINITE ELEMENT ANALYSIS OF EFFECTIVE THERMOELECTROELASTIC PROPERTIES OF COMPOSITES WITH A DOUBLY PERIODIC ARRAY OF PIEZOELECTRIC FIBERS

2009 ◽  
Vol 23 (06n07) ◽  
pp. 1689-1694 ◽  
Author(s):  
PENG YAN ◽  
CHIPING JIANG
Keyword(s):  
Finite Element ◽  
Effective Properties ◽  
Cell Model ◽  
Periodic Array ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Uniform Temperature Field ◽  
Periodic Microstructures ◽  
Doubly Periodic Array ◽  
Electrical Loads

This work deals with modeling of 1-3 thermoelectroelastic composites with a doubly periodic array of piezoelectric fibers under arbitrary combination of mechanical, electrical loads and a uniform temperature field. The finite element method (FEM) based on a unit cell model is extended to take into account the thermoelectroelastic effect. The FE predictions of effective properties for several typical periodic microstructures are presented, and their influences on effective properties are discussed. A comparison with the Mori-Tanaka method is made to estimate the application scope of micromechanics. The study is useful for the design and assessment of composites.

Uniaxial Loading in an Elastic Continuum With a Doubly Periodic Array of Material Discontinuities

1969 ◽  
Vol 36 (1) ◽  
pp. 134-139 ◽  
Author(s):  
G. H. Gaonkar
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Periodic Array ◽  
Numerical Comparison ◽  
The Finite Element Method ◽  
Displacement Fields ◽  
Elastic Continuum ◽  
Stress And Displacement Fields ◽  
Material Discontinuities ◽  
Doubly Periodic Array

Stress and displacement fields are presented for uniaxially loaded infinite elastic continua with a doubly periodic array of holes, elastic or rigid inclusions with or without overlapping. The results are obtained by using an appropriate form of the finite-element method. When possible, a numerical comparison has been made with known solutions. In the treatment of not previously studied configurations, the convergence is ascertained by observing the trend with finer discretizations.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Tire Cornering Simulation Using an Explicit Finite Element Analysis Code

1998 ◽  
Vol 26 (2) ◽  
pp. 109-119 ◽  
Author(s):  
M. Koishi ◽  
K. Kabe ◽  
M. Shiratori
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Test System ◽  
Experimental Results ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Explicit Finite Element ◽  
Explicit Finite Element Analysis ◽  
Element Method

Abstract The finite element method has been used widely in tire engineering. Most tire simulations using the finite element method are static analyses, because tires are very complex nonlinear structures. Recently, transient phenomena have been studied with explicit finite element analysis codes. In this paper, the authors demonstrate the feasibility of tire cornering simulation using an explicit finite element code, PAM-SHOCK. First, we propose the cornering simulation using the explicit finite element analysis code. To demonstrate the efficiency of the proposed simulation, computed cornering forces for a 175SR14 tire are compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering forces agree well with experimental results. After that, parametric studies are conducted by using the proposed simulation.

scholarly journals Image-based semi-multiscale finite element analysis using elastic subdomain homogenization

Meccanica ◽  
2021 ◽  
Author(s):  
J. Jansson ◽  
K. Salomonsson ◽  
J. Olofsson
Keyword(s):  
Finite Element ◽  
Analytical Method ◽  
Effective Properties ◽  
Reference Model ◽  
Computational Time ◽  
Component Level ◽  
Element Analysis ◽  
Model Fidelity ◽  
Multiscale Finite Element ◽  
Anisotropic Elastic

AbstractIn this paper we present a semi-multiscale methodology, where a micrograph is split into multiple independent numerical model subdomains. The purpose of this approach is to enable a controlled reduction in model fidelity at the microscale, while providing more detailed material data for component level- or more advanced finite element models. The effective anisotropic elastic properties of each subdomain are computed using periodic boundary conditions, and are subsequently mapped back to a reduced mesh of the original micrograph. Alternatively, effective isotropic properties are generated using a semi-analytical method, based on averaged Hashin–Shtrikman bounds with fractions determined via pixel summation. The chosen discretization strategy (pixelwise or partially smoothed) is shown to introduce an uncertainty in effective properties lower than 2% for the edge-case of a finite plate containing a circular hole. The methodology is applied to a aluminium alloy micrograph. It is shown that the number of elements in the aluminium model can be reduced by $$99.89\%$$ 99.89 % while not deviating from the reference model effective material properties by more than $$0.65\%$$ 0.65 % , while also retaining some of the characteristics of the stress-field. The computational time of the semi-analytical method is shown to be several orders of magnitude lower than the numerical one.

