Thermo-viscoelastic fractional model of rotating nanobeams with variable thermal conductivity due to mechanical and thermal loads

2021 ◽  
pp. 2150297
Author(s):  
Ahmed E. Abouelregal ◽  
Hijaz Ahmad ◽  
Taher A. Nofal ◽  
Hanaa Abu-Zinadah

This paper analyzes the thermoelastic dynamic behavior of simply supported viscoelastic nanobeams of fractional derivative type due to a dynamic strength load. The viscoelastic Kelvin–Voigt model with fractional derivative with Bernoulli–Euler beam theory is introduced. The generalized thermoelastic heat conduction model with a two-phase lag is also used. It is assumed that the beam is rotating at a uniform angular velocity and that the thermal conductivity varies linearly depending on the temperature. Due to a variable harmonic heat and retreating time-dependent load, the nanobeam is excited. The Laplace integral transformation technique is used as the solution method. The thermodynamic temperature, deflection function, bending moment, and displacement are numerically calculated. Results of fractional and integer viscoelastic material models are compared. In the studied system, the effect of the nonlocal parameter, viscosity and varying load on the solutions is shown, and the temperature-dependence of the thermal conductivity is analyzed.

2020 ◽  
Vol 59 (1) ◽  
pp. 455-463
Author(s):  
Adnan Jahangir ◽  
Fizza Malik ◽  
Nazir Muhammad ◽  
Rabia Fayyaz ◽  
Javeria Nawaz Abbasi ◽  
...  

AbstractIn this article, we analyzed the effect of variable thermal conductivity on reflected elastic waves. The waves are propagating through a thermoelastic medium rotating with some angular frequency. The concept of micro-temperature is also been considered, in which microelements of the medium contain a high temperature. A heat conduction phenomenon is encountered by dual phase-lag heat conduction model. P (or SV)-type wave is incident on the medium with some specific angle of incidence. After reflection from the surface incident, P-wave is converted into quasi longitudinal and quasi transverse waves and propagates back into the medium. Helmholtz’s potential function along with the harmonic wave solution is used to obtain the solution of the model. Analytically, we calculated the amplitude ratios and attenuation factor for each reflected wave against the angle of incidence. The obtained results are also represented graphically for different values of rotational frequency and variable thermal conductivity for a particular material.


Author(s):  
Ahmed E Aboueregal ◽  
Hamid M Sedighi

The present contribution aims to address a problem of thermoviscoelasticity for the analysis of the transition temperature and thermal stresses in an infinitely circular annular cylinder. The inner surface is traction-free and subjected to thermal shock heating, while the outer surface is thermally insulated and free of traction. In this work, in contrast to the various problems in which the thermal conductivity coefficient is considered to be fixed, this parameter is assumed to be variable depending on the temperature change. The problem is studied by presenting a new generalized thermoelastic model of thermal conductivity described by the Moore–Gibson–Thompson equation. The new model can be constructed by incorporating the relaxation time thermal model with the Green–Naghdi type III model. The Laplace transformation technique is used to obtain the exact expressions for the radial displacement, temperature and the distributions of thermal stresses. The effects of angular velocity, viscous parameter, and variance in thermal properties are also displayed to explain the comparisons of the physical fields.


2014 ◽  
Vol 36 (1) ◽  
pp. 55-62 ◽  
Author(s):  
Dariusz Łydżba ◽  
Adrian Różański ◽  
Magdalena Rajczakowska ◽  
Damian Stefaniuk

Abstract The needle probe test, as a thermal conductivity measurement method, has become very popular in recent years. In the present study, the efficiency of this methodology, for the case of composite materials, is investigated based on the numerical simulations. The material under study is a two-phase composite with periodic microstructure of “matrix-inclusion” type. Two-scale analysis, incorporating micromechanics approach, is performed. First, the effective thermal conductivity of the composite considered is found by the solution of the appropriate boundary value problem stated for the single unit cell. Next, numerical simulations of the needle probe test are carried out. In this case, two different locations of the measuring sensor are considered. It is shown that the “equivalent” conductivity, derived from the probe test, is strongly affected by the location of the sensor. Moreover, comparing the results obtained for different scales, one can notice that the “equivalent” conductivity cannot be interpreted as the effective one for the composites considered. Hence, a crude approximation of the effective property is proposed based on the volume fractions of constituents and the equivalent conductivities derived from different sensor locations.


2016 ◽  
Vol 32 (6) ◽  
pp. 665-671 ◽  
Author(s):  
R. Kumar ◽  
S. Devi

AbstractThe main objective of the present paper is to analyze the effects of phase-lag on thick circular plate with heat sources in modified couple stress thermoelastic medium. The mathematical formulation is prepared for three-phase-lag heat conduction model subjected to prescribed normal heat flux along with stress free boundary. Laplace and Hankel transforms are used to deal the problem. The displacements, stresses and temperature change are obtained in the transformed domain. Numerical inversion technique has been used to obtain the solutions in the physical domain. The results obtained numerically for these quantities are presented graphically. Some particular cases are also discussed in the present problem.