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

Analytical and Numerical Predictions of Thermoelastic Properties of Carbon Single-Walled Nanotubes

Aerospace ◽  
2005 ◽  
Author(s):  
Vinod P. Veedu ◽  
Davood Askari ◽  
Mehrdad N. Ghasemi-Nejhad
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Graphene Sheet ◽  
Effective Properties ◽  
Constitutive Models ◽  
Thermoelastic Properties ◽  
Asymptotic Homogenization ◽  
Element Analysis ◽  
Single Walled Nanotubes ◽  
Numerical Predictions

The objective of this paper is to develop constitutive models to predict thermoelastic properties of carbon single-walled nanotubes using analytical, asymptotic homogenization, and numerical, finite element analysis, methods. In our approach, the graphene sheet is considered as a non-homogeneous network shell layer which has zero material properties in the regions of perforation and whose effective properties are estimated from the solution of the appropriate local problems set on the unit cell of the layer. Our goal is to derive working formulas for the entire complex of the thermoelastic properties of the periodic network. The effective thermoelastic properties of carbon nanotubes were predicted using asymptotic homogenization method. Moreover, in order to verify the results of analytical predictions, a detailed finite element analysis is followed to investigate the thermoelastic response of the unit cells and the entire graphene sheet network.

Comparison of Buried Pipeline Crossing Assessments Using API RP 1102, Analytical Method and Finite Element Approach

2020 ◽  
Author(s):  
Nikhil Joshi ◽  
Pritha Ghosh ◽  
Jonathan Brewer ◽  
Lawrence Matta
Keyword(s):  
Finite Element ◽  
Analytical Method ◽  
Rapid Assessment ◽  
Buried Pipeline ◽  
The Finite Element Method ◽  
Buried Pipelines ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Element Approach ◽  
Multiple Loading

Abstract API RP 1102 provides a method to calculate stresses in buried pipelines due to surface loads resulting from the encroachment of roads and railroads. The API RP 1102 approach is commonly used in the industry, and widely available software allows for quick and easy implementation. However, the approach has several limitations on when it can be used, one of which is that it is limited to pipelines crossing as near to 90° (perpendicular crossing) as practicable. In no case can the crossing be less than 30° . In this paper, the stresses in the buried pipeline under standard highway vehicular loading calculated using the API RP 1102 method are compared with the results of two other methods; an analytical method that accounts for longitudinal and circumferential through wall bending effects, and the finite element method. The benefit of the alternate analytical method is that it is not subject to the limitations of API RP 1102 on crossing alignment or depth. However, this method is still subject to the limitation that the pipeline is straight and at a uniform depth. The fact that it is analytical in nature allows for rapid assessment of a number of pipes and load configurations. The finite element analysis using a 3D soil box approach offers the greatest flexibility in that pipes with bends or appurtenances can be assessed. However, this approach is time consuming and difficult to apply to multiple loading scenarios. Pipeline crossings between 0° (parallel) and 90° (perpendicular) are evaluated in the assessment reported here, even though these are beyond the scope of API RP 1102. A comparison across the three methods will provide a means to evaluate the level of conservatism, if any, in the API RP 1102 calculation for crossing between 30° and 90° . It also provides a rationale to evaluate whether the API RP 1102 calculation can potentially be extended for 0° (parallel) crossings.

scholarly journals Modeling of Size Effects in Bending of Perforated Cosserat Plates

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Roman Kvasov ◽  
Lev Steinberg
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Numerical Study ◽  
The Finite Element Method ◽  
Classical Elasticity ◽  
Element Analysis ◽  
Plate Deformation ◽  
The Finite Element Analysis ◽  
Circular Holes ◽  
Different Shapes

This paper presents the numerical study of Cosserat elastic plate deformation based on the parametric theory of Cosserat plates, recently developed by the authors. The numerical results are obtained using the Finite Element Method used to solve the parametric system of 9 kinematic equations. We discuss the existence and uniqueness of the weak solution and the convergence of the proposed FEM. The Finite Element analysis of clamped Cosserat plates of different shapes under different loads is provided. We present the numerical validation of the proposed FEM by estimating the order of convergence, when comparing the main kinematic variables with an analytical solution. We also consider the numerical analysis of plates with circular holes. We show that the stress concentration factor around the hole is less than the classical value, and smaller holes exhibit less stress concentration as would be expected on the basis of the classical elasticity.

Sign in / Sign up

Export Citation Format

Share Document