2016 ◽  
Vol 138 (2) ◽  
Author(s):  
Elbara Ziade ◽  
Jia Yang ◽  
Gordie Brummer ◽  
Denis Nothern ◽  
Theodore Moustaks ◽  
...  

Frequency domain thermoreflectance (FDTR) is used to create quantitative maps of thermal conductivity and thickness for a thinning gallium nitride (GaN) film on silicon carbide (SiC). GaN was grown by molecular beam epitaxy on a 4H-SiC substrate with a gradient in the film thickness found near the edge of the chip. The sample was then coated with a 5 nm nickel adhesion layer and a 85 nm gold transducer layer for the FDTR measurement. A piezo stage raster scans the sample to create phase images at different frequencies. For each pixel, a periodically modulated continuous-wave laser (the red pump beam) is focused to a Gaussian spot, less than 2 um in diameter, to locally heat the sample, while a second beam (the green probe beam) monitors the surface temperature through a proportional change in the reflectivity of gold. The pump beam is modulated simultaneously at six frequencies and the thermal conductivity and thickness of the GaN film are extracted by minimizing the error between the measured probe phase lag at each frequency and an analytical solution to the heat diffusion equation in a multilayer stack of materials. A scanning electron microscope image verifies the thinning GaN. We mark the imaged area with a red box. A schematic of the GaN sample in our measurement system is shown in the top right corner, along with the two fitting properties highlighted with a red box. We show the six phase images and the two obtained property maps: thickness and thermal conductivity of the GaN. Our results indicate a thickness dependent thermal conductivity of GaN, which has implications of thermal management in GaN-based high electron mobility transistors.


2006 ◽  
Vol 9 (05) ◽  
pp. 530-542 ◽  
Author(s):  
Hadi Nasrabadi ◽  
Kassem Ghorayeb ◽  
Abbas Firoozabadi

Summary We present formulation and numerical solution of two-phase multicomponent diffusion and natural convection in porous media. Thermal diffusion, pressure diffusion, and molecular diffusion are included in the diffusion expression from thermodynamics of irreversible processes. The formulation and the numerical solution are used to perform initialization in a 2D cross section. We use both homogeneous and layered media without and with anisotropy in our calculations. Numerical examples for a binary mixture of C1/C3 and a multicomponent reservoir fluid are presented. Results show a strong effect of natural convection in species distribution. Results also show that there are at least two main rotating cells at steady state: one in the gas cap, and one in the oil column. Introduction Proper initialization is an important aspect of reliable reservoir simulations. The use of the Gibbs segregation condition generally cannot provide reliable initialization in hydrocarbon reservoirs. This is caused, in part, by the effect of thermal diffusion (caused by the geothermal temperature gradient), which cannot be neglected in some cases; thermal diffusion might be the main phenomenon affecting compositional variation in hydrocarbon reservoirs, especially for near-critical gas/condensate reservoirs (Ghorayeb et al. 2003). Generally, temperature increases with increasing burial depth because heat flows from the Earth's interior toward the surface. The temperature profile, or geothermal gradient, is related to the thermal conductivity of a body of rock and the heat flux. Thermal conductivity is not necessarily uniform because it depends on the mineralogical composition of the rock, the porosity, and the presence of water or gas. Therefore, differences in thermal conductivity between adjacent lithologies can result in a horizontal temperature gradient. Horizontal temperature gradients in some offshore fields can be observed because of a constant water temperature (approximately 4°C) in different depths in the seabed floor. The horizontal temperature gradient causes natural convection that might have a significant effect on species distribution (Firoozabadi 1999). The combined effects of diffusion (pressure, thermal, and molecular) and natural convection on compositional variation in multicomponent mixtures in porous media have been investigated for single-phase systems (Riley and Firoozabadi 1998; Ghorayeb and Firoozabadi 2000a).The results from these references show the importance of natural convection, which, in some cases, overrides diffusion and results in a uniform composition. Natural convection also can result in increased horizontal compositional variation, an effect similar to that in a thermogravitational column (Ghorayeb and Firoozabadi 2001; Nasrabadi et al. 2006). The combined effect of convection and diffusion on species separation has been the subject of many experimental studies. Separation in a thermogravitational column with both effects has been measured widely (Schott 1973; Costeseque 1982; El Mataaoui 1986). The thermogravitational column consists of two isothermal vertical plates with different temperatures separated by a narrow space. The space can be either without a porous medium or filled with a porous medium. The thermal diffusion, in a binary mixture, causes one component to segregate to the hot plate and the other to the cold plate. Because of the density gradient caused by temperature and concentration gradients, convection flow occurs and creates a concentration difference between the top and bottom of the column. Analytical and numerical models have been presented to analyze the experimental results (Lorenz and Emery 1959; Jamet et al. 1992; Nasrabadi et al. 2006). The experimental and theoretical studies show that the composition difference between the top and bottom of the column increases with permeability until an optimum permeability is reached. Then, the composition difference declines as permeability increases. The process in a thermogravitational column shows the significance of the convection from a horizontal temperature gradient.


Sign in / Sign up

Export Citation Format

Share Document